Deutsch
EnglishPractical Information -> Changing a Bulb for your Peugeot 107 2005-2014
PRACTICAL INFORMATION
9
1. Side lights (W 5 W)
Turn the bulb holder A one quar-
ter of a turn and remove it.
Remove the bulb and change it.
Fold the jack 2 and detach it.
Tighten the wheel bolts using the
wheelbrace 1.
Refit the trim.
Store the tools and the wheel in
the boot.
CHANGING A BULB
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/
Main beam headlamps
After changing a wheel:
- have the tightening of the bolts and
the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel repaired
and refit it on the vehicle as soon
as possible.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
2. Direction indicators
(PY 21 W amber)
Turn the bulb holder B one quar-
condensation on the inter-
Contact a PEUGEOT dealer.
ter of a turn and remove it.
nal face of the headlamps is nor-
mal; it disappears a few minutes after
the lights are switched on.
Turn the bulb one quarter of a turn.
Remove the bulb and change it.
If you encounter any difficulties, con-
tact a PEUGEOT dealer.
70
PRACTICAL INFORMATION
9
1. Side lights (W 5 W)
Turn the bulb holder A one quar-
ter of a turn and remove it.
Remove the bulb and change it.
Fold the jack 2 and detach it.
Tighten the wheel bolts using the
wheelbrace 1.
Refit the trim.
Store the tools and the wheel in
the boot.
CHANGING A BULB
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/
Main beam headlamps
After changing a wheel:
- have the tightening of the bolts and
the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel repaired
and refit it on the vehicle as soon
as possible.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
2. Direction indicators
(PY 21 W amber)
Turn the bulb holder B one quar-
condensation on the inter-
Contact a PEUGEOT dealer.
ter of a turn and remove it.
nal face of the headlamps is nor-
mal; it disappears a few minutes after
the lights are switched on.
Turn the bulb one quarter of a turn.
Remove the bulb and change it.
If you encounter any difficulties, con-
tact a PEUGEOT dealer.
70
PRACTICAL INFORMATION
9
3. Dipped headlamps/
Main beam headlamps
(H4 - 60/55 W)
Disconnect the connector.
Remove the rubber C.
Push the tab D on the side.
Remove the bulb holder and
change the bulb.
Refit the bulb holder, the tab then
the rubber.
If you encounter any difficulties, con-
tact a PEUGEOT dealer.
Rear lights
1. Brake/side lights (P 21/5 W)
2. Direction indicators (P 21 W)
3. Reversing light (P 21 W),
left-hand side
These 3 bulbs are changed by re-
moving the light:
open the boot,
unscrew the two light fixing
nuts A,
remove the light unit by pulling
Fog lamp (P 21 W),
right-hand side
outwards,
71
PRACTICAL INFORMATION
9
3. Dipped headlamps/
Main beam headlamps
(H4 - 60/55 W)
Disconnect the connector.
Remove the rubber C.
Push the tab D on the side.
Remove the bulb holder and
change the bulb.
Refit the bulb holder, the tab then
the rubber.
If you encounter any difficulties, con-
tact a PEUGEOT dealer.
Rear lights
1. Brake/side lights (P 21/5 W)
2. Direction indicators (P 21 W)
3. Reversing light (P 21 W),
left-hand side
These 3 bulbs are changed by re-
moving the light:
open the boot,
unscrew the two light fixing
nuts A,
remove the light unit by pulling
Fog lamp (P 21 W),
right-hand side
outwards,
71
PRACTICAL INFORMATION
9
Number plate lights (W 5 W)
Pass your hand under the bumper.
Remove the bulb holder turning it
one quarter of a turn.
Remove the bulb and change it.
Third brake light
(Four W 5 W bulbs)
Unscrew the 2 fixing bolts A.
Release the lamp unit by pushing
the two tabs B inwards.
Disconnect the connector and the
rear wash-wipe pipe.
Remove the bulb holder.
Remove the bulb and change it.
When refitting, proceed in the reverse
order and ensure that the lamp unit
seal and the rear wash-wipe pipe have
been put back in place correctly.
unclip the harness,
remove the bulb holder moving
aside the four tabs B,
remove the bulb and change it.
Do not tighten the bolts more
than is necessary at the risk
of breaking the light.
Note: when refitting, proceed in the
reverse order and take care to posi-
tion the bulb holder, the tabs and the
light correctly.
72
