Deutsch
EnglishPractical information -> Charging the traction battery (Electric) for your Peugeot 2008 2019-2025
Practical information
Accelerated charging, mode 3
Fast charging, mode 4
For a full charge, follow the desired charging
procedure without pausing it, until it ends
automatically. Charging can be either immediate
or deferred (except fast public charger, mode 4).
You can stop domestic or accelerated charging
at any time by unlocking the vehicle and
removing the nozzle. For superfast charging,
refer to the fast public charger.
7
Accelerated charging unit (Wallbox)
(accelerated charging - single-phase or three-
phase alternating current (AC))
Public fast charger
(superfast charging - direct current (DC))
For more information on the charging displays
on the Instrument panel and the Touch screen,
refer to the corresponding section.
Depending on version, in mode 3 with an
accelerated charging unit (Wallbox): 32 A
maximum charging current.
It is also possible to monitor the charging
progress using the MYPEUGEOT APP
application.
For more information on Remote functions,
refer to the corresponding section.
Charging cable, mode 4 (DC)
(integrated into the public fast charger)
Charging cable, mode 3 (AC)
As a safety measure, the engine will not
start if the charging cable is plugged into
the connector on the vehicle. A warning is
displayed on the instrument panel.
Only use public fast chargers where the cable
length does not exceed 30 metres.
Cooling the traction battery
The cooling fan in the engine
compartment comes on during charging to
cool the on-board charger and the traction
battery.
Accelerated charging unit (Wallbox)
Do not disassemble or modify the
charging unit - risk of electrocution and/or fire!
Refer to the charging unit manufacturer's user
manual for the operating instructions.
Charging the traction
battery (Electric)
To recharge, connect the vehicle to a domestic
electricity supply (domestic or accelerated
charging) or to a fast public charger (superfast
charging).
143
Practical information
Vehicle in storage for more than 1
Commission on Non-Ionizing Radiation
Protection (ICNIRP - 1998 Guidelines).
If no action is taken on one of the openings
(door or boot) or on the charging nozzle, the
vehicle will lock again after 30 seconds and
charging will resume automatically.
Never work under the bonnet:
– Some areas remain very hot, even an hour
after charging ends - risk of burns!
– The fan may start at any time - risk of cuts
or strangulation!
month
Discharge the traction battery down to 2 or
3 bars on the charge level indicator on the
instrument panel.
If in doubt
Domestic or accelerated charging: do
not remain inside or near the vehicle, or near
the charging cable or charging unit, even for
a short time.
Superfast charging: do not use the system
yourself and avoid approaching public fast
charging points. Leave the area and ask a
third party to recharge the vehicle.
Do not connect the charging cable.
Always park the vehicle in a place with
temperatures between -10°C and 30°C
(parking in a place with extreme temperatures
can damage the traction battery).
Disconnect the cable from the (+) terminal
of the accessory battery in the engine
compartment.
Connect a 12 V battery charger to the (+)
and (-) terminals of the accessory battery
about every 3 months in order to recharge the
accessory battery and maintain an operating
voltage.
After charging
Check that the charging flap is closed.
Do not leave the cable connected to the
domestic power socket - risk of short-circuit
or electrocution in the event of contact with or
immersion in water!
For domestic or accelerated charging
Before charging
Depending on the context:
► Have a professional check that the
electrical system to be used complies with
applicable standards and is compatible with
the vehicle.
► Have a professional electrician install
a dedicated domestic power socket or
accelerated charging unit (Wallbox)
compatible with the vehicle.
You should preferably use the charging cable
available as an accessory.
For more information, contact a PEUGEOT
dealer or a qualified workshop.
For superfast charging
Before charging
Precautions
Check that the fast public charging
station and its charging cable are compatible
with the vehicle.
If the exterior temperature is below:
– 0°C, charging times may be extended.
– -20°C, charging is still possible, but
charging times may be extended even further
(the battery has to be heated first).
Electric vehicles were developed in accordance
with the guidelines on maximum electromagnetic
fields issued by the International Commission
on Non-Ionizing Radiation Protection (ICNIRP -
1998 Guidelines).
Wearers of pacemakers or equivalent
devices
The electric vehicles have been
developed in accordance with the
guidelines on the maximum levels for
electromagnetic fields issued by the International
After charging
Check that the charging flap is closed.
(During charging)
While charging is in progress, unlocking
the vehicle will cause the charging to stop.
144
Practical information
Superfast charging, mode 4
If this is not the case, charging has not
started; restart the procedure, ensuring that all
connections are properly established.
The red indicator lamp in the flap comes on to
indicate that the nozzle is locked.
Connection
7
► Before charging, check that the drive selector
is in mode P, otherwise charging is not possible.
► Open the charging flap by pressing the
push-button, and check that there are no foreign
bodies on the charging connector.
When charging is complete and while the
charging cable is still connected, opening
the driver's door will display the charge level
on the instrument panel for about 20 seconds.
Domestic charging, mode 2
► Depending on version, remove the protective
cover from the lower part of the connector.
► Follow the instructions for use of the fast
public charger and connect the cable from the
fast public charger to the vehicle's connector.
The start of charging is confirmed by the flashing
green charging indicator lamp in the flap.
If this is not the case, charging has not started;
restart the procedure, ensuring that the
connection is properly established.
Accelerated charging, mode 3
The red indicator lamp in the flap comes on to
indicate that the nozzle is locked.
► Follow the accelerated charging unit
(Wallbox) user instructions.
► Remove the protective cover from the
charging nozzle.
► Connect the charging cable from the control
unit to the domestic socket.
Deferred charging
Settings
► Insert the nozzle into the charging connector.
The start of charging is confirmed when the
charging indicator lamp in the flap flashes green.
If this is not the case, charging has not started;
restart the procedure, ensuring that the
connection has been properly established.
The red indicator lamp in the flap comes on to
indicate that the nozzle is locked.
When the connection is made, all of the indicator
lamps on the control unit light up, then only the
POWER indicator lamp remains on in green.
► Remove the protective cover from the
charging nozzle.
► Insert the nozzle into the charging connector.
The start of charging is confirmed by the flashing
green CHARGE indicator lamps in the flap, then
those on the control unit.
(Depending on country of sale)
On a smartphone or tablet
You can programme the deferred
charging function at any time via the
MYPEUGEOT APP application.
For more information on Remote functions,
refer to the corresponding section.
145
Practical information
In the vehicle, with PEUGEOT Connect
Nav
► Disconnect the control unit end of the
charging cable from the domestic socket.
Disconnection
Accelerated charging, mode 3
Depending on version, the Energy menu can be
accessed either:
The end of charging is indicated by the charging
control unit and by the fixed lighting of the green
indicator lamp in the flap.
► Hang up the nozzle on the charging unit and
close the charging flap.
– directly, by pressing the button near the
touch screen (with 10" touch screen).
– via the Applications menu.
Before disconnecting the nozzle from the
charging connector:
► If the vehicle is unlocked, lock it and then
unlock it.
► If the vehicle is locked, unlock it.
The red indicator lamp in the flap goes out to
confirm that the charging nozzle is unlocked.
► Within 30 seconds, remove the charging
nozzle.
► In the Energy touch screen menu,
select the Charge page.
► Set the charging start time.
► Press OK.
Superfast charging, mode 4
The end of charging is indicated by the charger
and by the fixed lighting of the green indicator
lamp in the flap.
► You can also pause charging by
pressing this button in the flap (in mode 4
only).
► Hang up the nozzle on the charger.
► Depending on version, replace the protective
cover on the lower section and close the
charging flap.
The setting is saved in the system.
Activation
Deferred charging is only possible with
modes 2 and 3.
The charging indicator lamp comes on in white.
With selective door unlocking activated,
press the unlocking button twice to
disconnect the charging nozzle.
► After programming the deferred charging,
connect your vehicle to the desired charging
equipment.
When the charging nozzle is
disconnected, a message on the
instrument panel indicates that charging is
complete, even if the charging nozzle was
disconnected before full charging was
completed.
When charging is complete, the green
charging indicator lamp in the flap goes
out after about 2 minutes.
Domestic charging, mode 2
► Press this button in the flap within one
minute to activate the system (confirmed by the
charging indicator lamp coming on in blue).
The end of charging is confirmed when the green
CHARGE indicator lamp on the control unit and
the green charging indicator lamp in the flap
come on fixed.
► Replace the protective cover on the charging
nozzle and close the charging flap.
Towing device
Load distribution
► Distribute the load in the trailer so that the
heaviest items are as close as possible to the
146
