Deutsch
EnglishMobility for your BMW 7 Series 2008-2014
Mobility
To ensure that you remain mobile at all times, this
chapter supplies you with important information
on the topics of fuels and lubricants, wheels and
tires, service, maintenance, and Roadside
Assistance.
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Refueling
Do not pinch the retaining strap
Fuel cap
Do not pinch the retaining strap attached
to the cap; otherwise, the cap cannot be closed
properly and fuel vapors can escape.
Opening
1. Briefly press the rear edge of the fuel filler
flap.
A message is displayed if the cap is loose or
missing.◀
Manually unlocking fuel filler flap
In the event of an electrical malfunction, for ex‐
ample.
2. Turn the fuel cap counterclockwise.
Pull the green knob with the fuel pump symbol.
This releases the fuel filler flap.
Observe the following when
refueling
The fuel tank is full when the filler nozzle clicks
off the first time.
3. Place the fuel cap in the bracket attached to
the fuel filler flap.
Handling fuels
Obey safety regulations posted at the gas
station.◀
Fuel tank capacity
Gasoline engine Fuel tank capacity: approx.
21.6 US gal/82 liters.
Closing
Refuel promptly
1. Fit the cap and turn it clockwise until you
clearly hear a click.
Refuel below a range of 30 miles/50 km;
otherwise, engine functions are not ensured and
damage may occur.◀
2. Close the fuel filler flap.
242
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Fuel
Minimum fuel grade
Fuel quality
The use of poor-quality fuels may result in
driveability, starting and stalling problems es‐
pecially under certain environmental conditions
such as high ambient temperature and high al‐
titude.
Refuel with unleaded fuel only
Do not use leaded fuel as this would per‐
manently damage the catalytic converter.◀
Do not refuel with ethanol
Should you encounter driveability problems
which you suspect could be related to the fuel
you are using, we recommend that you respond
by switching to a recognized high-quality brand
such as gasoline that is advertised as Top Tier
Detergent Gasoline.
Do not refuel with E85, i.e., fuel with an
ethanol content of 85 %, or with Flex Fuel, as this
would damage the engine and fuel supply sys‐
tem.◀
Required fuel
Failure to comply with these recommendations
may result in unscheduled maintenance.◀
Super premium gasoline/AKI 91
This gasoline is highly recommended.
Gasoline with lower AKI
However, you may also use gasoline with less
AKI.
The minimum AKI Rating is 89.
If you use gasoline with this minimum AKI Rat‐
ing, the engine may produce knocking sounds
when starting at high outside temperatures.
This has no effect on the engine life.
Minimum fuel grade
Do not use any gasoline below the mini‐
mum specified fuel grade; otherwise, engine
damage may occur.◀
Use high-quality brands
Field experience has indicated significant differ‐
ences in fuel quality: volatility, composition, ad‐
ditives, etc., among gasolines offered for sale in
the United States and Canada.
Fuels containing up to and including 10 % etha‐
nol or other oxygenates with up to 2.8 % oxygen
by weight, that is, 15 % MTBE or 3 % methanol
plus an equivalent amount of co-solvent, will not
void the applicable warranties with respect to
defects in materials or workmanship.
243
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Wheels and tires
Tire inflation pressures up to 100 mph/
160 km/h
Tire inflation pressure
Safety information
The tire characteristics and tire inflation pres‐
sure influence the following:
For speeds of up to 100 mph/160 km/h and for
optimum driving comfort, note the pressure val‐
ues in the tire inflation pressure table, refer to
page 244, and adjust as necessary.
▷
▷
▷
The service life of the tires.
Road safety.
Driving comfort.
Checking the pressure
Only check the tire inflation pressure when the
tires are cold. This means after driving no more
than 1.25 miles/2 km or when the vehicle has
been parked for at least 2 hours. When the tires
are warm, the tire inflation pressure is higher.
These pressure values can also be found on the
tire inflation pressure label on the driver's door
pillar.
Check the tire inflation pressure regularly
Regularly check the tire inflation pressure
and correct it as needed: at least twice a month
and before a long trip. If you fail to observe this
precaution, you may be driving on tires with in‐
correct tire pressures, a condition that may not
only compromise your vehicle's driving stability,
but also lead to tire damage and the risk of an
accident.◀
Maximum permissible speed
Do not exceed 100 mph/160 km/h; other‐
wise, tire damage and accidents may result.◀
Tire inflation pressure values up to
100 mph/160 km/h
After correcting the tire inflation pressure, rein‐
itialize the Tire Pressure Monitor.
740i, 740Li, 750i, 750Li
Tire size
Pressure specifica‐
tions in bar/PSI
Pressure specifications
The tire inflation pressure table, refer to
page 244, contains all pressure specifications
for the specified tire sizes at the ambient tem‐
perature. Pressure specifications apply to ap‐
proved tire sizes and recommended tire brands.
This information can be obtained from your
service center.
Specifications in bar/
PSI with cold tires
245/50 R 18 100 V M 2.2 / 32
+S A/S
2.4 / 35
To identify the correct tire inflation pressure,
please note the following:
245/50 R 18 100 H M
+S
▷
▷
▷
Tire sizes of your vehicle.
Vehicle load.
Maximum allowable driving speed.
244
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Tire size
Pressure specifica‐
tions in bar/PSI
Tire size
Pressure specifica‐
tions in bar/PSI
245/45 R 19 102 V M 2.4 / 35
+S XL A/S
2.6 / 38
F.: 245/40 R 20 99 Y
XL
2.5 / 36
-
-
2.5 / 36
245/45 R 19 102 V M
+S XL
R.:
275/35 R 20 102 Y XL
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.2 / 32
-
-
F.:
2.8/41
-
-
245/35 R 21 96 Y XL
2.3 / 33
2.9 /42
R.:
F.: 245/40 R 20 99 Y
XL
2.4 / 35
-
-
275/30 R 21 98 Y XL
2.6 / 38
R.:
750i xDrive, 750Li xDrive
275/35 R 20 102 Y XL
F.:
2.6 / 38
-
-
Tire size
Pressure specifica‐
tions in bar/PSI
245/35 R 21 96 Y XL
3.0 / 44
R.:
Specifications in bar/
PSI with cold tires
275/30 R 21 98 Y XL
760Li
245/50 R 18 100 V M 2.2 / 32
+S A/S
2.4 / 35
2.6 / 38
Tire size
Pressure specifica‐
tions in bar/PSI
245/50 R 18 100 H M
+S
Specifications in ar/
PSI with cold tires
245/45 R 19 102 V M 2.4 / 35
+S XL A/S
245/45 R 19 102 V M
+S XL
245/50 R 18 100 V M 2.2 / 32
+S A/S
2.4 / 35
2.6 / 38
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.2 / 32
-
-
245/50 R 18 100 H M
+S
2.3 / 33
245/45 R 19 102 V M 2.4 / 35
+S XL A/S
F.: 245/40 R 20 99 Y
XL
2.5 / 36
-
-
2.6 / 38
245/45 R 19 102 V M
+S XL
R.:
275/35 R 20 102 Y XL
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.3 / 33
-
-
F.:
2.8 / 41
-
-
245/35 R 21 96 Y XL
2.3 / 33
3.0 / 44
R.:
275/30 R 21 98 Y XL
245
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Tire inflation pressures at max. speeds
above 100 mph/160 km/h
Tire size
Pressure specifica‐
tions in bar/PSI
Speeds above 100 mph/160 km/h
Specifications in bar/
PSI with cold tires
In order to drive at maximum speeds in ex‐
cess of 100 mph/160 km/h, please observe, and,
if necessary, adjust tire pressures for speeds
exceeding 100 mph/160 km/h from the relevant
table on the following pages. Otherwise tire
damage and accidents could occur.◀
245/50 R 18 100 H M 2.5 / 36
+S
2.8 / 41
3.2 / 46
245/45 R 19 102 V M 2.7 / 39
+S XL
Tire inflation pressure values over
100 mph/160 km/h
F.: 245/45 R 19 98 Y 2.5 / 36
R.: 275/40 R 19 101 Y -
-
740i, 740Li, 750i, 750Li
2.6 / 38
Without high-speed tuning feature
F.: 245/40 R 20 99 Y 2.7 / 39
-
XL
Tire size
Pressure specifica‐
tions in bar/PSI
-
2.9 /42
R.:
275/35 R 20 102 Y XL
Specifications in bar/
PSI with cold tires
F.:
2.9 /42
-
-
245/35 R 21 96 Y XL
3.3 / 48
R.:
275/30 R 21 98 Y XL
245/50 R 18 100 V M 2.2 / 32
+S A/S
2.6 / 38
2.8 / 41
760i, 760Li
Without high-speed tuning feature
245/50 R 18 100 H M
+S
245/45 R 19 102 V M 2.4 / 35
+S XL A/S
Tire size
Pressure specifica‐
tions in bar/PSI
245/45 R 19 102 V M
+S XL
Specifications in bar/
PSI with cold tires
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.2 / 32
-
-
2.3 / 33
245/50 R 18 100 V M 2.6 / 38
+S A/S
2.8 / 41
3.1 / 45
F.:245/40R2099YXL 2.4 / 35
-
R.:
-
2.6 / 38
245/50 R 18 100 H M
+S
275/35 R 20 102 Y XL
F.:245/35R2196YXL 2.6 / 38
-
245/45 R 19 102 V M 2.8 / 41
+S XL A/S
R.:
-
3.0 / 44
275/30 R 21 98 Y XL
245/45 R 19 102 V M
+S XL
With high-speed tuning feature
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.5 / 36
-
-
2.5 / 36
246
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Tire size
Pressure specifica‐
tions in bar/PSI
Tire size
Pressure specifica‐
tions in bar/PSI
Specifications in psi/
kilopascal with cold
tires
F.:245/40R2099YXL 2.7 / 39
-
R.:
-
2.7 / 39
275/35 R 20 102 Y XL
F.:245/35R2196YXL 3.0 / 44
-
245/50 R 18 100 V M 2.4 / 35
+S A/S
2.6 / 38
2.8 / 41
R.:
-
3.1 / 45
275/30 R 21 98 Y XL
245/50 R 18 100 H M
+S
With high-speed tuning feature
245/45 R 19 102 V M 2.6 / 38
+S XL A/S
Tire size
Pressure specifica‐
tions in bar/PSI
245/45 R 19 102 V M
+S XL
Specifications in psi/
kilopascal with cold
tires
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.2 / 32
-
-
2.3 / 33
F.: 245/40 R 20 99 Y
XL
2.5 / 36
-
-
245/50 R 18 100 V M 2.6 / 38
+S A/S
2.8 / 41
3.1 / 45
2.6 / 38
R.:
245/50 R 18 100 H M
+S
275/35 R 20 102 Y XL
F.:
2.8 / 41
-
-
245/45 R 19 102 V M 2.8 / 41
+S XL A/S
245/35 R 21 96 Y XL
3.0 / 44
R.:
245/45 R 19 102 V M
+S XL
275/30 R 21 98 Y XL
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.6 / 38
-
-
With high-speed tuning feature
2.6 / 38
Tire size
Pressure specifica‐
tions in bar/PSI
F.: 245/40 R 20 99 Y
XL
2.8 / 41
-
-
2.8 / 41
Specifications in psi/
kilopascal with cold
tires
R.:
275/35 R 20 102 Y XL
F.:
3.2 / 46
-
-
245/35 R 21 96 Y XL
3.2 / 46
245/50 R 18 100 V M 2.6 / 38
+S A/S
2.9 /42
R.:
275/30 R 21 98 Y XL
245/50 R 18 100 H M
+S
750i xDrive, 750Li xDrive
Without high-speed tuning feature
247
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
3510: tire age
Tire size
Pressure specifica‐
tions in bar/PSI
Tires with DOT codes meet the guidelines of the
U.S. Department of Transportation.
245/45 R 19 102 V M 2.8 / 41
+S XL A/S
3.2 / 46
Tire age
245/45 R 19 102 V M
+S XL
DOT … 3510: the tire was manufactured in the
35th week in 2010.
F.: 245/45 R 19 98 Y
R.: 275/40 R 19 101 Y
2.4 / 35
-
-
Recommendation
Regardless of wear, replace tires at least every
6 years.
2.5 / 36
F.: 245/40 R 20 99 Y
XL
2.7 / 39
-
-
2.7 / 39
R.:
Uniform Tire Quality Grading
275/35 R 20 102 Y XL
Quality grades can be found where applicable
on the tire sidewall between tread shoulder and
maximum section width.
F.:
3.0 / 44
-
-
245/35 R 21 96 Y XL
3.2 / 46
For example: Treadwear 200; Traction AA;
Temperature A
R.:
275/30 R 21 98 Y XL
DOT Quality Grades
Treadwear
Tire identification marks
Traction AA A B C
Temperature A B C
Tire size
All passenger car tires must conform to Federal
Safety Requirements in addition to these
grades.
255/50 R 19 103 Y
255: nominal width in mm
50: aspect ratio in %
R: radial tire code
Treadwear
19: rim diameter in inches
103: load rating, not for ZR tires
Y: speed rating, before the R on ZR tires
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov‐
ernment test course. For example, a tire graded
150 would wear one and one-half, 1 g, times as
well on the government course as a tire graded
100. The relative performance of tires depends
upon the actual conditions of their use, however,
and may depart significantly from the norm due
to variations in driving habits, service practices
and differences in road characteristics and cli‐
mate.
Speed letter
T = up to 118 mph, 190 km/h
H = up to 131 mph, 210 km/h
V = up to 150 mph, 240 km/h
W = up to 167 mph, 270 km/h
Y = up to 186 mph, 300 km/h
Tire Identification Number
DOT code: DOT xxxx xxx 3510
xxxx: manufacturer code for the tire brand
xxx: tire size and tire design
Traction
The traction grades, from highest to lowest, are
AA, A, B, and C.
248
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Those grades represent the tire's ability to stop
on wet pavement as measured under controlled
conditions on specified government test surfa‐
ces of asphalt and concrete. A tire marked C may
have poor traction performance.
Tire tread
Summer tires
Do not drive with a tire tread depth of less than
0.12 in/3 mm.
The traction grade assigned to this tire is based
on straight-ahead braking traction tests, and
does not include acceleration, cornering, hydro‐
planing, or peak traction characteristics.
There is an increased danger of hydroplaning if
the tread depth is less than 0.12 in/3 mm.
Winter tires
Do not drive with a tire tread depth of less than
0.16 in/4 mm.
Temperature
The temperature grades are A, the highest, B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions
on a specified indoor laboratory test wheel. Sus‐
tained high temperature can cause the material
of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire
failure. The grade C corresponds to a level of
performance which all passenger car tires must
meet under the Federal Motor Vehicle Safety
Standard No. 109. Grades Band A represent
higher levels of performance on the laboratory
test wheel than the minimum required by law.
Below a tread depth of 0.16 in/4 mm, tires are
less suitable for winter operation.
Minimum tread depth
Temperature grade for this tire
Wear indicators are distributed around the tire's
circumference and have the legally required
minimum height of 0.063 in/1.6 mm.
The temperature grade for this tire is es‐
tablished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla‐
tion, or excessive loading, either separately or in
combination, can cause heat buildup and pos‐
sible tire failure.
They are marked on the side of the tire with TWI,
Tread Wear Indicator.
If necessary, have the vehicle towed.◀
Tire damage
RSC – Run-flat tires
General information
Run-flat tires, refer to page 251, are labeled with
a circular symbol containing the letters RSC
marked on the sidewall.
Inspect your tires often for damage, foreign ob‐
jects lodged in the tread, and tread wear.
Notes
M+S
Indications of tire damage or other vehicle de‐
fects:
Winter and all-season tires with better cold
weather performance than summer tires.
▷
▷
Unusual vibrations during driving.
Unusual handling such as a strong tendency
to pull to the left or right.
249
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
In case of tire damage
Approved wheels and tires
If there are indications of tire damage, re‐
duce your speed immediately and have the
wheels and tires checked right away; otherwise,
there is the increased risk of an accident.
The manufacturer of your vehicle recom‐
mends that you use only wheels and tires that
have been approved for your particular vehicle
model.
Drive carefully to the next service center or tire
shop.
For example, despite having the same official
size ratings, variations can lead to body contact
and with it, the risk of severe accidents.
If necessary, have the vehicle towed.◀
The manufacturer of your vehicle cannot evalu‐
ate non-approved wheels and tires to determine
if they are suited for use, and therefore cannot
ensure the operating safety of the vehicle if they
are mounted.◀
Repair of tire damage
For safety reasons, the manufacturer of
your vehicle recommends that you do not have
damaged tires repaired; they should be re‐
placed. Otherwise, damage can occur as a re‐
sult.◀
Recommended tire brands
Changing wheels and tires
Mounting
Information on mounting tires
Have mounting and balancing performed
only by a service center or tire specialist.
If this work is not carried out properly, there is
the danger of subsequent damage and related
safety hazards.◀
For each tire size, the manufacturer of your ve‐
hicle recommends certain tire brands. These
can be identified by a star on the tire sidewall.
With proper use, these tires meet the highest
standards for safety and handling.
Wheel and tire combination
Information on the correct wheel-tire combina‐
tion and rim versions for your vehicle can be ob‐
tained from your service center.
New tires
Due to technical factors associated with their
manufacture, tires do not achieve their full trac‐
tion potential until after an initial breaking-in pe‐
riod.
Incorrect wheel and tire combinations impair the
function of a variety of systems such as ABS or
DSC.
To maintain good handling and vehicle re‐
sponse, use only tires with a single tread con‐
figuration from a single manufacturer.
Drive conservatively for the first 200 miles/
300 km.
Following tire damage, have the original wheel
and tire combination remounted on the vehicle
as soon as possible.
Retreaded tires
The manufacturer of your vehicle does not rec‐
ommend the use of retreaded tires.
250
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Retreaded tires
Run-flat tires*
Possibly substantial variations in the de‐
sign and age of the tire casing structures can
limit service life and have a negative impact on
road safety.◀
Label
Winter tires
The manufacturer of your vehicle recommends
winter tires for winter roads or at temperatures
below +45 ℉/+7 ℃.
Although so-called all-season M+S tires do pro‐
vide better winter traction than summer tires,
they do not provide the same level of perform‐
ance as winter tires.
RSC label on the tire sidewall.
The wheels are composed of special rims and
tires that are self-supporting, to a limited de‐
gree.
Maximum speed of winter tires
If the maximum speed of the vehicle is higher
than the permissible speed for the winter tires,
then display a corresponding sign in the field of
vision. You can obtain this sign from the tire spe‐
cialist or from your service center.
The support of the sidewall allows the tire to re‐
main drivable to a restricted degree in the event
of a pressure loss.
Continued driving with a damaged tire., refer to
page 93
Maximum speed for winter tires
Do not exceed the maximum speed for the
winter tires; otherwise, tire damage and acci‐
dents can occur.◀
Changing run-flat tires
For your own safety, only use run-flat tires. No
sparetireisavailableinthecaseofaflattire. Your
service center will be glad to advise you.
Run-flat tires
For your own safety, only use run-flat tires. No
sparetireisavailableinthecaseofaflattire. Your
service center will be glad to advise you.
Snow chains
Fine-link snow chains
Rotating wheels between axles
Only certain types of fine-link snow chains have
been tested by the manufacturer of your vehicle,
classified as road-safe and recommended.
The manufacturer of your vehicle advises
against swapping wheels between the front and
rear axles.
Consult your service center for more informa‐
tion.
This can impair the handling characteristics.
Use
Storage
Use only in pairs on the rear wheels, equipped
with the tires of the following size:
Store wheels and tires in a cool, dry place with
as little exposure to light as possible.
▷
▷
245/50 R 18.
245/45 R 19.
Always protect tires against all contact with oil,
grease and fuels.
Do not exceed the maximum tire inflation pres‐
sure indicated on the side wall of the tire.
Follow the chain manufacturer's instructions.
251
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Make sure that the snow chains are always suf‐
ficiently tight. Retighten as needed according to
the chain manufacturer's instructions.
At speeds above 30 mph/50 km/h, a Check
Control message is displayed. Deactivate
the status manually.
Do not initialize the Tire Pressure Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
If not functioning properly:
▷
Snow chains are mounted. The setting is not
activated
.
When driving with snow chains, briefly activate
Dynamic Traction Control if necessary.
A Check Control message is not displayed.
The automatic detection system is malfunc‐
tioning. Activate the status manually.
Maximum speed with snow chains
Do not exceed a speed of 30 mph/50 km/h when
using snow chains.
Activating/deactivating rear axle
steering
If the status indicating that snow chains are in
use is activated, the rear axle steering is deacti‐
vated automatically.
Snow chain detection*
The concept
When using snow chains, you should set
whether you are driving with or without snow
chains via the iDrive.
At speeds above 30 mph/50 km/h, the rear axle
steering is activated again, even though snow
chains are in use.
The snow chain detection system supports you
by automatically showing the detected state on
the Control Display.
When snow chains are in use, the rear axle steer‐
ing of the Integral Active Steering* is deacti‐
vated automatically.
At speeds above the maximum allowable speed
with snow chains of 30 mph/50 km/h, the rear
axle steering is activated again automatically.
Activating the status
1. "Settings"
2. "Tire chains"
3. "Tire chains installed"
Automatic detection
If functioning properly:
▷
Snow chains are mounted. The setting is not
activated
.
After you drive a short distance, a Check
Control message is shown and the state is
activated automatically.
Confirm the automatic activation.
▷
Snow chains are not mounted. The setting
is activated
.
252
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Engine compartment
Important features in the engine compartment
1
2
3
4
Vehicle identification number*
Jump starting, negative terminal
Washer fluid reservoir
5
6
Oil filler neck. 760i/Li: filler neck is located
under a flap.
Coolant reservoir, removed 760i/Li.
Jump starting, positive terminal
Never reach into the engine compartment
Never reach into the intermediate spaces
Hood
Opening the hood
or gaps in the engine compartment. Otherwise,
there is risk of injury, e.g. from rotating or hot
parts.◀
Working in the engine compartment
Never attempt to perform any service or
repair operations on your vehicle without the
necessary professional technical training.
1. Pull the lever.
If you are unfamiliar with the statutory guide‐
lines, have any work on the vehicle performed
only by a service center.
If this work is not carried out properly, there is
the danger of subsequent damage and related
safety hazards.◀
253
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
2. Press the release handle and open the hood.
3. Be careful of protruding parts on the hood.
Danger of injury when the hood is open
Danger of pinching
Make sure that the closing path of the
hood is clear; otherwise, injuries may result.◀
There is a danger of injury from protruding
parts when the hood is open.◀
Closing the hood
Let the hood drop from a height of approx. 16 in/
40 cm and push down on it to lock it fully.
The hood must audibly engage on both sides.
Hood open when driving
If you see any signs that the hood is not
completely closed while driving, pull over imme‐
diately and close it securely.◀
254
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Engine oil
Duration while driving: approx. 5 minutes.
General information
The engine oil consumption is dependent on the
driving style and driving conditions.
▷
▷
"Engine oil level below minimum. Add 1
quart!"
Add oil within the next 125 miles/200 km.
Therefore, check the engine oil level after every
refueling using the electronic engine oil level
check.
"Engine oil level too high! Have this
checked."
Have the vehicle checked immediately.
Too much engine oil
Checking the oil level
Have the vehicle checked immedi‐
ately; otherwise, surplus oil can lead to en‐
gine damage.◀
The concept
The oil level is monitored electronically and dis‐
played on the Control Display.
▷
"Measurement inactive. Have this
checked."
Requirements
Note the newly calculated remaining mile‐
age until the next oil service. Have the sys‐
tem checked as soon as possible.
▷
The engine must be running and warm after
the vehicle has been driven for at least
6 miles/10 km.
▷
The vehicle is stopped or being driven on a
level roadway.
Adding engine oil
760i/Li: open/close flap
Displaying the oil level
1. "Vehicle Info"
2. "Vehicle status"
3. "Engine oil level"
When the flap is closed, it must latch
Possible messages
▷
▷
▷
"Engine oil level OK"
"Measurement not possible at this time."
"Measuring engine oil level..."
Duration with the engine running: ap‐
prox. 3 minutes.
255
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Filler neck
When the indicator lights up in the instrument
cluster, add 1 US quart/liter of engine oil within
the next 125 miles/200 km.
Coolant
General information
Recommended oil types, refer to page 256.
Protect children
Danger of burns from hot engine
Do not open the cooling system while the
engine is hot; otherwise, escaping coolant may
cause burns.◀
Keep oil, grease, etc., out of reach of chil‐
dren and heed the warnings on the containers
to prevent health risks.◀
Suitable additives
Only use suitable additives; otherwise, en‐
gine damage may occur. The additives are
harmful to your health.◀
Oil types
Coolant consists of water and additives.
Note
Not all commercially available additives are suit‐
able for your vehicle. Ask your service center for
suitable additives.
No oil additives
Oiladditivesmayleadtoenginedamage.◀
Approved oil types
Coolant level
Your service center can advise you on which en‐
gine oils have been approved by the manufac‐
turer of your vehicle.
If there is no Min– and Max– mark in the filler
neck of the coolant reservoir, have the coolant
level checked if necessary by your service cen‐
ter and add coolant as needed.
The engine oil quality is critical for the life of the
engine.
Only use approved BMW High Performance oil.
Approved oils belong to the viscosity grades
SAE 0W-40, SAE 0W-30, SAE 5W-40 and SAE
5W-30.
Alternative oil types
If the approved engine oils are not available, up
to 1 US quart/liter of another oil with the follow‐
ing specification may be used.
API SM quality standards or higher.
256
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Checking
1. Let the engine cool.
2. Turn the cap of the coolant reservoir slightly
counterclockwise to allow any excess pres‐
sure to dissipate, and then open it.
3. The coolant level is correct if it lies between
the minimum and maximum marks in the
filler neck.
4. If the coolant is low, slowly add coolant up to
the specified level; do not overfill.
5. Turn the cap until there is an audible click.
6. Have the cause of the coolant loss elimi‐
nated as soon as possible.
Disposal
Comply with the relevant environmental
protection regulations when disposing
of coolant and coolant additives.
257
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Maintenance
BMW Maintenance System
Service and Warranty
Information Booklet for US
models and Warranty and
Service Guide Booklet for
Canadian models
The maintenance system directs you to re‐
quired maintenance measures and thereby sup‐
ports you in maintaining road safety and the op‐
erational reliability of the vehicle.
Please consult your Service and Warranty Infor‐
mation Booklet for US models and Warranty and
Service Guide Booklet for Canadian models for
additional information on service requirements.
Condition Based Service CBS
Sensors and special algorithms take into ac‐
count the driving conditions of your vehicle.
Based on this, Condition Based Service deter‐
mines the maintenance requirements.
Maintenance and repair should be performed by
your service center. Make sure to have regular
maintenance procedures recorded in the vehi‐
cle's Service and Warranty Information Booklet
for US models, and in the Warranty and Service
Guide Booklet for Canadian models. These en‐
tries are proof of regular maintenance.
The system makes it possible to adapt the
amount of maintenance you need to your user
profile.
Details on the service requirements, refer to
page 81, can be displayed on the Control Dis‐
play.
Socket for OBD Onboard
Diagnosis
Service data in the remote control
Information on the required maintenance is con‐
tinuously stored in the remote control. Your
service center will read out this data and suggest
the right array of service procedures for your ve‐
hicle.
Therefore, hand your service specialist the re‐
mote control that you used most recently.
Storage periods
Storage periods during which the vehicle bat‐
tery was disconnected are not taken into ac‐
count.
There is an OBD socket on the driver's side for
checking the primary components in the vehicle
emissions.
If this occurs, have a service center update the
time-dependent maintenance procedures,
such as checking brake fluid and, if necessary,
changing the engine oil and the microfilter/acti‐
vated-charcoal filter.
Emissions
▷
The warning lamp lights up:
Emissions are deteriorating. Have
the vehicle checked as soon as pos‐
sible.
▷
The warning lamp flashes under cer‐
tain circumstances:
258
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
This indicates that there is excessive
misfiring in the engine.
Reduce the vehicle speed and have
the system checked immediately;
otherwise, serious engine misfiring
within a brief period can seriously
damage emission control compo‐
nents, in particular the catalytic con‐
verter.
Fuel cap
The indicator lamp lights up.
If the fuel cap is not properly tightened,
the OBD system may conclude that fuel
vapor is escaping. If the cap is then tightened,
the display should go out in a short time.
Data memory
Your vehicle records data relating to vehicle op‐
eration, faults and user settings. These data are
stored in the remote control and can be read out
with suitable devices, particularly when the ve‐
hicle is serviced. The data obtained in this way
provide valuable information for service proc‐
esses and repair or for optimizing and develop‐
ing vehicle functions further.
In addition, if you signed a service contract for
Assist, certain vehicle data can be sent directly
from the vehicle to facilitate the desired serv‐
ices.
259
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Replacing components
3. Position the wiper blade in a horizontal po‐
Tool kit
sition.
4. Remove the wiper blade toward one side.
The tool kit is located in a fold-down cover in the
trunk lid.
Unscrew the wing nut to open.
Lamp and bulb replacement
Wiper blade replacement
General information
Lamps and bulbs make an essential contribution
to vehicle safety.
Do not fold down the wipers without wiper
blades
The manufacturer of your vehicle recommends
that you entrust corresponding procedures to
your service center if you are unfamiliar with
them or they are not described here.
Do not fold down the wipers if wiper blades have
not been installed; this may damage the wind‐
shield.◀
You can obtain a selection of replacement bulbs
at your service center.
Replacing the wiper blades
1. To change the wiper blades, fold up, refer to
page 72, the wiper arms.
Danger of burns
2. Fold up the wipers.
Only change bulbs when they are cool;
otherwise, there is the danger of getting
burned.◀
Working on the lighting system
When working on the lighting system, you
should always switch off the lights affected to
prevent short circuits.
To avoid possible injury or equipment damage
when replacing bulbs, observe any instructions
provided by the bulb manufacturer.◀
260
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Do not touch the bulbs
3
4
Low beams/high beams
Turn signal
Do not touch the glass of new bulbs with
your bare hands, as even minute amounts of
contamination will burn into the bulb's surface
and reduce its service life.
Xenon lamps
Because of the long life of these bulbs, the like‐
lihood of failure is very low. Switching the lamps
on and off frequently shortens their life.
Use a clean tissue, cloth or something similar, or
hold the bulb by its base.◀
If a xenon bulb fails, switch on the front fog lamps
and continue the trip with great care. Comply
with local regulations.
Light-emitting diodes (LEDs)
Light-emitting diodes installed behind a cover
serve as the light source for controls, display el‐
ements and other equipment.
Do not perform work/bulb replacement on
xenon headlamps
These light-emitting diodes, which are related
to conventional lasers, are officially designated
as Class 1 light-emitting diodes.
Have any work on the xenon lighting system, in‐
cluding bulb replacement, performed only by a
service center.
Do not remove the covers
Due to the high voltage present in the system,
there is the danger of fatal injuries if work is car‐
ried out improperly.◀
Do not remove the covers, and never stare
into the unfiltered light for several hours; other‐
wise, irritation of the retina could result.◀
For checking and adjusting headlamp aim,
please contact your BMW center.
Headlamp glass
Condensation can form on the inside of the ex‐
ternal lamps in cool or humid weather. When the
light is switched on, the condensation evapo‐
rates after a short time. The headlamp glasses
do not need to be changed.
Turn signals, incl. side indicators
Follow the general instructions on lamps and
bulbs, refer to page 260.
These lamps are made using LED technology.
Please contact your service center in the event
of a malfunction.
If there is a large amount of moisture, e.g., water
droplets form in the lamp, have it checked by
your service center.
Adaptive light control
Follow the general instructions on lamps and
bulbs, refer to page 260.
Front lamps, bulb replacement
At a glance
The illustration shows the left side of the engine
compartment.
55-watt bulb, H3.
1
2
Adaptive light control
Parking lamp, daytime running lights*
261
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
1. Open the folding cover in the engine com‐
partment.
1. Open the folding cover in the engine com‐
partment.
2. Turn the cap and remove it.
2. Turn the cap and remove it.
3. Squeeze the holder together and guide it
downward.
3. Turn the bulb holder.
Turn in the other direction on the right side.
4. Release the holder and fold it upward.
5. Remove the bulb and replace it.
4. Remove the bulb and replace it.
5. Insert the new bulb and attach the cover in
the reverse order.
6. Insert the new bulb and attach the cover in
the reverse order.
Front fog lamps
Follow the general instructions on lamps and
bulbs, refer to page 260.
Parking lamps
Follow the general instructions on lamps and
bulbs, refer to page 260.
35-watt bulb, H8.
The illustration shows the left side of the engine
compartment.
35-watt bulb, H8.
262
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Turn signal, brake, tail, and license
plate lamps
1. Snap out the grill at the recess, arrow.
Follow the general instructions on lamps and
bulbs., refer to page 260
These lights are made using LED technology.
Contact your service center in the event of a
malfunction.
Lamps in the trunk lid
Follow the general instructions on lamps and
bulbs., refer to page 260
2. Remove the screw using a screw driver.
Access to the lamps
1. Remove the three screws using the screw
driver from the tool kit.
3. Pull the lamp out toward the front.
4. Remove the bulb and replace it.
5. Insert the new bulb and attach the cover in
the reverse order.
2. Fold away the cover.
Tail lamps, bulb replacement
At a glance
3. Replace the defective bulb.
1
2
3
4
5
6
Turn signal
Backup lamp
Inside brake lamp*
Tail lamp
Outside brake lamp
Rear reflector*
263
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Inside brake lamp*
Jacking points for the vehicle jack
21-watt bulb, H21W.
The jacking points for the vehicle jack are lo‐
cated in the positions shown.
Pull out the bulb and replace it.
Lug bolt lock*
Backup lamp
16-watt bulb, W16W.
The lug bolt lock is in the tool kit or in a storage
compartment close to the tool kit.
Pull out the bulb and replace it.
Changing wheels
Notes
The vehicle equipment does not include a spare
tire.
When using run-flat tires* or tire sealants, a tire
does not need to be changed immediately in the
event of pressure loss due to a flat tire.
▷
▷
Lug bolt, arrow 1.
Adapter, arrow 2.
The tools for changing wheels are available as
accessories from your service center.
Removing
1. Attach the adapter to the wheel lug.
2. Unscrew the lug bolt.
Remove the adapter after screwing the lug bolt
back on.
264
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Vehicle battery
Fuses
Maintenance
Notes
The battery is maintenance-free, i.e., the elec‐
trolyte will last for the life of the battery.
Replacing fuses
Never attempt to repair a blown fuse and
do not replace a defective fuse with a substitute
of another color or amperage rating; this could
lead to a circuit overload, ultimately resulting in
a fire in the vehicle.◀
Your service center will be glad to advise you on
questions regarding the battery.
Battery replacement
Use approved vehicle batteries only.
Plastic tweezers and information on the fuse
types and locations are stored in the fuse box in
the cargo area.
Only use vehicle batteries that have been
approved for your vehicle by the manufacturer;
otherwise, the vehicle could be damaged and
systems or functions may not be fully availa‐
ble.◀
In the glove compartment
After a battery replacement, have the battery
registered on the vehicle by your service center
to ensure that all comfort functions are fully
available.
Charging the battery
In the vehicle, only charge the battery via the
terminals, refer to page 268, in the engine com‐
partment with the engine off.
Push the handle up, arrow 1, and open the lid,
arrow 2.
Power failure
After a temporary power loss, some equipment
needs to be reinitialized.
In the cargo area
Individual settings need to be reprogrammed:
▷
Seat, mirror, and steering wheel memory:
store the positions again.
▷
▷
▷
▷
Time: update.
Date: update.
Radio station: save again.
Navigation system: wait for the operability of
the navigation.
Open the cover on the right side trim.
Information on the fuse types and locations is
found on a separate sheet.
Disposing of old batteries
Have old batteries disposed of by your
service center or bring them to a recy‐
cling center.
Maintain the battery in an upright position for
transport and storage. Secure the battery so
that it does not tip over during transport.
265
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Breakdown assistance
▷
Under certain circumstances, the system
can be reactivated by a service center after
you sign a new contract.
Hazard warning flashers
Initiating an Emergency Request
The button is located in the center console.
Emergency Request*
1. Press the cover briefly to open it.
2. Press the SOS button until the LED in the
button lights up.
Requirements
▷
Equipment version with full preparation
package mobile phone.
▷
The LED lights up: an Emergency Request
was initiated.
An Emergency Request can be made, even
if no mobile phones are paired with the ve‐
hicle.
If the situation allows, wait in your vehicle
until the voice connection has been estab‐
lished.
▷
▷
▷
BMW Assist is activated.
▷
The LED flashes if the connection to the
BMW Assist Response Center has been es‐
tablished.
The radio ready state is switched on.
The BMW Assist system is logged in to a
wireless communications network sup‐
ported by BMW Assist.
After the Emergency Request arrives at the
BMW Assist Response Center, the BMW
Assist Response Center contacts you and
takes further steps to help you.
▷
The Assist system is functional.
Only press the SOS button in an emergency.
Emergency Request not guaranteed
Even if you are unable to respond, the BMW
Assist Response Center can take further
steps to help you under certain circumstan‐
ces.
For technical reasons, the Emergency Re‐
quest cannot be guaranteed under unfavorable
conditions.◀
For this purpose, data that are used to de‐
termine the necessary rescue measures,
such as the current position of the vehicle if
it can be established, are transmitted to the
BMW Assist Response Center.
Service contract
▷
After your contract with BMW Assist has ex‐
pired, the BMW Assist system can be deac‐
tivated by the service center without you
having to visit a workshop.
▷
If the LED is flashing but the BMW Assist
Response Center cannot be heard on the
hands-free system, the hands-free system
may be malfunctioning. However, the BMW
After deactivation, an Emergency Request
is no longer possible.
266
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Assist Response Center may still be able to
hear you.
Roadside Assistance
Service availability
Initiating an Emergency Request
automatically
Under certain conditions, an Emergency Re‐
questisautomaticallyinitiatedimmediatelyafter
a severe accident. Automatic Collision Notifica‐
tion is not affected by pressing the SOS button.
Roadside Assistance can be reached around the
clock in many countries. You can obtain assis‐
tance there in the event of a vehicle breakdown.
Roadside Assistance
The Roadside Assistance, refer to page 235
phone number can be viewed on the iDrive or a
connection to Roadside Assistance* can be es‐
tablished directly.
Warning triangle*
Jump starting
Notes
If the battery is discharged, an engine can be
started using the battery of another vehicle and
two jumper cables. Only use jumper cables with
fully insulated clamp handles.
The warning triangle is located in the container
on the inside of the trunk lid.
To prevent personal injury or damage to both
vehicles, adhere strictly to the following proce‐
dure.
Unscrew the wing nut to open.
Do not touch live parts
To avoid the risk of potentially fatal injury,
always avoid all contact with electrical compo‐
nents while the engine is running.◀
First aid kit*
Preparation
1. Check whether the battery of the other ve‐
hicle has a voltage of 12 volts. This informa‐
tion can be found on the battery.
2. Switch off the engine of the assisting vehi‐
cle.
3. Switch off any electronic systems/power
consumers in both vehicles.
The first aid kit is located in the container on the
inside of the trunk lid.
Bodywork contact between vehicles
Unscrew the wing nut to open.
Make sure that there is no contact be‐
tween the bodywork of the two vehicles; other‐
wise, there is the danger of short circuits.◀
Some of the articles have a limited service life.
Check the expiration dates of the contents reg‐
ularly and replace any items promptly.
267
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
body ground of the vehicle providing assis‐
tance.
Starting aid terminals
Connecting order
5. Attach the other end of the cable to the neg‐
ative terminal of the battery, or to the corre‐
sponding engine or body ground of the ve‐
hicle to be started.
Connect the jumper cables in the correct
order; otherwise, there is the danger of injury
from sparking.◀
Starting the engine
Never use spray fluids to start the engine.
1. Start the engine of the assisting vehicle and
let it run for several minutes at an increased
idle speed.
If the vehicle being started has a diesel en‐
gine: let the engine of the assisting vehicle
run for approx. 10 minutes.
The so-called starting aid terminal in the engine
compartment acts as the battery's positive ter‐
minal.
2. Start the engine of the vehicle being started
in the usual way.
If the first starting attempt is not successful,
wait a few minutes before making another
attempt in order to allow the discharged bat‐
tery to recharge.
3. Let both engines run for several minutes.
4. Disconnect the jumper cables in the reverse
order.
Check the battery and recharge if necessary.
The body ground or a special nut acts as the
negative terminal.
Tow-starting and towing
Transporting your vehicle
Note
Your vehicle is not permitted to be towed.
Therefore, contact a service center in the event
of a breakdown.
Connecting the cables
1. Pull off the cap of the BMW starting aid ter‐
minal.
2. Attach one terminal clamp of the positive
jumper cable to the positive terminal of the
battery, or to the corresponding starting aid
terminal of the vehicle providing assistance.
Do not have the vehicle towed
Have your vehicle transported on a loading
platform only; otherwise, damage may occur.◀
3. Attach the other end of the cable to the pos‐
itive terminal of the battery, or to the corre‐
sponding starting aid terminal of the vehicle
to be started.
4. Attach one terminal clamp of the negative
jumper cable to the negative terminal of the
battery, or to the corresponding engine or
268
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Tow truck
Towing methods when towing other
vehicles
Tow bar
The tow fittings used should be on the same
side on both vehicles.
Should it prove impossible to avoid mounting
the tow bar at an offset angle, please observe
the following:
▷
Maneuvering capability is limited during cor‐
nering.
Do not lift the vehicle
▷
The tow bar will generate lateral forces if it
is secured with an offset.
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage may
result.◀
Tow rope
When starting to tow the vehicle, make sure that
the tow rope is taut.
Tow-starting
Do not tow-start the vehicle.
To avoid jerking and the associated stresses on
the vehicle components when towing, always
use nylon ropes or nylon straps.
Due to the automatic transmission, the engine
cannot be started by tow-starting.
Have the cause of the starting difficulties rem‐
edied.
Attaching the tow rope correctly
Only secure the tow rope on the tow fit‐
ting; otherwise, damage can occur when it is se‐
cured on other parts of the vehicle.◀
Towing other vehicles
General information
Tow fitting
Light towing vehicle
Your vehicle must not be lighter than the
vehicle being towed; otherwise, it will not be
possible to control vehicle response.◀
Attaching the tow bar/tow rope correctly
Attach the tow bar or tow rope to the tow
fitting; connecting it to other vehicle parts may
cause damage.◀
▷
Switch on the hazard warning system, de‐
pending on local regulations.
The screw-in tow fitting should always be car‐
ried in the vehicle. It can be screwed in at the
front or rear of the BMW. It is located in the con‐
tainer on the inside of the trunk lid.
▷
If the electrical system has failed, clearly
identify the vehicle being towed by placing
a sign or a warning triangle in the rear win‐
dow.
Tow fitting, information on use
▷
Use only the tow fitting provided with
the vehicle and screw it all the way in.
269
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
▷
▷
▷
Use the tow fitting for towing on paved roads
only.
Use the tow fitting screwed in at the front for
maneuvering the vehicle only.
Avoid lateral loading of the tow fitting, e.g.,
do not lift the vehicle by the tow fitting.
Otherwise, damage to the tow fitting and the ve‐
hicle can occur.◀
Screw thread
Push out the cover by pressing on the arrow
symbol.
270
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Care
▷
▷
Deactivate the rain sensor, refer to page 71,
to avoid unintentional wiper activation.
Car washes
Notes
In some cases, an unintentional alarm can be
triggeredbytheinteriormotionsensorofthe
alarm system*. Follow the instructions on
avoiding an unintentional alarm, refer to
page 44.
Steam jets or high-pressure washers
When using steam jets or high-pressure
washers, hold them a sufficient distance away
and use a maximum temperature of 140 ℉/
60 ℃.
Guide rails in car washes
Avoid car washes with guide rails higher
than 4 in/10 cm; otherwise, the vehicle body
could be damaged.◀
Holding them too close or using excessively
high pressures or temperatures can cause dam‐
age or preliminary damage that may then lead to
long-term damage.
Before driving into a car wash
The vehicle is able to roll when the following
steps are taken:
Follow the operating instructions for the high-
pressure washer.◀
Cleaning sensors/cameras with high-
pressure washers
1. Depress the brake pedal.
2. Engage transmission position N.
When using high-pressure washers, do not
spray the exterior sensors and cameras, e.g.,
Park Distance Control*, for extended periods of
time and only from a distance of at least 12 in/
30 cm.◀
3. Release the parking brake, refer to page 66,
or deactivate Automatic Hold, refer to
page 68.
4. Switch the engine off.
Wash your vehicle frequently, particularly in win‐
ter.
Transmission position P with the igni‐
tion off
Intense soiling and road salt can damage the ve‐
hicle.
When the ignition is switched off, position P
is engaged automatically. When in an auto‐
matic car wash, for example, ensure that the
ignition is not switched off accidentally.◀
Washing in automatic car washes
Your vehicle can be washed in automatic car
washes right from the start.
The vehicle cannot be locked from the outside
when in transmission position N.
Give preference to cloth car washes or those
that use soft brushes in order to avoid paint
damage.
A signal is sounded when an attempt is made to
lock the vehicle.
Transmission position
Transmission position P is engaged automati‐
cally:
Notes
Note the following:
▷
Make sure that the wheels and tires are not
damaged by the transport mechanisms.
▷
▷
When the ignition is switched off.
After approx. 15 minutes.
▷
Fold in the exterior mirrors; otherwise, they
may be damaged, depending on the width of
the vehicle.
271
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
wear and premature degradation of the leather
surface.
Headlamps
▷
Do not rub dry and do not use abrasive or
caustic cleansers.
To guard against discoloration, such as from
clothing, provide leather care roughly every two
months.
▷
Soak areas that have been soiled e.g. due to
insects, with shampoo and wash off with
water.
Clean light-colored leather more frequently as
dust and dirt are more noticeable.
▷
Thaw ice with de-icing spray; do not use an
ice scraper.
Use leather care products; otherwise, dirt and
grease will gradually break down the protective
layer of the leather surface.
After washing the vehicle
After washing the vehicle, apply the brakes
briefly to dry them; otherwise, braking action can
be reduced and corrosion of the brake discs can
occur.
Suitable care products are available from the
service center.
Upholstery material care
Vacuum regularly with a vacuum cleaner.
If they are very dirty, e.g., beverage stains, use a
soft sponge or microfiber cloth with a suitable
interior cleaner.
Vehicle care
Car care products
Clean the upholstery down to the seams using
large sweeping motions. Avoid rubbing the ma‐
terial vigorously.
BMW recommends using cleaning and care
products from BMW, since these have been
tested and approved.
Damage from Velcro® fasteners
Car care and cleaning products
Open Velcro® fasteners on pants or other
articles of clothing can damage the seat covers.
Ensure that any Velcro® fasteners are closed.◀
Follow the instructions on the container.
When cleaning the interior, open the doors or
windows.
Only use products intended for cleaning vehi‐
cles.
Caring for special components
Light-alloy wheels
Use wheel cleaner, particularly during the winter
months. Do not use aggressive, acidic, strongly
alkaline or abrasive cleaners, or steam jets
above 140 ℉/60 ℃; follow the manufacturer's
instructions.
Cleansers can contain substances that are dan‐
gerous and harmful to your health.◀
Vehicle paint
Regular care contributes to driving safety and
value retention.
Environmental influences can act on the vehicle
paint. Tailor the frequency and extent of your car
care to these influences.
Chrome surfaces*
Carefully clean components such as the radiator
grille or door handles with an ample supply of
water, possibly with shampoo added, particu‐
larly when they have been exposed to road salt.
Leather care
Remove dust from the leather often, using a
cloth or vacuum cleaner.
Rubber components
Aside from water, treat only with rubber cleans‐
ers.
Otherwise, particles of dust and road grime
chafe in pores and folds, and lead to increased
272
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
When cleaning rubber seals, do not use any sil‐
icon-containing car care products in order to
avoid damage or reduced noise damping.
Floor carpets and floor mats*
No objects in the area around the pedals
Keep floor mats, carpets, and any other
objects out of the area of motion of the pedals;
otherwise, the function of the pedals could be
impeded while driving
Fine wood parts*
Clean fine wood facing and fine wood compo‐
nents only with a moist rag. Then dry with a soft
cloth.
Do not place additional floor mats over existing
mats or other objects.
Only use floor mats that have been approved for
the vehicle and can be properly fixed in place.
Plastic components
These include:
Ensure that the floor mats are securely fastened
again after they were removed for cleaning, for
example.◀
▷
▷
▷
▷
▷
Imitation leather surfaces.
Headliner.
Lamp lenses.
Floor mats can be removed from the passenger
compartment for cleaning.
Instrument cluster cover.
Matte black spray-coated components.
If the floor carpets are very dirty, clean with a
microfiber cloth and water or a textile cleaner. To
prevent matting of the carpet, rub back and forth
in the direction of travel only.
Clean with a microfiber cloth.
Moisten the cloth lightly and use plastic
cleanser, if necessary.
Do not soak the headliner.
Sensors/cameras
To clean sensors and cameras, use a cloth mois‐
tened with a small amount of glass cleaner.
Do not use cleansers that contain alcohol
or solvents
Do not use cleansers that contain alcohol or sol‐
vents, such as lacquer thinners, heavy-duty
grease removers, fuel, or such; this could lead to
surface damage.◀
Displays/screens
Clean the displays with a microfiber cloth.
Cleaning displays
Do not use chemical or household cleans‐
ers.
Safety belts
Dirty belt straps impede the reeling action and
thus have a negative impact on safety.
Keep all fluids and moisture away from the unit.
Otherwise, they could affect or damage surfa‐
ces or electrical components.
Chemical cleaning
Do not clean chemically; this can destroy
the webbing.◀
Avoid pressing too hard when cleaning and do
not use abrasive materials; otherwise, damage
can result.◀
Use only a mild soapy solution, with the safety
belts clipped into their buckles.
Do not allow the reels to retract the safety belts
until they are dry.
Long-term vehicle storage
Your service center can advise you on what to
consider when storing the vehicle for longer
than three months.
273
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
Online Edition for Part no. 01 40 2 606 497 - 03 11 490
