Deutsch
EnglishMOBILITY for your BMW i3 2013-2022
Charging the vehicle
MOBILITY
Charging the vehicle
▷ AC charging station.
▷ DC charging station.
Vehicle features and options
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
For optimal use of the energy from the power
mains, charging at an AC charging station, for in‐
stance BMW i Wallbox, is recommended.
Charge current
General information
The charge current strength is indicated in am‐
peres.
The vehicle cannot automatically detect the max‐
imum permissible charge current strength of the
power grid during charging via a household
socket.
Concept
The vehicle can be charged using various charg‐
ing cables at charging stations or household
sockets. Control and monitoring of the charging
process are handled completely automatically.
The charge current strength can be set via
iDrive.
Charging on a household socket
Prior to the first charging at your own household
socket, as well as when charging at external elec‐
trical power sockets, the allowed charge current
strength must be determined, for instance by a
qualified electrician.
General information
The charge current strength for charging at a
household socket, refer to page 215, can be ad‐
justed in the vehicle in three levels.
High-voltage battery
The high-voltage battery is used as an energy
accumulator. The high-voltage battery can be
charged utilizing energy recovery during the trip
or via the power grid.
At delivery, the charge current for charging at a
household socket is set to the lowest level.
Depending on the country-specific version, one
of several ampere ratings is printed on the
In order to operate the high-voltage battery opti‐
mally, charge the vehicle regularly and fully using
a compatible charger.
Mode 2 charging cable. This ampere rating is the
limit which must be adhered to for the vehicle if
the charge current is set to the highest level. De‐
pending on the charging cable, the charge cur‐
rent strength may vary when lower levels are set.
When charging via the power grid, you can chose
between the following variants:
▷ Household socket.
208
Charging the vehicle
MOBILITY
Overview
Imprint on the charging cable
Charge current setting
"Max."
6 A
"Reduced"
6 A
"Low"
6 A
6 A
8 A
8 A
6 A
6 A
10 A
12 A
15 A
10 A
12 A
15 A
7.5 A
9 A
6 A
6 A
11.25 A
7.5 A
Depending on the charge current, the charging
duration changes.
Safety information
Charging at an AC quick charging station
Warning
The permitted charge current strength must be
determined prior to charging at an AC quick
charging station, for instance from the call opera‐
tor of the AC quick charging station. The permit‐
ted charge current strength can vary by country.
Improper working with electrical current can
lead to an electric shock due to high voltages or
high currents. There is a risk of fire or danger to
life. Observe the general safety regulations
when working with electrical current.
The charge current strength for charging at an
AC quick charging station, refer to page 215,
can be adjusted in the vehicle in two steps.
Warning
At delivery, the charge current for charging at an
AC quick charging station is set to "Reduced".
Maintain this setting unless it was verified that a
higher charge current strength is permitted in the
individual case.
A faulty and incorrectly designed charging de‐
vice at the charging location can cause damage
to the vehicle and overload the power mains at
the charging location. There is a risk of fire and
a risk of injury.
The charge current changes depending on the
setting.
The manufacturer of your vehicle recommends
that, prior to your first use of a charging loca‐
tion, you have the compatibility of the following
components confirmed:
"Max."
32 A
"Reduced"
16 A
▷ Charging cable.
▷ Charging station.
Range Extender
With Range Extender switched on, the current
charge state can be maintained. In this way, a
higher range is achieved.
▷ Household socket and connected circuits.
209
Charging the vehicle
MOBILITY
Safety information
Warning
Damaged or worn charging devices, for in‐
stance worn contacts, can heat up. There is a
risk of fire. Only use charging devices that are
in good condition.
Warning
Non-compatible charging cables or unsuitable
charging stations can heat up and cause dam‐
age to the vehicle. There is a risk of fire. Use
charging cables or charging stations for charg‐
ing that are suitable for the respective vehicle
type.
Warning
Simultaneous charging and refueling poses a
risk of fire if a sufficient safety distance from
easily flammable materials is not maintained.
There is a risk of injury or risk of damage to
property. Do not fill the vehicle with fuel and
charge it simultaneously.
A dealer's service center will be glad to provide
information about suitable charging cables.
Warning
Improper use of the charging cable can prevent
charging and lead to damage, for instance ca‐
ble fire. There is a risk of fire. Use the charging
cable only for charging the vehicle, and do not
extend it using cables or adapters.
Warning
Contact with live components can lead to an
electric shock. High voltage is present at the
charging connection. There is a risk of injury or
danger to life.
Warning
Have work on the charging connection, for in‐
stance cleaning, performed by an authorized
BMW i dealer's service center or another quali‐
fied service center or repair shop.
Damaged charging cables can heat up or lead
to an electric shock. There is a risk of fire or a
risk of injury. Use undamaged charging cables
only.
Mode 2 charging cable
Depending on the country version, the vehicle is
supplied with a Mode 2 charging cable.
Charging cable
General information
Use a Mode 2 charging cable, Mode 3 charging
cable, or the permanently installed cable of a
charging station to charge the vehicle.
Mode 2 charging cables can be used to charge
the vehicle from grounded household sockets.
Charging at household socket connections is
performed with alternating current.
Different charging cables can be required de‐
pending on the country.
When a Mode 2 charging cable is used, the effi‐
ciency values may differ from those stated on the
energy label.
The Mode 2 charging cable is also referred to as
standard charging cable.
210
Charging the vehicle
MOBILITY
If required, store the charging cable with the in‐
stalled connector cover to prevent moisture in
the charging cable plug.
Mode 3 charging cable
Depending on the country version, the vehicle is
supplied with a Mode 3 charging cable.
The Mode 3 charging cable makes it possible to
quickly recharge at sockets of designated AC
charging stations using a special connector.
Charging is performed with alternating current at
designated AC charging stations. The charging
process can be completed faster than at house‐
hold sockets.
Connecting
Charging socket flap
The charging socket flap is located on the right
side of the vehicle.
Always keep charging socket clean and unob‐
structed.
The charging cable may be permanently installed
at the charging station.
Keep the charging socket flap closed when the
charging socket is not used.
If a Mode 3 charging cable is used, apply the cor‐
responding setting via iDrive, refer to page 215.
Connecting the charging cable
The Mode 3 charging cable is also referred to as
AC quick charging cable.
To connect, engage selector lever position P,
deactivate drive-ready state, and unlock the vehi‐
cle. Set the parking brake, if needed.
DC charging cable
The DC charging cable that is permanently in‐
stalled at the charging station makes is possible
to charge at DC charging stations. Charging is
performed with direct current at designated DC
charging stations. At the higher dimensioned
power connection of a DC charging station, the
charging time is normally substantially reduced
compared to a household socket or AC charging
station.
1. Tap on the charging socket flap, arrow.
During charging at a DC charging station, an indi‐
cation in the instrument cluster, refer to
page 216, is displayed.
2. Remove the charging socket lid, arrow.
The vehicle must be charged with a 30 m DC
charging cable exclusively.
The DC charging cable is also referred to as
Mode 4 charging cable.
Storage
Depending on the national-market version, the
Mode 2 charging cable is located in the charging
cable compartment under the hood.
3. Remove the cover of the charging cable con‐
nector, if needed.
The Mode 3 charging cable can be stored in the
same place.
4. Connect the Mode 2 charging cable to the
household socket or the Mode 3 charging ca‐
Moisture can penetrate into the charging cable
compartment, for instance in a car wash.
211
Charging the vehicle
MOBILITY
ble to the port at the AC charging station as
7. Disconnect the Mode 2 charging cable from
needed.
the household socket or the Mode 3 charging
cable from the port at the AC charging station
as needed.
5. Insert the appropriate charging cable connec‐
tor, and push it in until it engages.
8. Stow the charging cable.
When charging at a charging station, follow the
instructions at the charging station.
At a charging station, insert the permanently
installed charging cable in the place provided
for it.
Removing
AC charging: when the charging process is ac‐
tive and the vehicle is locked, the charging cable
is locked. Unlock the vehicle before removing the
cable.
Unlocking the charging cable
Concept
In the following situations, the Mode 2 charging
cable or Mode 3 charging cable can be unlocked
and removed electronically:
Direct current charging: during the charging
process, the charging cable is locked. When the
charging process is completed, the charging ca‐
ble is automatically unlocked.
▷ When the vehicle is locked.
If necessary, clean the area between the charg‐
ing socket flap and charging socket, for instance
from snow, before removing it.
▷ When a charging station is defective.
Unlocking
Via iDrive:
1. Unlock the vehicle with the vehicle key if it is
locked.
1. "My Vehicle"
Charging cable is unlocked.
2. "Plan charging/climate control"
3. "Settings charging current"
4. "Unlock charging cable"
2. Press the release button on the handle, ar‐
row 1, and grasp the charging cable at the
gripping areas.
Charging process is interrupted.
Manual release
General information
The charging socket flap is automatically locked
while driving.
The charging cable may be locked during the
charging process if the vehicle is locked.
Manually unlocking the charging
socket flap
3. Remove the charging cable from the charg‐
ing socket, arrow 2.
In case of an electrical malfunction of the charg‐
ing cable lock, the charging socket flap can be
manually unlocked.
4. Put the charging socket lid back on.
5. Press on the charging socket flap until it en‐
gages.
6. Attach cover of the charging cable connector,
if needed.
212
Charging the vehicle
MOBILITY
5. For removing the charging cable, refer to
page 212.
1. Open the front door on the side of the charg‐
ing socket flap.
6. If necessary, press the knob back into the ini‐
tial position.
2. Open rear door on the side of the charging
socket flap.
Have the locking system of the charging socket
checked at the dealer’s service center or another
qualified service center or repair shop after emer‐
gency unlocking of the charging cable.
3. Remove the cover.
4.
Pull the top knob. This releases the charg‐
ing socket flap.
Charging process
General information
At high temperatures, the high-voltage battery is
initially cooled. There may be a delay before
charging starts. If the high-voltage battery is dis‐
charged, cooling of the high-voltage battery may
not be possible. The charging process cannot be
started.
5. If necessary, press the knob back into the ini‐
tial position.
If the Mode 2 charging cable is exposed to high
temperatures and direct sunlight, this may inter‐
rupt the charging process. Charging will resume
automatically.
Performing emergency release
In case of an electrical malfunction, the charging
cable can be manually unlocked.
When charging at a charging station, complete
the charging process at the charging station be‐
fore unlocking the charging cable.
The charging process may take longer under ex‐
tremely low or high temperatures.
Safety information
1. Open the front door on the side of the charg‐
ing socket flap.
2. Open rear door on the side of the charging
socket flap.
Warning
Improper use of the power mains connection
can lead to damage, for instance cable fire.
There is a risk of injury or risk of damage to
property. Use the charging cable only for charg‐
ing the vehicle, and do not extend it using ca‐
bles or adapters.
3. Remove the cover.
4.
Pull the lower knob.
The charging cable is manually unlocked.
Warning
If the charge current strength is adjusted incor‐
rectly, the power mains of the household
socket can be overloaded and overheat. There
is a risk of fire. Adjust the charge current
strength to the power mains prior to charging
213
Charging the vehicle
MOBILITY
on household sockets. With unknown power
networks, set on the lowest level.
Charging status display
Indicator light on the charging socket
Warning
An incorrectly connected charging cable can
lead to damage, for instance cable fire. There is
a risk of injury or risk of damage to property.
Make sure that the charging cable connector is
completely inserted in the charging socket.
NOTICE
An indicator light is located on the charging
socket.
Any weight on the opened charging port cover
may damage it. There is a risk of damage to
property, among other potential damage. Do
not put weight onto the charging port cover, for
instance by setting down the charging cable.
Charging status
Light
Charging status
White
Charging cable can be con‐
nected or removed.
Starting the charging process
1. Engage selector lever position P. Set the
parking brake, if needed.
Flashes yel‐ Charging process is being pre‐
low
pared.
2. For planning the charging process, refer to
page 215.
For DC charging: DC charging is
finishing.
3. Switch off drive-ready state.
Blue
Charging process paused.
Charging process is active.
4. Connect the Mode 2 charging cable to the
household socket or the Mode 3 charging ca‐
ble to the port at the AC charging station as
needed.
Flashes
blue
Flashes red Fault in the charging process.
Green Charging process is completed.
5. Open the charging socket flap.
6. Connect the charging cable to the vehicle, re‐
fer to page 211.
When the vehicle is locked, the indicator light
goes out after some time.
7. Lock vehicle if it is unlocked.
When the vehicle is unlocked, the blue indicator
light flashes continuously. The other indicator
lights go out after some time.
Press the button on the vehicle key to check
the charging state. The charging status is indi‐
cated on the indicator light. In some cases the
vehicle is locked.
214
Charging the vehicle
1. "My Vehicle"
MOBILITY
Additional messages about the charging status
can be displayed in the instrument cluster, on the
BMW display key, or via the BMW app on the
smartphone.
2. "Plan charging/climate control"
3. "Set low cost time slot"
4. Set rate begin.
Planning the charging process
General information
The charging process can be adapted to con‐
straints, for instance the cost of electricity. The
vehicle can control the charging process in such
a way that the charging process is completed at
the departure time. A departure time must be set
for this purpose, refer to page 217.
5. Set rate end.
The Digital Charging Service enables the time
window to be set automatically for current loca‐
tions. Further information about the Digital
Charging Service is available on the Internet:
The vehicle can also start the charging process
before the selected time window begins or end it
after the selected time window finishes. The
starting point of the charging process is adjusted
so the vehicle can be as fully charged as possible
and, if applicable, its climate adjusted by the de‐
parture time.
The following settings are available:
▷ Immediate charging.
▷ Set time window for favorable charging.
▷ Set charging via Mode 2 charging cable.
▷ Set charging via Mode 3 charging cable.
If drive-ready state is switched off, changes can
be made via iDrive.
If drive-ready state is switched off, changes can
be made via iDrive. The departure time change is
a one-off change. Scheduled departure times are
not adjusted. Settings for the stationary climate
control and charging process are also accepted
for planned departure times.
Set the charge current for charging via a
Mode 2 charging cable
Depending on the electrical mains, the vehicle
must be charged with a different charge current
strength, refer to page 208.
Via iDrive:
Setting the charging mode
Via iDrive:
1. "My Vehicle"
2. "Plan charging/climate control"
3. "Settings charging current"
4. "Level 1 (120V)"
1. "My Vehicle"
2. "Plan charging/climate control"
3. Select the desired setting:
Settings are stored. When you change charging
locations you also might need to change the set‐
ting for charging.
▷ "Charge immediately": the charging proc‐
ess starts as soon as the charging cable is
connected.
Set the charge current strength at third-party
household sockets to the lowest level.
▷ "Charge for departure time": if a departure
time is set, a time window for charging
with a favorable electricity rate can be set.
Set the charge current for charging via a
Mode 3 charging cable
Depending on the electrical mains, the vehicle
must be charged with a different charge current
strength, refer to page 209.
Setting the time window for favorable-
rate
Via iDrive:
215
Charging the vehicle
MOBILITY
When charging with an Mode 3 charging cable,
the charging process can be completed faster at
an AC charging station.
Terminating the charging process
1. Disconnect the charging cable from the vehi‐
cle, refer to page 212.
Via iDrive:
2. Stow the charging cable as required.
1. "My Vehicle"
3. Press on the charging socket flap until it en‐
gages.
2. "Plan charging/climate control"
3. "Settings charging current"
4. "Level 2 (208-240V)"
4. Lock vehicle if it is unlocked.
Settings are stored. When you change charging
locations you also might need to change the set‐
ting for charging.
Displays in the instrument
cluster
The charge state indicator light shows the
charge state of the high-voltage battery in the in‐
strument cluster, if standby state is switched on.
If all bars are filled, the high-voltage battery is
fully charged.
Automatically unlocking the charging
cable after the charging process
To allow other charging station customers to use
the charging function, the charging cable can be
unlocked automatically after the charging proc‐
ess is complete.
Even if no bars are filled, the high-voltage system
is still under high voltage.
Via iDrive:
Information regarding the charging process is
shown on the charging screen.
1. "My Vehicle"
2. "Plan charging/climate control"
3. "Settings charging current"
4. "Unlock charging cable"
Display Meaning
Blue connector: charging process ac‐
tive or completed.
White connector: charging process in‐
terrupted.
Stopping the charging process
The charging process can be stopped at any
time by removing the charging cable and contin‐
ued at a later time by connecting the charging
cable. This enables other consumers to use the
power connection or prevents simultaneous high
power from multiple consumers, for example.
Running light: animated with active
charging process.
End of charging time or set departure
time.
For removing the charging cable, refer to
page 212.
Charging progress bar.
Running light: animated with active
charging process.
Continuing the charging process
DC charging active on a DC charging
station.
If the charging process is interrupted, for in‐
stance through a temporary power failure, the
charging process is automatically continued after
the interruption.
Indicator in blue: charged electrical
range.
216
Charging the vehicle
MOBILITY
▷ Planning a one-time departure time.
Display Meaning
Indicator in white: maximum electrical
▷ Planning of up to three regular departure
times per day of the week.
range.
If drive-ready state is switched off, changes can
be made via iDrive. The departure time change is
a one-off change. Scheduled departure times are
not adjusted. Settings for climate control and
charging process are also applied for scheduled
departure times.
Charging cable connected.
White clock: departure time set.
White connector: charging procedure
is starting or interrupted.
Blue connector: charging process ac‐
tive or completed.
Climate control for departure time
Via iDrive:
Climate control activated at departure
time.
1. "My Vehicle"
2. "Plan charging/climate control"
3. "Precondition for departure"
Range with Range Extender.
Flashing: ventilation active.
Flashing: heating active.
Flashing: cooling active.
Setting the departure time
AC charging:
Via iDrive:
1. "My Vehicle"
2. "Plan charging/climate control"
3. "Set departure time"
4. Set the desired days of the week, if needed.
5. Set the desired time.
Up to three departure times can be set.
Departure time
Activating the departure time
Via iDrive:
Concept
For optimum range and climate control, the de‐
parture time can be set before parking the vehi‐
cle.
1. "My Vehicle"
2. "Plan charging/climate control"
3. "Set departure time"
General information
Set departure times are displayed.
4. For example activate "Departure time 1".
Up to three departure times can be activated.
With a set departure time, the vehicle is pre‐
heated or precooled during the charging process
if climate control is set. Climate control output is
reduced during the trip. This increases the range.
The set departure time will be deactivated, if the
departure time was ignored three times in a row.
The following settings are possible for departure
time:
▷ Climate control for departure time.
217
Charging the vehicle
MOBILITY
Climate control
General information
The following settings for vehicle air conditioning
are possible:
▷ Activate stationary climate control immedi‐
ately, refer to page 176.
The range is reduced if stationary climate
control is activated without a charging cable
connected.
▷ Planned climate control at the set departure
time, refer to page 177.
If a Mode 2 charging cable is used, the high-
voltage battery may not be fully charged at
departure time.
Discharged high-voltage and
vehicle battery
General information
In addition to the high-voltage battery, the vehi‐
cle has a 12 volt vehicle battery, which is re‐
quired for operation of the onboard electronics.
If the high-voltage battery and the vehicle battery
are discharged, it is not possible to operate the
vehicle.
Have the vehicle checked and returned to opera‐
tion by a dealer’s service center or another quali‐
fied service center or repair shop.
218
Refueling
MOBILITY
Refueling
Vehicle features and options
Tank vent
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
Concept
The vehicle is equipped with a special fuel tank.
The fuel tank is designed for special require‐
ments that arise from operation with the Range
Extender.
General information
Excess pressure may build up in the fuel tank as
a result of gasoline vapors; this pressure is dissi‐
pated before the fuel cap is opened.
General information
Overview
The button is located on the driver's floor area.
Follow the fuel recommendation, refer to
page 222, prior to refueling.
A sufficient amount of fuel must be added to op‐
erate the Range Extender. When the Range Ex‐
tender is activated, the current charge state is
maintained. The vehicle has a greater range.
Venting the tank
1. Switch off drive-ready state.
Do not refuel unless the engine is at a standstill
and the selector lever is in position P/N, other‐
wise the buildup of pressure may cause the fuel
nozzle to shut off prematurely.
2.
Press the button to start the pressure
equalization.
The tank venting status is displayed in the in‐
strument cluster. In rare cases, tank venting
can last several minutes.
When tank venting has finished, a message is
displayed in the instrument cluster. The fuel
filler flap is released for opening.
Safety information
3. Open the fuel filler flap.
NOTICE
If it is not possible to open the fuel filler flap
after tank venting, press the button again.
With a driving distance of less than
30 miles/50 km the engine may no longer have
sufficient fuel. Engine functions are not en‐
sured anymore. There is a risk of damage to
property, among other potential damage. Re‐
fuel promptly.
If it is still not possible to open the fuel filler
flap even after pressing the button again, un‐
lock the fuel filler flap manually, refer to
page 220.
219
Refueling
MOBILITY
Closing
Fuel cap
Warning
Opening
The retaining strap of the fuel cap can be jam‐
med and crushed during closing. The cap can‐
not be correctly closed. Fuel or fuel vapors can
escape. There is a risk of injury or risk of dam‐
age to property. Pay attention that the retaining
strap is not jammed or crushed when closing
the cap.
Before opening, vent the tank.
1. Briefly press the rear edge of the fuel filler
flap.
1. Fit the cap and turn it clockwise until you
clearly hear a click.
2. Press on the fuel filler flap until it engages.
Emergency unlocking
It may be necessary in certain situations to un‐
lock the fuel filler flap manually, for instance with
an electrical fault.
2. Turn the fuel cap counterclockwise.
The release is located under the hood.
1. Opening the hood, refer to page 240.
2. Pull the green button with the fuel pump icon.
This releases the fuel filler flap.
3. Place the fuel cap in the bracket attached to
the fuel filler flap.
3. Open the fuel filler flap.
220
Refueling
MOBILITY
4. Carefully open the fuel cap. Excess pressure
can build up in the fuel tank from gasoline va‐
por.
Safety information
Warning
Simultaneous charging and refueling poses a
risk of fire if a sufficient safety distance from
easily flammable materials is not maintained.
There is a risk of injury or risk of damage to
property. Do not fill the vehicle with fuel and
charge it simultaneously.
NOTICE
5. Refuel the vehicle as usual. The excess pres‐
sure in the tank may make refueling difficult,
for instance the fuel pump nozzle may shut
off frequently.
Fuels are toxic and aggressive. Overfilling of the
fuel tank can damage the fuel system. Painted
surfaces may be damaged by contact with fuel.
Escaping fuel can harm the environment. There
is a risk of damage to property, among other
potential damage. Avoid overfilling.
Have the vehicle checked immediately by a deal‐
er's service center or another qualified service
center or repair shop.
Follow the following when
refueling
General information
When refueling, insert the filler nozzle completely
into the filler pipe. Lifting up the fuel pump nozzle
during refueling causes:
▷ Premature switching off.
▷ Reduced return of the fuel vapors.
The fuel tank is full when the filler nozzle clicks
off the first time.
Make sure that the fuel cap is closed properly af‐
ter refueling, otherwise the emissions warning
light may light up.
Follow safety regulations posted at the gas sta‐
tion.
221
Fuel
MOBILITY
Fuel
Safety information
Vehicle features and options
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
NOTICE
Even small quantities of the wrong fuel or
wrong fuel additives can damage the fuel sys‐
tem and engine. Furthermore, the catalytic
converter is permanently damaged. There is a
risk of damage to property, among other poten‐
tial damage. Do not refuel or add the following
in the case of gasoline engines:
▷ Leaded gasoline.
▷ Metallic additives, for instance manganese
or iron.
Fuel recommendation
Do not press the Start/Stop button after refuel‐
ing with the wrong fuel. Contact a dealer’s serv‐
ice center or another qualified service center or
repair shop.
General information
Depending on the region, many gas stations sell
fuel that has been customized to winter or
summer conditions. Fuel that is available in win‐
ter, for instance helps make a cold start easier.
NOTICE
Fuel that does not comply with the minimum
quality can compromise engine function or
cause engine damage. There is a risk of dam‐
age to property, among other potential dam‐
age. Do not fill with fuel that does not comply
with the minimum quality.
Gasoline
General information
For the best fuel efficiency, the gasoline should
be sulfur-free or very low in sulfur content.
Fuels that are marked on the gas pump as con‐
taining metal must not be used.
Recommended fuel grade
BMW recommends AKI 91.
Fuels with a maximum ethanol content of 10 %,
i.e., E10, may be used for refueling.
Ethanol should meet the following quality stan‐
dards:
Refuel with this gasoline to achieve the rated
performance and consumption values.
US: ASTM 4806–xx
Minimum fuel grade
CAN: CGSB-3.511–xx
BMW recommends AKI 89.
xx: comply with the current standard in each
case.
222
Wheels and tires
MOBILITY
Wheels and tires
Tire inflation pressure specifications
In the tire inflation pressure table
Vehicle features and options
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
The tire inflation pressure table, refer to
page 224, contains all tire inflation pressure
specifications for the specified tire sizes at the
ambient temperature. The tire inflation pressure
values apply to tire sizes approved by the manu‐
facturer of the vehicle for the vehicle type.
To identify the correct tire inflation pressure,
please note the following:
▷ Tire sizes of your vehicle.
Tire inflation pressure
Checking the tire inflation pressure
General information
Tires heat up while driving. The tire inflation
pressure increases with the tire temperature.
General information
The tire inflation pressure and tire characteristics
influence the following:
▷ The service life of the tires.
▷ Road safety.
Tires have a natural, consistent loss of tire infla‐
tion pressure.
▷ Driving comfort.
The displays of inflation devices may under-read
by up to 0.1 bar/2 psi.
▷ Driving dynamics.
▷ Fuel consumption.
Checking using tire inflation pressure
specifications in the tire inflation pressure
table
Safety information
The tire inflation pressure specifications in the
tire inflation pressure table only relate to cold
tires or tires at the same temperature as the am‐
bient temperature.
Warning
A tire with too little or no tire inflation pressure
may heat up significantly and sustain damage.
This will have a negative impact on aspects of
handling, such as steering and braking re‐
sponse. There is a risk of accident. Regularly
check the tire inflation pressure, and correct it
as needed, for instance twice a month and be‐
fore a long trip.
Only check the tire inflation pressure levels when
the tires are cold, i.e.:
▷ Driving distance of max. 1.25 miles/2 km has
not been exceeded.
▷ If the vehicle has not moved again for at least
2 hours after a trip.
223
Wheels and tires
MOBILITY
Tire pressure values
1. Determine the intended tire inflation pressure
levels for the mounted tires.
i3 without Range Extender
2. Check the tire inflation pressure in all four
tires, using a pressure gage, for example.
Tire size
Pressure specifications in
3. Correct the tire inflation pressure if the actual
tire inflation pressure deviates from the in‐
tended tire inflation pressure.
bar/PSI
Specifications in
bar/PSI with cold
tires
4. Check whether all valve caps are screwed
onto the tire valves.
After correcting the tire inflation pressure
For run-flat tires: reinitialize run-flat tires.
155/70 R 19 84
Q A/S
2.7 / 39
3.0 / 44
For the Tire Pressure Monitor TPM: reset the
Tire Pressure Monitor TPM.
155/70 R 19 84
Q
155/70 R 19 88
Q XL M+S
Tire fill pressures
To achieve optimum driving comfort, note the
tire inflation pressure specifications in the Tire in‐
flation pressure table, refer to page 224, and ad‐
just as needed.
Front: 155/70 R
19 84 Q A/S
2.7 / 39
-
Rear: 175/60 R
19 86 Q A/S
-
3.0 / 44
Front: 155/70 R
19 84 Q
2.7 / 39
-
Rear: 175/60 R
19 86 Q
-
3.0 / 44
Front: 155/60 R
20 80 Q
2.7 / 39
-
Rear: 175/55 R
20 89 Q XL
-
3.0 / 44
-
These tire inflation pressure values can also be
found on the tire inflation pressure label on the
driver's side on the rear door.
Front: 175/55 R
20 89 T XL
2.7 / 39
-
Do not exceed a speed of 100 mph/160 km/h.
Rear: 195/50 R
20 93 T XL
3.0 / 44
224
Wheels and tires
Tire size
MOBILITY
i3 with Range Extender
Pressure specifications in
bar/PSI
Tire size
Pressure specifications in
bar/PSI
Front: 175/55
R 20 89 T XL
2.7 / 39
-
Specifications in
bar/PSI with cold
tires
Rear: 195/50 R
20 93 T XL
-
3.0 / 44
155/70 R 19 88 2.7 / 39
Q XL M+S
3.0 / 44
Tire identification marks
Front: 155/70 R 2.7 / 39
19 84 Q A/S
-
Tire size
245/45 R 18 96 Y
Rear: 175/60 R
19 86 Q A/S
-
3.0 / 44
245: nominal width in mm
45: aspect ratio in %
Front: 155/70 R 2.7 / 39
19 84 Q
-
R: radial tire code
18: rim diameter in inches
96: load rating, not for ZR tires
Y: speed rating, before the R on ZR tires
Rear: 175/60 R
19 86 Q
-
3.0 / 44
Front: 155/60 R 2.7 / 39
20 80 Q
-
Maximum tire load
Maximum tire load is the maximum permissible
weight for which the tire is approved.
Rear: 175/55 R
20 89 Q XL
-
3.0 / 44
-
Locate the maximum tire load on the tire sidewall
and the Gross Axle Weight Rating – GAWR – on
the certification label on the driver’s side on the
rear door.
Front: 175/55 R 2.7 / 39
20 89 T XL
Rear: 195/50 R
20 93 T XL
-
3.0 / 44
Divide the tire load by 1.1. It must be greater
than one-half of the vehicle’s Gross Axle Weight
Rating – GAWR. Note, front vs. rear GAWR and
tire loads, respectively.
i3s
Tire size
Pressure specifications in
bar/PSI
Speed letter
Specifications
in bar/PSI with
cold tires
Designation
Maximum speed
Q
R
S
T
up to 100 mph/160 km/h
up to 106 mph/170 km/h
up to 112 mph/180 km/h
up to 118 mph/190 km/h
155/70 R 19
88 Q XL M+S
2.7 / 39
3.0 / 44
225
Wheels and tires
MOBILITY
All passenger vehicle tires must conform to Fed‐
eral Safety Requirements in addition to these
grades.
Designation
Maximum speed
H
V
up to 131 mph/210 km/h
up to 150 mph/240 km/h
up to 167 mph/270 km/h
up to 186 mph/300 km/h
Treadwear
W
Y
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov‐
ernment test course. E.g., a tire graded 150
would wear one and one-half, 1 g, times as well
on the government course as a tire graded 100.
The relative performance of tires depends upon
the actual conditions of their use, however, and
may depart significantly from the norm due to
variations in driving habits, service practices and
differences in road characteristics and climate.
Tire Identification Number
DOT-Code: DOT xxxx xxx 0121
xxxx: manufacturer code for the tire brand
xxx: tire size and tire design
0121: tire age
Tires with DOT codes meet the guidelines of the
U.S. Department of Transportation.
Traction
Tire age
The traction grades, from highest to lowest, are
AA, A, B, and C.
Recommendation
Regardless of the tire tread, replace tires at least
every 6 years.
Those grades represent the tire's ability to stop
on wet pavement as measured under controlled
conditions on specified government test surfa‐
ces of asphalt and concrete. A tire marked C may
have poor traction performance.
Manufacture date
You can find the manufacture date of the tire on
the tire's sidewall.
The traction grade assigned to this tire is based
on straight-ahead braking traction tests, and
does not include acceleration, cornering, hydro‐
planing, or peak traction characteristics.
Designation
Manufacture date
1st week 2021
DOT … 0121
Temperature
Uniform Tire Quality Grading
Quality grades can be found where applicable on
the tire sidewall between tread shoulder and
maximum section width.
The temperature grades are A, the highest, B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate heat
when tested under controlled conditions on a
specified indoor laboratory test wheel. Sustained
high temperature can cause the material of the
tire to degenerate and reduce tire life, and exces‐
sive temperature can lead to sudden tire failure.
The grade C corresponds to a level of perform‐
ance which all passenger car tires must meet un‐
der the Federal Motor Vehicle Safety Standard
No. 109. Grades Band A represent higher levels
E.g.: Treadwear 200; Traction AA; Temperature
A
DOT Quality Grades
Treadwear
Traction AA A B C
Temperature A B C
226
Wheels and tires
MOBILITY
of performance on the laboratory test wheel than
the minimum required by law.
The positions of the wear indicators are marked
on the tire sidewall with TWI, Tread Wear Indica‐
tor.
Warning
The temperature grade for this tire is estab‐
lished for a tire that is properly inflated and not
overloaded. Excessive speed, underinflation, or
excessive loading, either separately or in com‐
bination, can cause heat buildup and possible
tire failure.
Tire damage
General information
Inspect your tires regularly for damage, foreign
objects lodged in the tread, and tread wear.
Driving over rough or damaged road surfaces, as
well as debris, curbs and other obstacles can
cause serious damage to wheels, tires and sus‐
pension parts. This is more likely to occur with
low-profile tires, which provide less cushioning
between the wheel and the road. Be careful to
avoid road hazards and reduce your speed, es‐
pecially if your vehicle is equipped with low-pro‐
file tires.
M+S
Winter and all-season tires with better cold
weather performance than summer tires.
Tire tread
Indications of tire damage or other vehicle mal‐
functions:
Summer tires
Do not drive with a tire tread of less than
0.12 in/3 mm, otherwise there is an increased
risk of hydroplaning.
▷ Unusual vibrations.
▷ Unusual tire or running noises.
▷ Unusual handling such as a strong tendency
to pull to the left or right.
Winter tires
Do not drive with a tire tread of less than
0.16 in/4 mm, as such tires are less suitable for
winter operation.
Damage can be caused by the following situa‐
tions, for instance:
▷ Driving over curbs.
▷ Road damage.
Minimum tread depth
▷ Tire inflation pressure too low.
▷ Vehicle overloading.
▷ Incorrect tire storage.
Safety information
Warning
Damaged tires can lose tire inflation pressure,
which can lead to loss of vehicle control. There
is a risk of accident. If tire damage is suspected
while driving, immediately reduce speed and
stop. Have wheels and tires checked. For this
purpose, drive carefully to the nearest dealer’s
Wear indicators are distributed around the tire's
circumference and have the legally required min‐
imum height of 0.063 inches/1.6 mm.
227
Wheels and tires
MOBILITY
service center or another qualified service cen‐
ter or repair shop. Have vehicle towed or trans‐
ported as needed. Do not repair damaged tires,
but have them replaced.
mended by the vehicle manufacturer for your
vehicle type.
Warning
Incorrect wheel/tire combinations will have a
negative impact on the vehicle's handling and
on the function of a variety of systems, such as
the ABS Antilock Braking System or DSC Dy‐
namic Stability Control. There is a risk of acci‐
dent. To maintain good handling and vehicle
response, use only tires with a single tread con‐
figuration from a single manufacturer. The
manufacturer of the vehicle recommends that
you use wheels and tires that have been rec‐
ommended by the vehicle manufacturer for
your vehicle type. Following tire damage, have
the original wheel/tire combination remounted
on the vehicle as soon as possible.
Warning
Tires can become damaged by driving over ob‐
stacles, e.g., curbs or road damage, at high
speed. Larger wheels have a smaller tire cross-
section. The smaller the tire cross-section, the
higher the risk of tire damage. There is a dan‐
ger of accidents and property damage. If possi‐
ble, avoid driving over objects or road condi‐
tions that may damage tires, or drive over them
slowly and carefully.
Changing wheels and tires
Recommended tire brands
Mounting
Have mounting and wheel balancing carried out
by a dealer’s service center or another qualified
service center or repair shop.
Wheel and tire combination
General information
You can ask the dealer's service center or an‐
other qualified service center or repair shop
about the correct wheel/tire combination and
wheel rim versions for the vehicle.
For each tire size, the manufacturer of the vehi‐
cle recommends certain tire brands. The tire
brands can be identified by a star on the tire
sidewall.
Safety information
New tires
Warning
Tire traction is not optimal due to manufacturing
circumstances when tires are brand-new; they
achieve their full traction potential after a break-in
time.
Wheels and tires which are not suitable for your
vehicle can damage parts of the vehicle, for in‐
stance due to contact with the body due to tol‐
erances despite the same official size rating.
There is a risk of an accident. The manufac‐
turer of your vehicle strongly suggests that you
use wheels and tires that have been recom‐
Drive conservatively for the first
200 miles/300 km.
228
Wheels and tires
MOBILITY
conditions. The tires can be rotated in pairs be‐
tween the axles to achieve even wear. Further in‐
formation is available from a dealer's service cen‐
ter or another qualified service center or repair
shop. After rotating, check the tire pressure and
correct, if needed.
Retreaded tires
Warning
Retreaded tires can have different tire casing
structures. With advanced age the service life
can be limited. There is a risk of an accident.
The manufacturer of your vehicle does not rec‐
ommend the use of retreaded tires.
Storing tires
Tire inflation pressure
Do not exceed the maximum tire inflation pres‐
sure indicated on the side wall of the tire.
The manufacturer of the vehicle does not rec‐
ommend the use of retreaded tires.
Winter tires
Winter tires are recommended for operating on
winter roads.
Storage
▷ Store wheels and tires in a cool, dry and dark
place.
Although so-called all-season M+S tires provide
better winter traction than summer tires, they
usually do not provide the same level of perform‐
ance as winter tires.
▷ Always protect tires against all contact with
oil, grease, and solvents.
▷ Do not leave tires in plastic bags.
▷ Remove dirt from wheels or tires.
Maximum speed of winter tires
If the maximum speed of the vehicle is higher
than the permissible speed for the winter tires,
then attach a label showing the permissible maxi‐
mum speed in the field of view. The label is avail‐
able from a dealer's service center or another
qualified service center or repair shop.
Repairing a flat tire
Safety measures
▷ Park the vehicle as far away as possible from
passing traffic and on solid ground.
With winter tires mounted, observe and do not
exceed the permissible maximum speed.
▷ Switch on the hazard warning system.
▷ Secure the vehicle against rolling away by
setting the parking brake.
Rotating wheels between axles
▷ Turn the steering wheel until the front wheels
are in the straight-ahead position and engage
the steering wheel lock.
Warning
Rotating tires between the axles on vehicles
with different tire sizes or rim sizes on the front
and rear axles can cause damage to the tires
and the vehicle. There is a risk of accident. Do
not rotate the tires between the axles on vehi‐
cles with different tire sizes or rim sizes on the
front and rear axles.
▷ Have all vehicle occupants get out of the ve‐
hicle and ensure that they remain outside the
immediate area in a safe place, such as be‐
hind a guardrail.
▷ If necessary, set up a warning triangle at an
appropriate distance.
Different wear patterns can occur on the front
and rear axles depending on individual driving
229
Wheels and tires
MOBILITY
Sealant container
Mobility System
Concept
With the Mobility System, minor tire damage can
be sealed temporarily to enable continued travel.
To accomplish this, sealant is pumped into the
tires, which seals the damage from the inside.
General information
▷ Follow the instructions on using the Mobility
System found on the compressor and sealant
container.
▷ Sealant container, arrow 1.
▷ Filling hose, arrow 2.
Observe use-by date on the sealant container.
▷ Use of the Mobility System may be ineffec‐
tive if the tire puncture measures approx.
1/8 inches/4 mm or more.
Compressor
▷ Contact a dealer's service center or another
qualified service center or repair shop if the
tire cannot be made drivable.
▷ Do not remove foreign bodies that have pe‐
netrated the tire. Only remove foreign objects
if they are visibly protruding from the tire.
▷ Pull the speed limit sticker off the sealant
container and apply it to the steering wheel.
▷ The use of a sealant can damage the TPM
wheel electronics. In this case, have the TPM
wheel electronics replaced at the next oppor‐
tunity.
1
2
3
4
5
6
7
8
Sealant container unlocking
Sealant container holder
Tire pressure gage
▷ The compressor can be used to check the
tire inflation pressure.
Reduce tire inflation pressure button
On/off switch
Compressor
Overview
Storage
Connector/cable for socket
Connection hose
The Mobility System is located in the storage
compartment under the hood.
230
Wheels and tires
MOBILITY
2. Pull filling hose completely out of the cover of
the sealant container. Do not kink the hose.
Filling the tire with sealant
Safety information
DANGER
If the exhaust pipe is blocked or ventilation is in‐
sufficient, harmful exhaust gases can enter into
the vehicle. The exhaust gases contain pollu‐
tants which are colorless and odorless. In en‐
closed areas, exhaust gases can also accumu‐
late outside of the vehicle. There is danger to
life. Keep the exhaust pipe free and ensure suf‐
ficient ventilation.
3. Slide the sealant container into the holder on
the compressor housing, ensuring that it en‐
gages audibly.
NOTICE
The compressor can overheat during extended
operation. There is a risk of damage to prop‐
erty, among other potential damage. Do not run
the compressor for more than 10 minutes.
Filling
1. Shake the sealant container.
4. Screw the filling hose of the sealant container
onto the tire valve of the nonworking wheel.
231
Wheels and tires
MOBILITY
5. With the compressor switched off, insert the
connector into the power socket in the vehi‐
cle interior.
Removing and stowing the sealant
container
1. Unscrew the filling hose of the sealant con‐
tainer from the tire valve.
2. Press the red unlocking device.
3. Remove the sealant container from the com‐
pressor.
4. Wrap and store the sealant container in suita‐
ble material to avoid dirtying the cargo area.
Minimum tire inflation pressure is not
reached
1. Pull the connector out of the power socket in
the vehicle interior.
6. With standby state or drive-ready state
switched on, switch on the compressor.
2. Drive 33 ft/10 m forward and back to distrib‐
ute the sealant in the tire.
3. Screw the connection hose of the compres‐
sor directly onto the tire valve stem.
Let the compressor run for max. 10 minutes to fill
the tire with sealant and achieve a tire inflation
pressure of approx. 2.0 bar.
While the tire is being filled with sealant, the tire
inflation pressure may sporadically reach approx.
5 bar. Do not switch off the compressor at this
point.
4. Insert the connector into the power socket in
the vehicle interior.
Checking and adjusting the tire
inflation pressure
Checking
1. Switch off the compressor.
2. Read the tire inflation pressure on the tire
pressure gage.
To continue the trip, a tire inflation pressure of at
least 2 bar must be reached.
5. With standby state or drive-ready state
switched on, switch on the compressor.
232
Wheels and tires
MOBILITY
If a tire inflation pressure of at least 2 bar can‐
not be reached, contact your dealer's service
center or another qualified service center or
repair shop.
3. Insert the connector into the power socket in
the vehicle interior.
If a tire inflation pressure of at least 2 bar is
reached, see Minimum tire inflation pressure
is reached.
6. Unscrew the connection hose of the com‐
pressor from the tire valve.
7. Pull the connector out of the power socket in
the vehicle interior.
4. Correct the tire inflation pressure to at least
2.0 bar.
8. Stow the Mobility System in the vehicle.
▷ Increase tire inflation pressure: with
standby state or drive-ready state
Minimum tire inflation pressure is
reached
1. Unscrew the connection hose of the com‐
pressor from the tire valve.
switched on, switch on the compressor.
▷ To reduce the pressure: press the button
on the compressor.
2. Pull the connector out of the power socket in
the vehicle interior.
5. Unscrew the connection hose of the com‐
pressor from the tire valve.
3. Stow the Mobility System in the vehicle.
6. Pull the connector out of the power socket in
the vehicle interior.
4. Immediately drive approx. 5 miles/10 km to
ensure that the sealant is evenly distributed in
the tire.
7. Stow the Mobility System in the vehicle.
Do not exceed a speed of 50 mph/80 km/h.
Continuing the trip
Do not exceed the maximum permissible speed
of 50 mph/80 km/h.
If possible, do not drive at speeds less than
12 mph/20 km/h.
Reinitialize the Flat Tire Monitor.
Adjustment
Reset the Tire Pressure Monitor TPM.
1. Stop at a suitable location.
Replace the nonworking tire and the sealant con‐
tainer of the Mobility System at the next opportu‐
nity.
2. Screw the connection hose of the compres‐
sor directly onto the tire valve stem.
233
Wheels and tires
MOBILITY
Do not reset the Tire Pressure Monitor TPM af‐
ter mounting tire chains, as doing so may result
in incorrect readings.
i3 without Sport Package: tire
chains
When driving with tire chains, briefly activate Dy‐
namic Traction Control DTC, if needed.
Safety information
Maximum speed with tire chains
Warning
Do not exceed a speed of 30 mph/50 km/h when
using tire chains.
With the mounting of tire chains on unsuitable
tires, the tire chains can come into contact with
vehicle parts. There may be a risk of accident
or risk of damage to property. Only mount tire
chains on tires that are designated by their
manufacturer as suitable for the use of tire
chains.
i3s and vehicles with Sport
Package: tire chains
General information
The manufacturer of the vehicle has determined
certain wheels and tires to be suitable for opera‐
tion on the vehicle. Mounting of tire chains on
these wheels and tires is not permitted.
Warning
Insufficiently tight tire chains may damage tires
and vehicle components. There may be a risk
of accident or risk of damage to property. Make
sure that the tire chains are always sufficiently
tight. Re-tighten as needed according to the
tire chain manufacturer's instructions.
Safety information
Warning
With the mounting of tire chains on unsuitable
tires, the tire chains can come into contact with
vehicle parts. There may be a risk of accident
or risk of damage to property. Do not mount tire
chains.
Fine-link tire chains
The manufacturer of the vehicle recommends
the use of fine-link tire chains. Certain types of
fine-link tire chains have been tested by the
manufacturer of the vehicle and recommended
as road-safe and suitable.
Information regarding suitable tire chains is avail‐
able from a dealer’s service center or another
qualified service center or repair shop.
Changing wheels/tires
General information
When a flat tire kit is used, an immediate wheel
change when there is a loss of tire inflation pres‐
sure in the event of a flat tire is not always neces‐
sary.
Use
Use only in pairs on the rear wheels, equipped
with the tires of the following size:
▷ 155/70 R 19.
If needed, the tools for changing wheels are
available as accessories from a dealer’s service
center or another qualified service center or re‐
pair shop.
Follow the tire chain manufacturer's instructions.
Do not initialize the Flat Tire Monitor after
mounting tire chains, as doing so may result in
incorrect readings.
234
Wheels and tires
MOBILITY
Safety information
Warning
The vehicle jack is optimized for lifting the vehi‐
cle and for the jacking points on the vehicle
only. There is a risk of injury. Do not lift any
other vehicle or cargo using the vehicle jack.
DANGER
The vehicle jack is only provided for short-term
lifting of the vehicle for wheel changes. Even if
all safety measures are observed, there is a risk
of the raised vehicle falling, if the vehicle jack
tips over. There is a risk of injuries or danger to
life. When the vehicle is raised with the vehicle
jack, do not lie under the vehicle and do not
switch on the drive-ready state.
Warning
When the vehicle jack is not inserted into the
jacking point provided for this purpose, the ve‐
hicle may be damaged or the vehicle jack may
slip when it is being cranked up. There is a risk
of injury or risk of damage to property. When
cranking up the vehicle jack, ensure that it is in‐
serted in the jacking point next to the wheel
housing.
DANGER
Supports such as wooden blocks under the ve‐
hicle jack reduce the capacity of the vehicle
jack to bear weight. They have the potential to
exert too much strain on the vehicle jack, caus‐
ing it to tip over and the vehicle to fall. There is
a risk of injuries or danger to life. Do not place
supports under the vehicle jack.
Warning
A vehicle that is raised on a vehicle jack may fall
off of the jack if lateral forces are exerted on it.
There is a risk of injury and risk of damage to
property. While the vehicle is raised, do not ex‐
ert lateral forces on the vehicle or pull abruptly
on the vehicle. Have a stuck wheel removed by
a dealer’s service center or another qualified
service center or repair shop.
Warning
The jack, issued by the vehicle manufacturer, is
provided in order to perform a wheel change in
the event of a breakdown. The jack is not de‐
signed for frequent use; for example, changing
from summer to winter tires. Using the jack fre‐
quently may cause it to become jammed or
damaged. There is a risk of injury and risk of
damage to property. Only use the jack to attach
an emergency or spare wheel in the event of a
breakdown.
Securing the vehicle against rolling
General information
The vehicle manufacturer recommends to addi‐
tionally secure the vehicle against rolling away
when changing a wheel.
Warning
On soft, uneven or slippery ground, for example
snow, ice, tiles, etc., the vehicle jack can slip
away. There is a risk of injury. If possible,
change the wheel on a flat, solid, and slip-re‐
sistant surface.
235
Wheels and tires
MOBILITY
On a level surface
▷ Lug bolt, arrow 1.
▷ Adapter, arrow 2.
Place chocks or other suitable objects, for exam‐
ple rocks, in front of and behind the wheel that is
diagonally opposite to the wheel that you wish to
change.
Unscrewing
1. Attach the adapter to the lug bolt.
2. Unscrew the lug bolt.
On a slight downhill gradient
3. Remove the adapter after unscrewing the lug
bolt.
Screwing on
1. Attach the adapter to the lug bolt. If neces‐
sary, turn the adapter until it fits on the lug
bolt.
2. Screw on the lug bolt. The tightening torque
is 140 Nm.
3. Remove the adapter and stow it after screw‐
ing on the lug bolt.
If you need to change a wheel on a slight down‐
hill grade, place chocks and other suitable ob‐
jects, for instance rocks, under the wheels of
both the front and rear axles against the rolling
direction.
Preparing the vehicle
▷ Park the vehicle on solid and non-slip ground
at a safe distance from traffic.
▷ Switch on the hazard warning system.
▷ Set the parking brake.
Lug bolt lock
Concept
The wheel lug bolts have a special coding. The
lug bolts can only be released with the adapter
which matches the coding.
▷ Engage a gear or move the selector lever to
position P.
▷ As soon as permitted by the traffic flow, have
all vehicle occupants get out of the vehicle
and ensure that they remain outside the im‐
mediate area in a safe place, such as behind a
guardrail.
Overview
The adapter of the lug bolt lock is in the onboard
vehicle tool kit or in a storage compartment close
to the onboard vehicle tool kit.
236
Wheels and tires
MOBILITY
▷ Depending on the vehicle equipment, get
wheel change tools and, if necessary, the
emergency wheel from the vehicle.
1. Hold the vehicle jack with one hand, arrow 1,
and grasp the vehicle jack crank with your
other hand, arrow 2.
▷ If necessary, set up a warning triangle or port‐
able hazard warning light at an appropriate
distance.
▷ Secure the vehicle additionally against rolling.
▷ Loosen the lug bolts a half turn.
Jacking points for the vehicle jack
2. Insert the vehicle jack into the rectangular re‐
cess of the jacking point closest to the wheel
to be changed.
The jacking points for the vehicle jack are lo‐
cated at the indicated positions.
Jacking up the vehicle
3. Extend the vehicle jack by turning the vehicle
jack crank or lever clockwise.
Warning
Hands and fingers can be jammed when using
the vehicle jack. There is a risk of injury. Com‐
ply with the described hand position and do not
change this position while using the vehicle
jack.
4. Take your hand away from the vehicle jack as
soon as the vehicle jack is under load and
continue turning the vehicle jack crank or
lever with one hand.
237
Wheels and tires
MOBILITY
5. Make sure that the vehicle jack foot stands
vertically and at a right angle beneath the
jacking point.
5. Turn the vehicle jack crank counterclockwise
to retract the vehicle jack and lower the vehi‐
cle.
6. Remove the vehicle jack and stow it securely.
After the wheel change
1. Tighten the lug bolts crosswise. The tighten‐
ing torque is 101 lbs ft/140 Nm.
2. Stow the nonworking wheel in the cargo area,
if necessary.
The nonworking wheel cannot be stored un‐
der the cargo floor panel because of its size.
6. Make sure that the vehicle jack foot stands
vertically and perpendicularly beneath the
jacking point after extending the vehicle jack.
3. Check tire inflation pressure at the next op‐
portunity and correct as needed.
4. Reinitialize the Flat Tire Monitor.
Reset the Tire Pressure Monitor TPM.
5. Check to make sure the lug bolts are tight
with a calibrated torque wrench.
6. Have the damaged tire replaced at the near‐
est dealer's service center or another quali‐
fied service center or repair shop.
7. Crank the vehicle up, until the vehicle jack is
with the entire surface on the ground and the
relevant wheel is maximum 1.2 inches/3 cm
above ground.
Mounting a wheel
Mount one emergency wheel only, as required.
1. Unscrew the lug bolts.
2. Remove the wheel.
3. Put the new wheel or emergency wheel on
and screw in at least two lug bolts in a cross‐
wise pattern until hand-tight.
If non-original light-alloy wheels of the vehicle
manufacturer are mounted, the accompany‐
ing lug bolts may have to be used as well.
4. Hand-tighten the remaining lug bolts and
tighten all lug bolts well in a crosswise pat‐
tern.
238
Under the hood
MOBILITY
Under the hood
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
Vehicle features and options
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
Overview
1
2
Washer fluid reservoir
3
4
Climate control coolant reservoir
Drivetrain coolant reservoir
With Range Extender: filler flap emergency
unlocking
The charging cable compartment in the center is
used for storage of the charging cables.
Moisture can penetrate into the charging cable
compartment, for instance in a car wash.
239
Under the hood
MOBILITY
Opening hood
Hood
Unlocking the hood
Safety information
1.
Press the button on the vehicle key
or the button in the driver's floor area, refer to
page 72.
Warning
An incorrectly locked hood can open while driv‐
ing and restrict visibility. There is a risk of acci‐
dent. Stop immediately and correctly close the
hood.
Opening hood
1. Press the release handle and open the hood.
Warning
Body parts can be jammed when opening and
closing the hood. There is a risk of injury. Make
sure that the area of movement of hood is clear
during opening and closing.
Warning
Indicator/warning lights
When the hood is opened, a Check Control mes‐
sage is displayed.
Improperly executed work under the hood can
damage components and lead to a safety risk.
There is a risk of accidents or risk of damage to
property. The manufacturer of your vehicle rec‐
ommends that work under the hood be per‐
formed only by an authorized BMW i dealer's
service center or another qualified service cen‐
ter or repair shop.
Closing the hood
NOTICE
Folded-away wipers can be jammed when the
hood is opened. There is a risk of damage to
property, among other potential damage. Make
sure that the wipers with the wiper blades
mounted are folded down onto the windshield
before opening the hood.
From approx. 16 inches/40 cm height allow to fall
and press again to lock the hook completely.
Make sure you hear the hood engage.
240
Engine oil
MOBILITY
Engine oil
Vehicle features and options
Checking the oil level
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
General information
Check the engine oil level with Range Extender
warmed up to operating temperature.
After switching off the Range Extender, wait sev‐
eral minutes before checking the oil level so that
the engine oil can collect in the oil pan.
Checking
1. Park the vehicle in horizontal position in a
safe place.
General information
2. Switch the engine off.
3. Remove the cargo floor panel.
Engine oil consumption depends on the fre‐
quency of Range Extender use. Therefore, regu‐
larly check the engine oil level after refueling.
Safety information
NOTICE
An engine oil level that is too low causes en‐
gine damage. There is a risk of damage to
property, among other potential damage. Im‐
mediately add engine oil.
4. Turn the lid counterclockwise and remove.
NOTICE
Too much engine oil can damage the engine or
the catalytic converter. There is a risk of dam‐
age to property, among other potential dam‐
age. Do not add too much engine oil. When too
much engine oil is added, have the engine oil
level corrected by a dealer’s service center or
another qualified service center or repair shop.
241
Engine oil
MOBILITY
5. After approx. 5, minutes, remove the dip stick
and wipe with a lint-free cloth, paper towel or
similar.
6. Carefully insert the dipstick up to the stop in
the measuring tube, and pull it back out.
The engine oil level must be between the two
marks of the dipstick.
Adding or changing engine oil
Have engine oil added or changed by a dealer's
service center or another qualified service center
or repair shop if necessary.
242
Coolant
MOBILITY
Coolant
Vehicle features and options
Warning
Additives are harmful and incorrect additives
can damage the engine. There is a risk of injury
and risk of damage to property. Do not allow
additives to come into contact with skin, eyes
or articles of clothing. Use suitable additives
only.
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
Coolant reservoir
The vehicle has two coolant reservoirs that are
located under the hood.
General information
To ensure the operational reliability of the vehi‐
cle, always check the coolant level of both cool‐
ant reservoirs.
Coolant consists of water and additives.
The vehicle's cooling circuits are filled with differ‐
ent types of coolant. Do not mix the different
types of coolant.
Opening the hood, refer to page 240.
Not all commercially available additives are suita‐
ble for the vehicle. Do not mix additives of differ‐
ent colors. Observe the water - additive mixing
ratio of 50:50. Information about suitable addi‐
tives is available from a dealer’s service center or
another qualified service center or repair shop.
Safety information
1
2
Climate control coolant reservoir
Drivetrain coolant reservoir
Warning
With the engine hot and the cooling system
open, coolant can escape and lead to scalding.
There is a risk of injury. Only open the cooling
system with the engine cooled down.
Coolant level
Climate control coolant reservoir
Checking
1. Allow the air conditioner to cool down.
2. Opening the hood.
243
Coolant
MOBILITY
3. Remove the cover.
service center or repair shop as quickly as
possible.
4. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres‐
sure to dissipate.
Drivetrain coolant reservoir
Checking
1. Allow the drive to cool down.
2. Opening the hood.
3. Remove the cover.
4. Check the coolant level.
The marks are on the side of the coolant res‐
ervoir. The coolant level is correct if it lies be‐
tween the minimum and maximum marks.
5. Open the coolant reservoir lid.
6. Check the coolant level.
Adding coolant
1. Allow the air conditioner to cool down.
The coolant level is correct if it lies between
the minimum and maximum marks in the res‐
ervoir.
2. Opening the hood.
3. Remove the cover.
7. Close the lid.
4. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres‐
sure to dissipate.
Adding coolant
1. Allow the air conditioner to cool down.
2. Opening the hood.
3. Remove the cover.
4. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres‐
sure to dissipate.
5. Open the coolant reservoir lid.
6. Slowly add coolant up to the specified level;
do not overfill.
7. Close the lid.
8. Have cause of the coolant loss eliminated by
a dealer’s service center or another qualified
service center or repair shop as quickly as
possible.
5. Open the coolant reservoir lid.
6. Slowly add coolant up to the specified level;
do not overfill.
7. Close the lid.
8. Have cause of the coolant loss eliminated by
a dealer’s service center or another qualified
244
Coolant
MOBILITY
Disposal
Comply with the relevant environmental
protection regulations when disposing of
coolant and coolant additives.
245
Maintenance
MOBILITY
Maintenance
Vehicle features and options
Condition Based Service CBS
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
Concept
Sensors and special algorithms take into account
the driving conditions of the vehicle. CBS uses
these to provide maintenance recommendations.
The system makes it possible to adapt the
amount of maintenance corresponding to your
user profile.
General information
Information on service notifications, refer to
page 119, can be displayed on the Control Dis‐
play.
BMW maintenance system
The maintenance system provides service notifi‐
cations and thereby provides support in main‐
taining road safety and the operational reliability
of the vehicle.
Service data in the vehicle key
Information on the service notifications is contin‐
uously stored in the vehicle key. The service
center can read this data out and suggest a
maintenance scope for the vehicle.
In some cases, scopes and intervals of the main‐
tenance system may vary according to the coun‐
try version. Replacement work, spare parts, fuels
and lubricants, and wear materials are calculated
separately. Further information is available from a
dealer's service center or another qualified serv‐
ice center or repair shop.
Therefore, hand the service advisor the vehicle
key with which the vehicle was driven most re‐
cently.
Storage periods
Storage periods during which the vehicle battery
was disconnected are not taken into account.
Safety information
If this occurs, have a dealer's service center or
another qualified service center or repair shop
update the time-dependent maintenance proce‐
dures, such as checking brake fluid and, if neces‐
sary, changing the engine oil and the microfilter/
activated-charcoal filter.
DANGER
Improperly performed work, in particular main‐
tenance and repair on the high-voltage system,
can lead to electric shock. There is a risk of in‐
jury, fire and danger to life.
Have work on the vehicle, in particular mainte‐
nance and repair, performed by an authorized
BMW i dealer’s service center or another quali‐
fied service center or repair shop.
246
Maintenance
MOBILITY
the foregoing, the manufacture of your vehicle
strongly recommends that access to the socket
for Onboard Diagnosis be limited to a dealer's
service center or another qualified service cen‐
ter or repair shop or other persons that have
the specialized training and equipment for pur‐
poses of properly utilizing the socket for On‐
board Diagnosis.
Maintenance Manual and
Service and Warranty
Information Booklet for US
models and Warranty and
Service Guide Booklet for
Canadian models
Please consult your Maintenance Manual and
Service and Warranty Information Booklet for US
models and Warranty and Service Guide Booklet
for Canadian models for additional information on
the performance of service and maintenance
work.
Position
The manufacturer of your vehicle recommends
that maintenance and repair be performed by a
service center or another qualified service center
or repair shop. Records of regular maintenance
and repair work should be retained.
Located on the driver's side is an OBD socket for
reading the vehicle data.
Socket for OBD Onboard
Diagnosis
On vehicles with Range Extender, additional
components are checked that are critical for its
emissions mix.
General information
Emissions
Applies to vehicles with Range Extender.
Devices connected to the OBD socket trigger
the alarm system when the vehicle is locked. Re‐
move any devices connected at the OBD socket
before locking the vehicle.
▷ The warning light lights up:
Emissions are deteriorating. Have the
vehicle checked as soon as possible.
Safety information
▷ The warning light flashes under certain cir‐
cumstances:
NOTICE
This indicates that there is excessive misfiring
in the engine.
The socket for Onboard Diagnosis is an intri‐
cate component intended to be used in con‐
junction with specialized equipment to check
the vehicle’s primary emissions system. Im‐
proper use of the socket for Onboard Diagno‐
sis, or contact with the socket for Onboard Di‐
agnosis for other than its intended purpose,
can cause vehicle malfunctions and creates
risks of personal and property damage. Given
Reduce the vehicle speed and have the sys‐
tem checked immediately; otherwise, serious
engine misfiring within a brief period can seri‐
ously damage emission control components,
in particular the catalytic converter.
247
Replacing components
MOBILITY
Replacing components
3. Position the wiper blade in a horizontal posi‐
tion.
Vehicle features and options
4. Remove the wiper blade toward one side.
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
5. Insert the new wiper blade in reverse order of
removal until it locks in place.
Wiper blades
Safety information
NOTICE
6. Fold down the wipers.
Replacing the rear wiper blade
1. Fold up the wiper arm.
The window may sustain damage if the wiper
falls onto it without the wiper blade installed.
There is a risk of damage to property, among
other potential damage. Hold the wiper firmly
when changing the wiper blade. Do not fold or
switch on the wiper without a wiper blade in‐
stalled.
2. Turn the wiper blade all the way back.
Replacing the front wiper blades
1. To change the wiper blades, fold up the wiper
arms, refer to page 108.
3. Continue turning the wiper blade all the way
so that it pops out of the holder.
2. Fold up the wipers.
4. Press the new wiper blade into the holder un‐
til you hear it snap into place.
5. Fold the wipers in.
248
Replacing components
MOBILITY
droplets in the light, have the headlights
checked.
Light/bulb replacement
General information
Vehicle battery
Lights and bulbs
The vehicle battery has 12 volts. The battery
supplies the onboard electronics with energy.
Lights and bulbs make an essential contribution
to vehicle safety.
For information about the high-voltage system,
refer to page 208.
All headlights and lights are made using LED
technology.
The vehicle manufacturer recommends that you
have the relevant work carried out a dealer’s
service center or another qualified service center
or repair shop.
Maintenance
The battery is maintenance-free.
More information about the battery can be re‐
quested from a dealer's service center or another
qualified service center or repair shop.
Follow the safety information, refer to page 249.
Light-emitting diodes (LEDs)
Replacing the vehicle battery
General information
The lights use light-emitting diodes installed be‐
hind the cover as a light source. These light-
emitting diodes are related to conventional lasers
and are officially designated as Class 1 light-
emitting diodes.
The manufacturer of your vehicle recommends
that you have a dealer's service center or another
qualified service center or repair shop register
the vehicle battery to the vehicle after the battery
has been replaced. Once the battery has been
registered again, all comfort features will be avail‐
able without restriction and any Check Control
messages displayed which relate to comfort fea‐
tures will disappear.
Safety information
Light-emitting diodes (LEDs)
Warning
Intensive brightness can irritate or damage the
retina of the eye. There is a risk of injury. Do not
look directly into the headlights or other light
sources. Do not remove the LED covers.
Safety information
Warning
Vehicle batteries that are not compatible can
damage vehicle systems and impair vehicle
functions. There is a risk of an accident and
damage to property. Only vehicle batteries that
are compatible with your vehicle type should be
installed in your vehicle. Information on com‐
patible vehicle batteries is available at your
dealer’s service center.
Headlight glass
Condensation can form on the inside of the
headlight glass in cool or humid weather. When
driving with the lights switched on, the conden‐
sation evaporates after a short time. The head‐
light glass does not need to be changed.
If despite driving with the headlights switched on,
increasing humidity forms, for instance water
249
Replacing components
MOBILITY
Charging the vehicle battery
General information
For charging a discharged battery, refer to
page 218.
Fuses
Safety information
Warning
Safety information
Incorrect and repaired fuses can overload elec‐
trical lines and components. There is a risk of
fire. Never attempt to repair a blown fuse. Do
not replace a nonworking fuse with a substitute
of another color or amperage rating.
NOTICE
Non-compatible external chargers can damage
the vehicle. There is a risk of an accident and
damage to property. Only loading devices that
are compatible with your vehicle and that are
below the maximum charge voltage should be
used to charge your vehicle. Information on
compatible chargers is available at your dealer’s
service center.
Accessing the fuses
The fuses are located in the passenger floor area
under the dashboard.
1. To open, loosen screws, arrows 1.
Power failure
After a power loss, some equipment needs to be
newly initialized or individual settings updated, for
example:
▷ Time: update.
▷ Date: update.
▷ Glass sunroof and sun protection: initialize
the system.
2. Fold down the fuse holder, arrow 2.
Proceed in the reverse order to install.
Disposing of old batteries
Information on the fuse types and locations, as
well as the positions of any other fuse boxes, is
available on the Internet: ‐
card.
Have old batteries disposed of by a deal‐
er’s service center or another qualified
service center or repair shop or take
them to a collection point.
Where applicable, information on the fuse types
and locations is also found on a separate sheet in
the fuse box.
Maintain the filled battery in an upright position
for transport and storage. Secure the battery so
that it does not tip over during transport.
Replacing fuses
The vehicle manufacturer recommends that you
have a dealer's service center or another quali‐
fied service center or repair shop replace the
fuses.
250
Breakdown assistance
MOBILITY
Breakdown assistance
Storage
Vehicle features and options
Storage for the first-aid kit is provided in the rear
in the cargo area.
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
BMW Roadside Assistance
Concept
Contact the BMW Group Roadside Assistance if
assistance is needed in the event of a break‐
down.
General information
In the event of a breakdown, data on the vehi‐
cle's condition is sent to the vehicle manufac‐
turer.
Hazard warning flashers
There are various ways of making contact.
▷ Via a Check Control message, refer to
page 117.
▷ Calling with a mobile phone.
▷ Via the BMW Connected app.
The button is located in the center console.
Requirements
The red light in the button flashes when the haz‐
ard warning flashers are activated.
▷ Active ConnectedDrive contract, equipment
with intelligent emergency call or BMW Con‐
nectedDrive services.
▷ Cellular network reception.
▷ Standby state is switched on.
Warning triangle
The warning triangle is located under the hood.
Starting
If the vehicle is equipped with Teleservices, sup‐
port is offered through Teleservice Diagnosis.
First-aid kit
Via iDrive:
General information
1. "ConnectedDrive"
Some of the articles have a limited service life.
2. "BMW Assist"
Check the expiration dates of the contents regu‐
larly and replace any expired items promptly.
3. "BMW i Roadside Assistance"
251
Breakdown assistance
MOBILITY
The contact to the Roadside Assistance of
the manufacture is established.
For technical reasons, the Emergency Call can‐
not be guaranteed under unfavorable conditions.
A telephone number is displayed, if needed.
Select to dial the telephone number on a
connected mobile phone.
Overview
Teleservice Diagnosis
Teleservice Diagnosis enables the wireless
transmission of detailed vehicle data that is im‐
portant for vehicle diagnosis. This data is trans‐
mitted automatically.
Teleservice Help
Depending on the country, the Teleservice Help
enables a more in-depth diagnosis of the vehicle
via wireless transmission.
SOS button in the roofliner.
Functional requirements
▷ The Assist system is functional.
▷ The ignition is switched on.
You can launch Teleservice Help by requesting it
through the Service Specialist.
1. Park the vehicle in a safe place.
2. Set the parking brake.
▷ If the vehicle is equipped with intelligent
emergency call: the SIM card integrated in
the vehicle has been activated.
3. Control Display is switched on.
4. Confirm Teleservice Help.
Automatic triggering
The driving ability of the vehicle can be restored
for specific functions.
Under certain conditions, for instance if the air‐
bags trigger, an emergency call is automatically
initiated immediately after an accident of corre‐
sponding severity. Automatic Collision Notifica‐
tion is not affected by pressing the SOS button.
If this is not possible, further measures will be ini‐
tiated, for instance Roadside Assistance will be
informed.
Manual triggering
1. Tap the cover.
Emergency Call
2. Press and hold the SOS button until the LED
on the button illuminates green.
Intelligent emergency call
▷ The LED is illuminated green when an emer‐
gency call has been initiated.
Concept
In case of an emergency, an emergency call can
be triggered automatically by the system or man‐
ually.
If a cancel prompt appears on the Control
Display, the emergency call can be aborted.
If the situation allows, wait in your vehicle until
the voice connection has been established.
General information
▷ The LED flashes green when a connection to
the BMW Response Center has been estab‐
lished.
Only press the SOS button in an emergency.
Intelligent emergency call establishes a connec‐
tion with the BMW Response Center.
252
Breakdown assistance
MOBILITY
The BMW Response Center then makes
contact with you and takes further steps to
help you.
▷ Immediately notify rescue forces, police, or
firefighters of the fact that your vehicle is
equipped with a high-voltage system.
Even if you are unable to respond, the BMW
Response Center can take further steps to
help you under certain circumstances.
▷ Engage selector lever position P, set the
parking brake, and switch off the standby
state and drive-ready state.
For this purpose, data that serves to deter‐
mine the necessary rescue measures, for in‐
stance the current position of the vehicle
when it can be determined, is transmitted to
the BMW Response Center.
▷ Lock the vehicle after exiting.
▷ Do not inhale any gases escaping from the
high-voltage battery; if needed, maintain a
safe distance from the vehicle.
Even if you can no longer hear the BMW Re‐
sponse Center through the loudspeakers, the
BMW Response Center may still be able to
hear you.
Jump-starting
General information
Have only a dealer’s service center or another
qualified service center or repair shop perform
the jump start.
The BMW Response Center ends the emer‐
gency call.
What to do after an accident
Safety information
Warning
Safety information
DANGER
Contact with live components can lead to an
electric shock. There is a risk of injuries or dan‐
ger to life. Do not touch any components that
are under voltage.
Contact with live components can lead to an
electric shock. There is a risk of injuries or dan‐
ger to life. After an accident, do not touch any
high-voltage components such as orange col‐
ored high-voltage cables or parts that are in
contact with exposed high-voltage cables.
Towing
Transporting the vehicle
Warning
General information
The vehicle is not permitted to be towed.
Fluids in the high-voltage battery are corrosive.
There is a risk of injury. Do not touch fluids es‐
caping from the high-voltage battery.
General information
After an accident, comply with the following
safety precautions with regard to the high-volt‐
age system:
▷ Secure the crash site.
253
Breakdown assistance
MOBILITY
Safety information
Towing other vehicles
General information
NOTICE
Switch on the hazard warning system, depend‐
ing on local regulations.
The vehicle can be damaged when towing the
vehicle with a single lifted axle. There is a risk of
damage to property, among other potential
damage. The vehicle should only be trans‐
ported on a loading platform.
If the electrical system has failed, clearly identify
the vehicle being towed by placing a sign or a
warning triangle in the rear window.
Safety information
Pushing the vehicle
To remove a broken-down vehicle from the dan‐
ger area, push it for a short distance at a speed
of no more than 6 mph/10 km/h.
Warning
If the approved gross vehicle weight of the tow‐
ing vehicle is lighter than the vehicle to be
towed, the tow fitting can tear off or it will not
be possible to control the vehicle's response.
There is a risk of accident. Make sure that the
gross vehicle weight of the towing vehicle is
heavier than the vehicle to be towed.
For rolling or pushing the vehicle, refer to
page 99.
Tow truck
NOTICE
If the tow bar or tow rope is attached incor‐
rectly, damage to other vehicle parts can occur.
There is a risk of damage to property, among
other potential damage. Correctly attach the
tow bar or tow rope to the tow fitting.
The vehicle should only be transported on a
loading platform.
Tow bar
The tow fittings used should be on the same
side on both vehicles.
NOTICE
The vehicle can become damaged when lifting
and securing it.
Should it prove impossible to avoid mounting the
tow bar at an offset angle, please follow the fol‐
lowing:
There is a risk of damage to property, among
other potential damage.
▷ Maneuvering capability is limited going
around corners.
▷ Lift the vehicle using suitable means.
▷ The tow bar will generate lateral forces if it is
secured with an offset.
▷ Do not lift or secure the vehicle by its tow
fitting, body parts, or suspension parts.
Tow rope
Observe the following notes when using the tow
rope:
254
Breakdown assistance
MOBILITY
▷ Use nylon ropes or straps, which will enable
Safety information
the vehicle to be towed without jerking.
▷ Make sure the tow rope is not twisted when
fastening.
NOTICE
If the tow fitting is not used as intended, there
may be damage to the vehicle or to the tow fit‐
ting. There is a risk of damage to property,
among other potential damage. Follow the
notes on using the tow fitting.
▷ Check the fastening of the tow fitting and tow
rope in regular intervals.
▷ Do not exceed a towing speed of
30 mph/50 km/h.
▷ Do not exceed a towing distance of
3 miles/5 km.
Screw thread for tow fitting
▷ When starting to tow the vehicle, make sure
that the tow rope is taut.
Tow fitting
General information
Press on the mark on the edge of the cover to
push it out.
The screw-in tow fitting should always be carried
in the vehicle.
The tow fitting can be screwed in at the front or
rear of the vehicle.
The tow fitting is located in the storage compart‐
ment under the hood.
Use of the tow fitting:
▷ Use only the tow fitting provided with the ve‐
hicle and screw it all the way in.
▷ Use the tow fitting for towing on paved roads
only.
▷ Avoid lateral loading of the tow fitting, for in‐
stance do not lift the vehicle by the tow fit‐
ting.
▷ Check the fastening of the tow fitting in regu‐
lar intervals.
255
Care
MOBILITY
Care
Vehicle features and options
NOTICE
When washing, water can get into the open
charging socket. There is a risk of damage to
property, among other potential damage. Close
the charging socket flap while washing.
This chapter describes all standard, country-spe‐
cific and optional features offered with the series.
It also describes features and functions that are
not necessarily available in your vehicle, e.g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be ob‐
served.
Steam blaster and high-pressure
washer
Safety information
Washing the vehicle
NOTICE
When cleaning with high-pressure washers,
components can be damaged due to the pres‐
sure or temperatures being too high. There is a
risk of damage to property, among other poten‐
tial damage. Maintain sufficient distance and do
not spray too long continuously. Follow the op‐
erating instructions for the high-pressure
washer.
General information
Regularly remove foreign objects such as leaves
in the area below the windshield when the hood
is raised.
Wash your vehicle frequently, particularly in win‐
ter. Intense soiling and road salt can damage the
vehicle.
Safety information
Distances and temperature
▷ Maximum temperature: 140 ℉/60 ℃.
Warning
▷ Minimum distance from sensors, cameras,
seals: 12 inches/30 cm.
Contact with live components can lead to an
electric shock. High voltage is present at the
charging connection. There is a risk of injury or
danger to life.
▷ Minimum distance from the charging socket
flap: 31.5 in/80 cm.
Have work on the charging connection, for in‐
stance cleaning, performed by an authorized
BMW i dealer's service center or another quali‐
fied service center or repair shop.
256
Care
MOBILITY
Driving into a car wash
Automatic washing systems or car
washes
Safety information
Safety information
NOTICE
Selector lever position P is automatically en‐
gaged when standby state is switched off.
There is a risk of damage to property, among
other potential damage. Do not switch standby
state off in car washes.
NOTICE
Using a car wash with high pressure washers
may result in water penetration of window
areas. There is a risk of damage to property,
among other potential damage. Do not drive
into high-pressure car wash systems.
General information
In a car wash, the vehicle must be able to roll
freely.
NOTICE
Improper use of automatic washing systems or
car washes can cause damage to the vehicle.
There is a risk of damage to property, among
other potential damage. Follow the following in‐
structions:
To roll or push the vehicle, refer to page 99.
Some car washes do not permit persons in the
vehicle. The vehicle cannot be locked from the
outside when in selector lever position N. A sig‐
nal sounds when an attempt is made to lock the
vehicle.
▷ Give preference to cloth car washes or
those that use soft brushes in order to
avoid paint damage.
Driving out of a car wash
Ensure that the vehicle key is in the car.
▷ Do not drive through a car wash with
guide rails higher than 4 in/10 cm to avoid
damage to the chassis.
Activate drive-ready state. For activating drive-
ready state, refer to page 97.
▷ Observe the tire width of the guide rail to
avoid damage to tires and rims.
Headlights
Do not rub wet headlights dry and do not use
abrasive or acidic cleaning agents.
▷ Fold in exterior mirrors to avoid damage to
the exterior mirrors.
▷ Unscrew the rod antenna to avoid the rod
antenna breaking off.
Soak areas that have been dirtied, for instance
from insects, with shampoo and wash off with
water.
▷ Deactivate the wiper and, if necessary, rain
sensor to avoid damage to the wiper sys‐
tem.
Thaw ice with de-icing spray; do not use an ice
scraper.
After washing the vehicle
After washing the vehicle, apply the brakes
briefly to dry them; otherwise, braking action can
be reduced. The heat generated during braking
dries brake discs and brake pads and protects
them against corrosion.
257
Care
MOBILITY
Completely remove all residues on the windows,
to minimize loss of visibility due to smearing and
to reduce wiper noises and wiper blade wear.
Leather care
Remove dust from the leather regularly, using a
cloth or vacuum cleaner.
Otherwise, particles of dust and road grime chafe
in pores and folds, and lead to increased wear
and premature degradation of the leather sur‐
face.
Vehicle care
Vehicle care products
To guard against discoloration, such as from
clothing, clean leather and provide leather care
roughly every two months.
General information
The vehicle manufacturer recommends using
care and cleaning products for BMW i. Suitable
care products are available from a dealer’s serv‐
ice center or another qualified service center or
repair shop.
Clean light-colored leather more frequently be‐
cause soiling on such surfaces is substantially
more visible.
Use leather care products; otherwise, dirt and
grease will gradually break down the protective
layer of the leather surface.
Safety information
Upholstery material care
General information
Vacuum the upholstery regularly with a vacuum
cleaner.
Warning
Cleansers can contain substances that are dan‐
gerous and harmful to your health. There is a
risk of injury. When cleaning the interior, open
the doors or windows. Only use products in‐
tended for cleaning vehicles. Follow the in‐
structions on the container.
If upholstery is very dirty, for instance with bever‐
age stains, use a soft sponge or microfiber cloth
with a suitable cleaning agent.
Clean the upholstery down to the seams using
large sweeping motions. Avoid rubbing the ma‐
terial vigorously.
Vehicle paint
General information
Safety information
Regular care contributes to driving safety and
value retention. Environmental influences in
areas with elevated air pollution or natural con‐
taminants, such as tree resin or pollen can affect
the vehicle's paintwork. Tailor the frequency and
extent of your vehicle care to these influences.
NOTICE
Open Velcro® fasteners on articles of clothing
can damage the seat covers. There is a risk of
damage to property, among other potential
damage. Ensure that any Velcro® fasteners are
closed.
Corrosive substances such as spilled fuel, oil,
grease or bird droppings, must be removed im‐
mediately to prevent the finish from being altered
or discolored.
Matte finish
Only use cleaning and care products suitable for
vehicles with matte finish.
258
Care
MOBILITY
Plastic components
Caring for special components
Light-alloy wheels
NOTICE
When cleaning the vehicle, use only neutral
wheel cleaners having a pH value from 5 to 9. Do
not use abrasive cleaning agents or steam jets
above 140 ℉/60 ℃. Follow the manufacturer's
instructions.
Cleaning agents that contain alcohol or sol‐
vents, such as lacquer thinners, heavy-duty
grease removers, fuel and such, can damage
plastic parts. There is a risk of damage to prop‐
erty, among other potential damage. Clean with
a microfiber cloth. Dampen the cloth lightly with
water, if needed.
Aggressive, acidic or alkaline cleaning agents can
destroy the protective layer of adjacent compo‐
nents, such as the brake disc.
Clean with a microfiber cloth.
After cleaning, apply the brakes shortly to dry
them. The heat generated during braking dries
brake discs and brake pads and protects them
against corrosion.
Dampen the cloth lightly with water, if needed.
Do not soak the roofliner.
Safety belts
Chrome surfaces
Carefully clean components such as the radiator
grille or door handles with plenty of water, if nec‐
essary, with shampoo added, particularly when
they have been exposed to road salt.
Warning
Chemical cleansers can destroy the safety belt
webbing. Missing protective effect of the safety
belts. There is a risk of injuries or danger to life.
Use only a mild soapy solution for cleaning the
safety belts.
Rubber components
Environmental influences can cause surface soil‐
ing of rubber parts and a loss of gloss. Use only
water and suitable cleaning agents for cleaning.
Dirty belt straps impede the reeling action and
thus have a negative impact on safety.
Treat especially worn rubber parts with rubber
care agents at regular intervals. When cleaning
rubber seals, do not use any silicon-containing
vehicle care products in order to avoid damage
or noises.
Use only a mild soapy solution, with the safety
belts clipped into their buckles.
Safety belts should only be allowed to retract if
they are dry.
Carpets and floor mats
Fine wood parts
Clean fine wood facing and fine wood compo‐
nents only with a suitable care product.
Warning
Objects in the driver's floor area can limit the
pedal distance or block a depressed pedal.
There is a risk of accident. Stow objects in the
vehicle such that they are secured and cannot
enter into the driver's floor area. Use floor mats
that are suitable for the vehicle and can be
safely attached to the floor. Do not use loose
floor mats and do not layer several floor mats.
Kenaf
Only treat parts made of Kenaf fibers, for in‐
stance in the door trims, using suitable care
products.
259
Care
MOBILITY
Make sure that there is sufficient clearance for
the pedals. Ensure that the floor mats are se‐
curely fastened again after they were removed,
for instance for cleaning.
Do not park the vehicle for longer than 14 days if
the electric range is less than 6 mls/10 km.
With storage times of up to three months, if pos‐
sible plug the vehicle into a compatible power
source or park it with the high-voltage battery as
fully charged as possible.
Floor mats can be removed from the car's inte‐
rior for cleaning.
If the floor carpets are very dirty, clean with a mi‐
crofiber cloth and water or an upholstery cleaner.
To prevent matting of the carpet, rub back and
forth in the direction of travel only.
General information
Your dealer's service center or another qualified
service center or repair shop can advise you on
what to consider when storing the vehicle for
longer than three months.
Sensor/camera lenses
Follow the instructions for discharging the high-
voltage battery, refer to page 197.
To clean sensors and camera lenses, use a cloth
moistened with a small amount of glass deter‐
gent.
Safety information
Displays/screens
NOTICE
The high-voltage battery can be damaged if left
uncharged or with low charge for extended pe‐
riods. There is a risk of damage to property,
among other potential damage. Before storing
the vehicle for an extended period, ensure that
the high-voltage battery is fully charged. During
the idle period, connect the vehicle to a charg‐
ing station at a compatible charging location. If
necessary, the high-voltage battery will be
charged automatically. Make sure that charging
is carried out. Regularly check the charge state.
NOTICE
Chemical cleaning agents, moisture or fluids of
any kind can damage the surface of displays
and screens. There is a risk of damage to prop‐
erty, among other potential damage. Clean with
a clean, antistatic microfiber cloth.
NOTICE
The surface of displays can be damaged with
improper cleaning. There is a risk of damage to
property, among other potential damage. Avoid
pressure that is too high and do not use any
scratching materials.
Do not allow the vehicle to sit idle for longer
than four weeks with a charge state below ap‐
prox. 80 %.
Clean with a clean, antistatic microfiber cloth.
High-voltage battery, long stationary
periods
Concept
For idle phases that last several weeks, park the
vehicle with the high-voltage battery fully
charged, if possible.
260
Care
MOBILITY
261
