Deutsch
EnglishMOBILITY for your BMW 8 Series 2018-2025
Refueling
MOBILITY
Refueling
Safety information
Vehicle features and options
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
NOTICE
With a range below 30 miles/50 km, the
engine may no longer have sufficient fuel.
Engine functions are not ensured anymore.
There is a risk of damage to property. Refuel
promptly.
NOTICE
Fuels are toxic and aggressive. Overfilling of
the fuel tank can damage the fuel system.
Painted surfaces may be damaged by con-
tact with fuel. Escaping fuel can harm the
environment. There is a risk of damage to
property. Avoid overfilling.
Follow the following when
refueling
General information
Follow the fuel recommendation prior to refuel-
ing.
When refueling, hook the fuel pump nozzle
completely into the filler pipe. Lifting up the fuel
pump nozzle while refueling causes:
Fuel cap
Opening
▷
▷
Premature switching off.
1. To open the fuel filler flap, press on the rear
edge, arrow. The fuel filler flap opens.
Reduced return of the fuel vapors.
The fuel tank is full when the fuel pump nozzle
clicks off the first time.
Make sure that the fuel cap is closed properly
after refueling, otherwise the emissions warn-
ing light may illuminate.
Follow safety regulations posted at the filling
station.
Additional information:
Fuel quality, refer to page 343.
308
Online Edition for Part no. 01405B381F1 - II/24
Refueling
MOBILITY
2. Turn the fuel cap counterclockwise.
Have the fuel filler flap unlocked by an author-
ized service center or another qualified service
center or repair shop.
3. Place the fuel cap in the bracket attached to
the fuel filler flap.
Closing
Warning
The fuel filler cap's retaining strap can be-
come pinched and crushed when the cap is
closed. It will then not be possible to close
the fuel filler cap correctly. Fuel or fuel vapors
can escape. There is a risk of injury or risk
of damage to property. Make sure that the
retaining strap does not become pinched or
crushed when closing the fuel filler cap.
1. Fit the fuel cap and turn it clockwise until
you clearly hear a click.
2. Press on the fuel filler flap until it engages.
Emergency unlocking
It may be necessary in certain situations to un-
lock the fuel filler flap manually, for instance
with an electrical malfunction.
309
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Wheels and tires
Tire pressure specifications
Vehicle features and options
In the tire inflation pressure table
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
The tire inflation pressure table contains all tire
inflation pressure specifications for the speci-
fied tire sizes at the ambient temperature. The
tire inflation pressure values apply to tire sizes
recommended by the manufacturer of the ve-
hicle for the vehicle type.
To identify the correct tire inflation pressure,
please note the following:
▷
▷
Tire sizes of the vehicle.
Maximum speed for driving.
Tire pressure
On the control display
General information
The tire condition and tire pressure influence
the following:
The current tire inflation pressure values and
the intended tire inflation pressure values for
the mounted tires can be displayed on the con-
trol display.
▷
▷
▷
▷
The service life of the tires.
Driving safety.
To ensure that they are displayed correctly, the
tire sizes must be stored in the system and
must have been set for the mounted tires.
Driving comfort.
Fuel consumption.
The current tire inflation pressure value is lo-
cated on each tire.
Safety information
The reference tire inflation pressure value is
located in the lower area of the control display.
Warning
A tire with too little or no tire inflation pres-
sure may heat up significantly and sustain
damage. This will have a negative impact
on aspects of handling such as steering and
braking response. There is a risk of accident,
injury, or property damage. Regularly check
the tire inflation pressure, and correct it as
needed, for instance twice a month and be-
fore a long trip.
Checking the tire pressure
General information
Tires heat up while driving. The tire pressure
increases with the tire temperature.
Tires have a natural, consistent tire pressure
loss.
The displays of inflation devices may under-
read by up to 0.1 bar/2 psi.
310
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Reinitialize the Flat Tire Monitor.
With Tire Pressure Monitor:
Checking using tire inflation pressure
specifications in the tire inflation
pressure table
1. Determine the intended tire inflation pres-
sure levels for the mounted tires.
The corrected tire inflation pressures are ap-
plied automatically. Make sure that the correct
tire settings have been made.
2. Check the tire inflation pressure in all four
tires, using a pressure gage, for example.
With tires that cannot be found in the tire pres-
sure values on the control display, reset the
Tire Pressure Monitor (TPM).
3. Correct the tire inflation pressure if the ac-
tual tire inflation pressure deviates from the
intended tire inflation pressure.
Tire inflation pressures up to
100 mph/160 km/h
For speeds of up to 100 mph/160 km/h and
for optimum driving comfort, note the pressure
values in the tire inflation pressure table and
adjust as necessary.
4. Check whether all valve caps are screwed
onto the tire valves.
The tire inflation pressure specifications in the
tire inflation pressure table only relate to cold
tires or tires at the same temperature as the
ambient temperature.
Only check the tire inflation pressure levels
when the tires are cold, i.e.:
▷
A distance traveled of max. 1.25 miles/2 km
has not been exceeded.
▷
If the vehicle has not moved again for at
least 2 hours after a trip.
Checking using the tire inflation
pressure specifications on the control
display
These pressure values can also be found on
the tire pressure label on the driver's door pil-
lar.
1. "CAR"
Do not exceed a speed of 100 mph/160 km/h.
2. "Vehicle status"
3.
"Tire Pressure Monitor"
4. Check whether the current tire inflation
pressure levels deviate from the intended
tire pressure value.
5. Correct the tire inflation pressure if the ac-
tual tire inflation pressure deviates from the
intended tire inflation pressure.
The display of the current tire pressure may be
limited when the vehicle is stationary. After a
short drive, the tire pressure is updated.
After correcting the tire pressure
For the flat tire monitor:
311
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
840i xDrive
Tire pressure values up to
100 mph/160 km/h
Tire size
Pressure specifica-
tions in bar/PSI
840i
Specifications in
bar/PSI with cold
tires
Tire size
Pressure specifica-
tions in bar/PSI
Specifications in
bar/PSI with cold
tires
245/40 R 19 98 H
XL M+S
2.4 / 35
2.6 / 38
245/40 R 19 98 V
XL M+S
245/40 R 19 98 H
XL M+S
2.2 / 32
2.6 / 38
Front: 245/40 R 19 2.4 / 35
98 H XL A/S
-
245/40 R 19 98 V
XL M+S
Rear: 275/35 R 19
100 H XL A/S
-
2.4 / 35
Front: 245/40 R 19 2.2 / 32
98 H XL A/S
-
Front: 245/40 R 19 2.4 / 35
98 Y XL
-
Rear: 275/35 R 19
100 H XL A/S
-
2.4 / 35
Rear: 275/35 R 19
100 Y XL
-
2.4 / 35
-
Front: 245/40 R 19 2.2 / 32
98 Y XL
-
Front:
245/35 R 20 95
Y XL
2.5 / 36
Rear: 275/35 R 19
100 Y XL
-
2.4 / 35
-
Front:
245/35 R 20 95
Y XL
2.4 / 35
Rear: 275/30 R 20
97 Y XL
-
2.8 / 41
-
Front: 245/40 R 19 2.4 / 35
98 V XL M+S
Rear: 275/30 R 20
97 Y XL
-
2.8 / 41
-
Rear: 275/35 R 19
100 V XL M+S
-
2.4 / 35
Front: 245/40 R 19 2.2 / 32
98 V XL M+S
Rear: 275/35 R 19
100 V XL M+S
-
2.4 / 35
312
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
inflation pressure table, and adjust as neces-
sary.
M850i xDrive
Tire size
Pressure specifica-
tions in bar/PSI
Tire pressure values over
100 mph/160 km/h
Specifications in
bar/PSI with cold
tires
840i
Tire size
Pressure specifica-
tions in bar/PSI
245/40 R 19 98 H
XL M+S
2.5 / 36
2.7 / 39
245/40 R 19 98 V
XL M+S
Specifications in
bar/PSI with cold
tires
Front: 245/40 R 19 2.5 / 36
98 H XL A/S
-
245/40 R 19 98 H
XL M+S
2.5 / 36
2.7 / 39
3.0 / 44
Rear: 275/35 R 19
100 H XL A/S
-
2.5 / 36
-
245/40 R 19 98 V
XL M+S
3.2 / 46
Front:
245/35 R 20 95
Y XL
2.7 / 39
Front: 245/40 R 19 2.5 / 36
98 H XL A/S
-
Rear: 275/30 R 20
97 Y XL
-
2.8 / 41
-
Rear: 275/35 R 19
100 H XL A/S
-
2.8 / 41
Front: 245/40 R 19 2.5 / 36
98 V XL M+S
Front: 245/40 R 19 2.5 / 36
98 Y XL
-
Rear: 275/35 R 19
100 V XL M+S
-
2.5 / 36
Rear: 275/35 R 19
100 Y XL
-
2.8 / 41
-
Tire pressures, 100 mph/160 km/h
Front:
2.7 / 39
245/35 R 20 95
Y XL
Warning
When driving at speeds greater than
Rear: 275/30 R 20
97 Y XL
-
3.2 / 46
-
100 mph/160 km/h, incorrect tire pressures
can negatively affect vehicle handling, e.g.,
safety or comfort while driving. The tires can
become damaged, which may cause an ac-
cident. There is a risk of accident, injury,
or property damage. To drive at maximum
speeds, note the specified tire pressure for
driving above 100 mph/160 km/h in the tire
Front: 245/40 R 19 2.7 / 39
98 V XL M+S
Rear: 275/35 R 19
100 V XL M+S
-
3.0 / 44
313
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
840i xDrive
M850i xDrive
Tire size
Pressure specifica-
tions in bar/PSI
Tire size
Pressure specifica-
tions in bar/PSI
Specifications in
bar/PSI with cold
tires
Specifications in
bar/PSI with cold
tires
245/40 R 19 98 H
XL M+S
2.6 / 38
2.8 / 41
3.0 / 44
245/40 R 19 98 H
XL M+S
2.7 / 39
3.0 / 44
3.0 / 44
245/40 R 19 98 V
XL M+S
3.2 / 46
245/40 R 19 98 V
XL M+S
3.3 / 48
Front: 245/40 R 19 2.6 / 38
98 H XL A/S
-
Front: 245/40 R 19 2.7 / 39
98 H XL A/S
-
Rear: 275/35 R 19
100 H XL A/S
-
2.8 / 41
Rear: 275/35 R 19
100 H XL A/S
-
2.8 / 41
-
Front: 245/40 R 19 2.6 / 38
98 Y XL
-
Front:
245/35 R 20 95
Y XL
3.1 / 45
Rear: 275/35 R 19
100 Y XL
-
2.8 / 41
-
Rear: 275/30 R 20
97 Y XL
-
3.2 / 46
-
Front:
245/35 R 20 95
Y XL
2.9 / 42
Front: 245/40 R 19 3.0 / 44
98 V XL M+S
Rear: 275/30 R 20
97 Y XL
-
3.2 / 46
-
Rear: 275/35 R 19
100 V XL M+S
-
3.1 / 45
Front: 245/40 R 19 2.8 / 41
98 V XL M+S
Tire marking
Rear: 275/35 R 19
100 V XL M+S
-
3.0 / 44
Tire size
245/45 R 18 96 Y
245: nominal width in mm
45: cross-sectional relationship in %
R: radial tire code
18: rim diameter in inches
96: load index
Y: speed code letter
314
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
ZR tires: reinforced radial tire for speeds ex-
ceeding 150 mph/240 km/h
Tire age
Recommendation
Regardless of the tire tread depth, replace tires
at least every 6 years.
Maximum tire load
Maximum tire load is the maximum permissi-
ble weight for which the tire is approved.
Manufacture date
You can find the manufacture date of the tire
on the tire sidewall.
Locate the maximum tire load on the tire
sidewall and the Gross Axle Weight Rating –
GAWR – on the certification label on the driver
door B-pillar. Divide the tire load by 1.1. It must
be greater than one-half of the vehicle’s Gross
Axle Weight Rating – GAWR. Note, front vs.
rear GAWR and tire loads, respectively.
Designation
Manufacture date
DOT … 0124
1st week of 2024
Uniform Tire Quality Grading
Quality grades can be found where applicable
on the tire sidewall between tread shoulder
and maximum section width.
Speed letter
Designation Maximum speed
Q
R
up to 100 mph/160 km/h
up to 106 mph/170 km/h
up to 112 mph/180 km/h
up to 118 mph/190 km/h
up to 131 mph/210 km/h
up to 150 mph/240 km/h
up to 167 mph/270 km/h
up to 186 mph/300 km/h
above 186 mph/300 km/h
E.g.: Treadwear 200; Traction AA; Tempera-
ture A
S
DOT Quality Grades
Treadwear
T
Traction AA A B C
Temperature A B C
H
V
All passenger vehicle tires must conform to
Federal Safety Requirements in addition to
these grades.
W
Y
(Y)
Treadwear
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov-
ernment test course. E.g., a tire graded 150
would wear one and one-half, 1 g, times as
well on the government course as a tire graded
100. The relative performance of tires depends
upon the actual conditions of their use, how-
ever, and may depart significantly from the
norm due to variations in driving habits, service
practices and differences in road characteris-
tics and climate.
Tire Identification Number
DOT code: DOT xxxx xxx 0124
xxxx: manufacturer code for the tire brand
xxx: tire size and tire design
0124: tire age
Tires with DOT codes meet the guidelines of
the U.S. Department of Transportation.
315
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Traction
M+S
The traction grades, from highest to lowest,
are AA, A, B, and C.
Winter tires, as well as all-season tires with
better winter performance than summer tires,
can be identified by the M+S marking on the
tire side wall.
Those grades represent the tire's ability to
stop on wet pavement as measured under
controlled conditions on specified government
test surfaces of asphalt and concrete. A tire
marked C may have poor traction perform-
ance.
Tire tread
Safety information
Warning
The traction grade assigned to this tire is
based on straight-ahead braking traction tests,
and does not include acceleration, cornering,
hydroplaning, or peak traction characteristics.
If the tire tread depth is too low, driving
safety may be impaired in critical situations
such as aquaplaning or slush on the road.
There is a risk of accident, injury, or property
damage. The tire tread depth may not fall
below 0.12 in/3 mm for summer tires and
0.16 in/4 mm for winter and all-season tires,
or observe the statutory regulations on mini-
mum tread depth.
Temperature
The temperature grades are A, the highest, B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the
material of the tire to degenerate and reduce
tire life, and excessive temperature can lead to
sudden tire failure. The grade C corresponds
to a level of performance which all passenger
car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades Band
A represent higher levels of performance on
the laboratory test wheel than the minimum
required by law.
Minimum tread depth
Warning
The temperature grade for this tire is estab-
lished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla-
tion, or excessive loading, either separately
or in combination, can cause heat buildup
and possible tire failure.
Distributed over the tire circumference are
the tire manufacturer’s wear indicators with a
height of at least 0.06 in/1.6 mm, which serve
as an indicator of tire tread wear.
The positions of the wear indicators are
marked on the tire sidewall with TWI, Tread
Wear Indicator.
Runflat tires
Runflat tires, refer to page 319, are labeled
with a circular icon containing the letters RSC
marked on the tire sidewall.
316
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Tire damage
Warning
The wheels, tires and chassis components
can become damaged when driving over
curbs, road damage, or other obstacles.
Larger wheels have a smaller tire cross-sec-
tion. The smaller the tire cross-section, the
higher the risk of tire damage. There is a
risk of accident, injury, or property damage. If
possible, avoid driving over curbs, road dam-
age or other obstacles, or drive over them
slowly and carefully.
General information
Check your tires regularly for damage, foreign
objects lodged in the tread, and tread wear.
Indications of tire damage or other vehicle mal-
functions:
▷
▷
▷
Unusual vibrations.
Unusual tire or running noises.
Unusual vehicle handling such as a strong
tendency to pull to the left or right.
▷
Uneven wear pattern, e.g., increased wear
in the area of the tire shoulder.
Exchanging wheels and
tires
Damage can be caused by the following situa-
tions, for instance:
▷
▷
▷
▷
▷
Driving over curbs.
Road damage.
Mounting and wheel balancing
Have the wheel mounted and balanced by an
authorized service center or another qualified
service center or repair shop.
Tire pressure too low.
Vehicle overloading.
Incorrect tire storage.
Suitable wheels and tires
Safety information
General information
Only certain wheel/tire combinations are suit-
able depending on vehicle and equipment.
The vehicle manufacturer determines wheel/
tire combinations on the basis of the following
criteria:
Warning
Damaged tires can lose tire inflation pres-
sure, which can lead to loss of vehicle control.
There is a risk of accident, injury, or property
damage. If tire damage is suspected while
driving, immediately reduce speed and stop.
Have wheels and tires checked. To do so,
drive carefully to an authorized service center
or another qualified service center or repair
shop. Have the vehicle towed or transported
as needed. Do not repair damaged tires, but
have them replaced.
▷
▷
Tire size, e.g., tire width, aspect ratio.
Wheel size, e.g., rim diameter, offset.
For more information on wheel/tire combina-
tions and special equipment, contact an au-
thorized service center or another qualified
service center or repair shop.
317
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Safety information
Recommended tire brands
Warning
Wheels and tires that are not suitable for
the vehicle can damage parts of the vehicle.
There is a risk of accident, injury, or prop-
erty damage. The vehicle manufacturer rec-
ommends that you use only wheels and tires
that have been recommended for the vehicle
type.
Tire types are developed for each vehicle and
optimized specifically for the individual require-
ments of that vehicle, e.g.:
Warning
▷
▷
▷
Vehicle handling.
Comfort.
Mounted steel wheels can cause technical
problems, for instance unexpected loosening
of the lug bolts and damage to the brake
disks. There is a risk of accident, injury,
or property damage. Do not mount steel
wheels.
Noise characteristics.
Specially developed tires are marked with
a star on the tire sidewall. After replacing
wheels and tires, the vehicle manufacturer rec-
ommends using star-marked tires again. The
vehicle manufacturer recommends that you
use tires of the same make and tread design.
Warning
Wheel/tire combinations that are not suitable
for the vehicle can affect vehicle handling
and a number of system functions, e.g.,the
Antilock Braking System or Dynamic Stability
Control. There is a risk of accident, injury, or
property damage. The manufacturer of the
vehicle recommends that you use wheels and
tires that have been recommended by the
vehicle manufacturer for the vehicle type. Fol-
lowing tire damage, have the original wheel/
tire combination remounted on the vehicle as
soon as possible.
New tires
Tire traction is not optimal due to manufactur-
ing circumstances when tires are brand new.
Drive conservatively for the first
200 miles/300 km.
Retreaded tires
Warning
Retreated tires can have different tire casing
structures. With advanced age the service life
can be limited. There is a risk of accident,
injury, or property damage. The manufacturer
of the vehicle does not recommend the use of
retreaded tires.
318
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Maximum speed
Changing runflat tires
When changing from runflat tires to standard
tires, it must be ensured that the vehicle con-
tains an emergency wheel or tire mobility kit.
For more information, contact an authorized
service center or another qualified service cen-
ter or repair shop.
Safety information
Warning
If the maximum permissible speed of your
mounted tires is exceeded, the tires may be
damaged. There is a risk of accident, injury,
or property damage. Do not exceed the maxi-
mum permissible speed of the tires.
Wheel change between axles
Warning
A wheel change between the axles on vehi-
cles with different tire sizes or rim sizes on
the front and rear axles can cause damage
to the tires and the vehicle. There is a risk of
accident, injury, or property damage. Do not
rotate the tires between the axles on vehicles
with different tire sizes or rim sizes on the
front and rear axles.
Maximum speed of winter tires
If the maximum speed of the vehicle is higher
than the permissible speed of the winter tires,
the maximum permissible speed must be indi-
cated with a sign placed in the field of vision.
The info label is available from an authorized
service center or another qualified service cen-
ter or repair shop.
Winter tires
Storing tires
General information
Tire pressure
Do not exceed the maximum tire inflation pres-
sure indicated on the tire sidewall.
Storage
▷
Store wheels and tires in a cool, dry and
dark place.
▷
Always protect tires against all contact with
oil, grease, and solvents.
▷
▷
Do not leave tires in plastic bags.
Remove dirt from wheels or tires.
Winter tires are recommended for operating on
winter roads.
Winter tires can be identified by the icon with
mountain and snowflake, as well as the M+S
marking on the tire sidewall.
Runflat tires
Principle
All-season tires with the M+S designation, but
without icon with mountain and snowflake,
have better winter characteristics than summer
tires but generally do not achieve the perform-
ance of winter tires.
Runflat tires permit continued driving under
limited conditions even in the event of a com-
plete tire pressure loss.
319
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
General information
Identification
The wheels consist of tires that are self-sup-
porting to a limited degree and may also in-
clude special rims.
The reinforcement of the sidewall allows the
tire to remain drivable to a limited degree in
the event of a tire pressure loss.
Follow the instructions for continued driving
with a flat tire.
Runflat tires are labeled with a circular icon
containing the letters RSC marked on the tire
sidewall.
Safety information
Warning
The vehicle handles differently when a runflat
tire has insufficient or no tire pressure; for
instance, reduced directional stability when
braking, braking distances are longer and the
self-steering properties will change. There is
a risk of accident, injury, or property damage.
Drive moderately and do not exceed a speed
of 50 mph/80 km/h.
Repairing a flat tire
Safety precautions
▷
Park the vehicle as far away as possible
from passing traffic and on solid ground.
▷
▷
Turn on the hazard warning system.
Secure the vehicle against rolling away by
setting the parking brake.
Warning
▷
▷
▷
Turn the steering wheel until the front
wheels are in the straight-ahead position
and engage the steering wheel lock.
Vibrations or loud noises while driving can
indicate the final failure of a tire. Tire com-
ponents may come loose. There is a risk of
accident, injury, or property damage. Reduce
your speed and stop. Do not continue driving.
Contact an authorized service center or an-
other qualified service center or repair shop.
Have all vehicle occupants get out and
make sure that they remain outside the
hazardous area such as behind a guardrail.
If necessary, set up a warning triangle at an
appropriate distance.
Tire repair set
Principle
The tire repair set is used to temporarily seal
minor tire damage so that it is possible to con-
tinue driving.
320
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Compressor
General information
▷
The filled in tire sealant closes the damage
from the inside when it hardens.
▷
Follow the instructions for using the tire
repair set, which are provided on the com-
pressor and sealant bottle.
▷
▷
The tire repair set may be insufficient if the
tire damage measures more than approx.
0.16 in/4 mm.
Do not remove foreign objects that have
penetrated the tire. Remove foreign objects
only when they are visibly protruding from
the tire.
1
Compressor
2
3
4
5
6
Tire pressure display
Sealant bottle mount
▷
The compressor can be used to check the
tire inflation pressure.
Pressure reducing valve button
Connector for socket
Power switch
Overview
Storage
Safety precautions
Depending on vehicle equipment, the tire re-
pair set is stored as follows:
▷
Park the vehicle as far away as possible
from passing traffic and on solid ground.
▷
In the cargo area under the cargo floor
panel.
▷
▷
▷
Turn on the hazard warning system.
Set the parking brake.
▷
▷
In the cargo area on the left or right side.
In the cargo area behind a side trim panel.
Turn the steering wheel until the front
wheels are in the straight-ahead position
and engage the steering wheel lock.
Sealant bottle and filler hose
▷
As soon as permitted by the traffic flow,
have all vehicle occupants get out and
make sure that they remain outside the
hazardous area such as behind a guardrail.
▷
▷
If necessary, set up the hazard triangle or
hazard warning lights at an appropriate
distance.
Remove the warning label for the maximum
permissible speed from the sealant bottle
and attach it in the visible area in the vehi-
cle interior.
1
Sealant bottle
2
3
4
5
Sealant bottle outlet
Filler hose
Sealant bottle connection
Wheel valve connection
321
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
4. Unscrew the valve cap from the wheel and
screw the connecting piece of the filler hose
onto the valve.
Preparing the tire repair set
1. Insert the sealant bottle into the mount on
the housing of the compressor.
5. With the compressor switched off, insert the
connector into the power socket in the vehi-
cle interior.
2. Turn the sealant bottle clockwise by 90° to
the stop.
Filling the tire with sealing
compound
Safety information
DANGER
If the exhaust pipe is blocked or ventilation is
insufficient, harmful exhaust gases can pene-
trate the vehicle. The exhaust gases contain
pollutants which are colorless and odorless.
In enclosed areas, exhaust gases can also
accumulate outside of the vehicle. There is a
danger to life. Keep the exhaust pipe free and
ensure sufficient ventilation.
3. Connect the filler hose to the outlet of the
sealant bottle and turn clockwise by 90° to
the stop.
NOTICE
The compressor can overheat during ex-
tended operation. There is a risk of damage
to property. Do not run the compressor for
more than 10 minutes.
Filling the tire with sealing compound
1. With standby state or drive-ready state
switched on, switch on the compressor.
322
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Let the compressor run for max. 10 minutes
to fill in the tire sealant and reach a tire
pressure of 2.5 bar/36 psi.
Tire sealant may spray from the damaged
area during the initial wheel rotations.
Adjusting the tire pressure
1. Stop at a suitable location.
While the tire is being filled with tire sealant,
the tire pressure can briefly reach approx.
6 bar/87 psi. Do not turn off the compres-
sor in this phase.
2. Connect the hose directly to the compres-
sor and turn clockwise by 90° until it audi-
bly engages.
2. Switch off the compressor.
3. Unscrew the valve cap from the wheel and
screw the connecting piece of the hose
onto the valve.
Checking the tire pressure
Read the tire pressure on the tire pressure dis-
play of the compressor. The tire pressure must
be at least 2.5 bar/36 psi.
Tire pressure too high
If the tire pressure is too high, reduce the tire
pressure with the pressure reducing valve on
the compressor.
Minimum tire inflation pressure is not
reached
Do not continue driving unless a minimum tire
pressure of 2.5 bar/36 psi is reached. Contact
an authorized service center or another quali-
fied service center or repair shop.
4. Insert the connector into the socket in the
vehicle interior.
5. Read the tire pressure on the tire pressure
display of the compressor.
Do not continue driving unless a minimum
tire pressure of 1.3 bar/19 psi is displayed.
Contact an authorized service center or an-
other qualified service center or repair shop.
Minimum tire inflation pressure is
reached
1. Pull the connector out of the socket in the
vehicle interior.
6. Correct the tire pressure to 2.5 bar/36 psi.
▷
Increase tire pressure: with standby or
drive-ready state turned on, turn on the
compressor and let it run for a maxi-
mum of 10 minutes.
2. Disconnect the hose from the sealant bottle
and the valve on the wheel.
3. Unscrew the valve cap.
4. Stow the tire repair set in the trunk.
▷
Reduce tire pressure: press the pressure
reducing valve button on the compres-
sor.
5. Immediately drive 6 miles/10 km to ensure
that the tire sealant is evenly distributed in
the tire.
Removing and stowing the tire
repair set
1. Switch off the compressor.
Do not exceed the permissible maximum
speed of 50 mph/80 km/h.
If possible, do not drive at speeds less than
12 mph/20 km/h.
2. Pull the connector out of the socket in the
vehicle interior.
323
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
3. Disconnect the hose from the compressor
and the valve on the wheel.
Warning
4. Unscrew the valve cap.
Insufficiently tight snow chains may damage
tires and vehicle components. There is a risk
of accident, injury, or property damage. Make
sure that the snow chains are always suf-
ficiently tight. Re-tighten as needed accord-
ing to the snow chain manufacturer's instruc-
tions.
5. Stow the tire repair set together with the
hose in the trunk.
Continuing the trip
Do not exceed the permissible maximum
speed of 50 mph/80 km/h.
Do not exceed a maximum distance traveled of
125 miles/200 km.
Fine-link snow chains
Re-initialize the flat tire monitor or reset the
Tire Pressure Monitor.
The manufacturer of the vehicle recommends
the use of fine-link snow chains. Certain types
of fine-link snow chains have been tested by
the manufacturer of the vehicle and recom-
mended as road-safe.
Replace the faulty tire and the sealant bottle
from the tire repair set as soon as possible.
Additional information:
For information on suitable snow chains, con-
tact an authorized service center or another
qualified service center or repair shop.
▷
▷
Flat tire monitor, refer to page 332.
Tire pressure monitor, refer to page 325.
System limits
If the tire cannot be made drivable, contact an
authorized service center or another qualified
service center or repair shop.
Use
Use only in pairs on the rear wheels, equipped
with the tires of the following size:
▷
▷
245/45 R18.
245/40 R19.
With the Tire Pressure Monitor: using sealant
can damage the wheel electronics. In this case,
have the electronics checked and replaced at
the next opportunity.
Information on the wheel size and rim offset is
located on the inside of the wheel.
The list can also include wheel/tire sizes that
are only suitable for certain models.
Snow chains
Safety information
Warning
Information on wheels and tires approved for
the vehicle can be requested from an author-
ized service center or another qualified service
center or repair shop.
Follow the snow chain manufacturer's instruc-
tions.
Mounting snow chains on unsuitable tires
can cause the snow chains to come into
contact with vehicle parts. There is a risk of
accident, injury, or property damage. Only
fit snow chains on tires recommended by
the vehicle manufacturer for use with snow
chains.
Do not initialize the flat tire monitor after
mounting snow chains, as doing so may result
in incorrect readings.
Do not reset the Tire Pressure Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
324
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
When driving with snow chains, activate the
Dynamic Traction Control briefly to optimize
the drive power.
Tire pressure monitor
Principle
Maximum speed with snow chains
Do not exceed a speed of 30 mph/50 km/h
when using snow chains.
The Tire Pressure Monitor monitors the tire
pressure and issues a warning if the tire pres-
sure has dropped.
General information
Sensors in the tire valves measure the tire in-
flation pressure and tire temperature.
Rear-wheel steering during
operation with snow chains
General information
Depending on the tires detected or registered,
the system displays the specified nominal
pressures on the control display and compares
them with the current tire pressures.
In order to guarantee free movement of the
wheels when operating with snow chains, rear
axle steering of the integral active steering
must be switched off when snow chains are
mounted.
If tires are being used that are not specified
in the tire inflation pressure details on the ve-
hicle such as tires with special approval, the
system needs to be actively reset. The system
will then take over the actual tire inflation pres-
sures as the target pressures.
Safety information
Warning
When operating the system, also note the in-
formation found in the Tire inflation pressure
chapter.
When rear-wheel steering is switched on and
snow chains are mounted, there can be con-
tact between snow chains and the body.
There is a risk of accident, injury, or property
damage. With mounted snow chains, switch
off the rear-wheel steering.
Additional information:
Tire inflation pressure, refer to page 310.
Safety information
Switching off rear-wheel steering
The rear-wheel steering is switched off by
specifying that snow chains are installed.
Warning
The display of the target pressures is not
a substitute for the tire inflation pressure de-
tails on the vehicle. Incorrect entries in the
tire settings can lead to incorrect target tire
inflation pressure values. In this case, it can-
not be guaranteed that the notification of a
tire pressure loss will be reliable. There is a
risk of injury and risk of damage to property.
Make sure that the sizes of your mounted
tires are displayed correctly and match the
information on the tires and the tire inflation
pressure specifications on the vehicle.
1. "CAR"
2. "Settings"
3. "General settings"
4. "Snow chains"
5. "Snow chains installed"
Starting with the permissible maximum speed
with snow chains of 30 mph/50 km/h the rear
axle steering will be switched on again auto-
matically.
325
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
6. "Manual"
Functional requirements
The following prerequisites must be met for
the system; otherwise, reliable notification of a
tire pressure loss is not assured:
7. "Tire type"
8. Select the tire type that is mounted on the
rear axle.
▷
Every time a tire or wheel is changed, the
correct details on the mounted tires must
be entered in the tire settings.
For tires with special approval:
"Other tires"
Observe further proceeding in the perform
a reset section.
▷
The Tire Pressure Monitor does not acti-
vate until after driving for a few minutes:
9. Select the maximum road speed that will be
used with the tires.
▷
▷
After a tire or wheel change.
After a reset, for tires with special ap-
proval.
10. "Save tire settings"
The measurement of the current tire inflation
pressure is started. The measurement prog-
ress is displayed.
▷
After changing the tire setting.
▷
▷
For tires with special approval:
▷
After a tire or wheel change, a reset was
performed with the correct tire inflation
pressure.
Status display
Current status
The system status can be displayed on the
control display, e.g., whether or not the system
is active.
▷
After the tire inflation pressure was ad-
justed to a new value, a reset was per-
formed.
Wheels with wheel electronics.
1. "CAR"
Tire settings
2. "Vehicle status"
3.
"Tire Pressure Monitor"
General information
The tire sizes of the mounted tires can be
gathered from the tire inflation pressure details
on the vehicle or directly on the tires.
The current status is displayed.
Current tire pressure
The current tire pressure is displayed for each
tire.
The tire details do not need to be re-entered
when the tire pressure is corrected.
The current tire inflation pressures may
change while driving or depending on the out-
side temperature.
For summer and winter tires, the tire details
entered last are stored. After a tire or wheel
change, the settings of the tire sets used last
can be selected.
Current tire temperature
Changing settings
1. "CAR"
Depending on the model, the current tire tem-
peratures are displayed.
The current tire temperatures may change
while driving or due to the outside tempera-
ture.
2. "Vehicle status"
3.
"Tire Pressure Monitor"
4. "Tire settings"
5. "Tire selection"
326
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Nominal pressure
Gray wheels
The nominal pressure for the tires on the front
and rear axles is displayed.
It may not be possible to identify tire pressure
losses.
The specified nominal pressures take the in-
fluence of driving and outside temperature on
the tire temperature into account. The appro-
priate nominal pressure is always displayed,
independent of the weather situation, tire tem-
peratures and travel times.
Possible causes:
▷
▷
Malfunction.
During tire inflation pressure measurement,
after confirmation of the tire settings.
▷
For tires with special approval: a reset is
performed for the system.
The displayed nominal pressure may change
and may differ from the tire inflation pressure
details on the door pillar of the driver's door.
The tire inflation pressure can thus be cor-
rected to the value of the displayed target
pressures.
For tires with special approval:
performing a reset
1. "CAR"
2. "Vehicle status"
The nominal pressure is immediately adjusted
if the vehicle load state is changed in the tire
settings.
3. "Tire Pressure Monitor"
4. Make sure that correct tire settings have
been made.
Tire settings, refer to page 326.
Tire conditions
5. Turn on drive-ready state and do not drive
off.
General information
Tire and system status are indicated by the
color of the wheels and a text message on the
control display.
6. Reset tire pressure: "Perform reset".
7. Drive off.
The wheels are displayed in gray and the fol-
lowing is displayed: "Resetting tire pressure…".
Any existing messages may not be deleted if
the nominal pressure is not reached after the
tire inflation pressure is corrected.
After a travel time of several minutes, the set
tire inflation pressures are accepted as the
predefined tire inflation pressures. The reset is
completed automatically while driving.
All wheels green
▷
The system is active and bases warnings
on the target pressures.
After a successfully completed reset, the
wheels on the control display are shown in
green and the following is displayed: "Reset
successful."
▷
For tires with special approval: the system
is active and bases warnings on the tire
inflation pressures stored during the last re-
set.
You may interrupt this trip at any time. When
you continue driving the reset resumes auto-
matically.
One to four yellow wheels
A flat tire or major tire pressure loss has occur-
red in the indicated tires.
327
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
If the tire inflation pressure is too low
Messages: for tires without special
approval
Message
General information
When a flat tire is indicated, the Dynamic Sta-
bility Control may be turned on.
A yellow warning light is illuminated in
the instrument cluster.
In addition, an icon with a Check Control mes-
sage appears on the control display.
Safety information
Icon
Possible cause
Warning
There is a tire pressure loss.
A damaged regular tire with low or no tire
inflation pressure impacts handling such as
steering and braking response. Runflat tires
can maintain limited stability. There is a risk
of accident. Do not continue driving if the
vehicle is equipped with normal tires. Follow
the information on runflat tires and continued
driving with these tires.
Measure
1. Reduce the vehicle speed. Do not exceed a
speed of 80 mph/130 km/h.
2. At the next opportunity, for instance at a fill-
ing station, check the tire inflation pressure
in all four tires and correct if necessary.
If a tire inflation pressure check is
required
If there is a significant tire pressure
loss
Message
Message
An icon with a Check Control message appears
on the control display.
A yellow warning light is illuminated in
the instrument cluster.
Icon
Possible cause
In addition, an icon with the affected tire ap-
pears in a Check Control message on the con-
trol display.
Leak detected on the tire.
Inflation was not carried out accord-
ing to specifications, for instance
when the tire has not been suffi-
ciently inflated or in the case of a nat-
ural steady tire pressure loss.
Icon
Possible cause
There is a flat tire or a major tire
pressure loss.
Measure
Measure
Check the tire pressure and correct as needed.
1. Reduce your speed and stop cautiously.
Avoid sudden braking and steering maneu-
vers.
2. Check whether the vehicle is fitted with
standard tires or runflat tires.
328
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Runflat tires are labeled with a circular icon
containing the letters RSC marked on the
tire sidewall.
Icon
Possible cause
Inflation was not carried out accord-
ing to specifications, e.g., the tire has
not been sufficiently inflated.
Runflat tires, refer to page 319.
3. Read the description on what to do in case
of a flat tire.
The system has detected a wheel
change, but no reset was done.
Actions in the event of a flat tire, refer to
page 330.
The tire inflation pressure has fallen
below the level of the last reset.
No reset was performed for the sys-
tem. The system issues a warning
based on the tire inflation pressures
stored during the last reset.
Messages: for tires with special
approval
General information
When a flat tire is indicated, the Dynamic Sta-
bility Control may be turned on.
Measure
1. Check the tire pressure and correct as
needed.
Safety information
2. Perform a system reset.
If the tire inflation pressure is too low
Message
Warning
A damaged regular tire with low or no tire
inflation pressure impacts handling such as
steering and braking response. Runflat tires
can maintain limited stability. There is a risk
of accident. Do not continue driving if the
vehicle is equipped with normal tires. Follow
the information on runflat tires and continued
driving with these tires.
A yellow warning light is illuminated in
the instrument cluster.
In addition, an icon with a Check Control mes-
sage appears on the control display.
Icon
Possible cause
There is a tire pressure loss.
If a tire inflation pressure check is
required
No reset was performed for the sys-
tem. The system issues a warning
based on the tire inflation pressures
stored during the last reset.
Message
An icon with a Check Control message appears
on the control display.
Measure
1. Reduce the vehicle speed. Do not exceed a
speed of 80 mph/130 km/h.
2. At the next opportunity, for instance at a fill-
ing station, check the tire inflation pressure
in all four tires and correct if necessary.
3. Reset the system.
329
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
For tires with special approval: when the
tire pressure in all four tires is correct, the
Tire Pressure Monitor may not have been
reset. In this case, perform the reset.
If there is a significant tire pressure
loss
Message
If no tire damage can be identified, con-
tact an authorized service center or another
qualified service center or repair shop.
A yellow warning light is illuminated in
the instrument cluster.
In addition, an icon with the affected tire ap-
pears in a Check Control message on the con-
trol display.
2. Repair the flat tire, e.g., with a flat tire kit or
by changing the wheel.
Use of sealing compound, for instance from
the flat tire kit, may damage the wheel elec-
tronics. Have the electronics replaced at the
next opportunity.
Icon
Possible cause
There is a flat tire or a major tire
pressure loss.
Runflat tires
No reset was performed for the sys-
tem. The system issues a warning
based on the tire inflation pressures
stored during the last reset.
Safety information
Warning
Measure
The vehicle handles differently when a runflat
tire has insufficient or no tire pressure; for
instance, reduced directional stability when
braking, braking distances are longer and the
self-steering properties will change. There is
a risk of accident, injury, or property damage.
Drive moderately and do not exceed a speed
of 50 mph/80 km/h.
1. Reduce your speed and stop cautiously.
Avoid sudden braking and steering maneu-
vers.
2. Check whether the vehicle is fitted with
standard tires or runflat tires.
Runflat tires are labeled with a circular icon
containing the letters RSC marked on the
tire sidewall.
Runflat tires, refer to page 319.
Warning
3. Read the description on what to do in case
of a flat tire.
Vibrations or loud noises while driving can
indicate the final failure of a tire. Tire com-
ponents may come loose. There is a risk of
accident, injury, or property damage. Reduce
your speed and stop. Do not continue driving.
Contact an authorized service center or an-
other qualified service center or repair shop.
Actions in the event of a flat tire, refer to
page 330.
Actions in the event of a flat tire
Standard tires
1. Identify the damaged tire.
Maximum speed
Check the tire pressure in all four tires,
for instance using the tire pressure display
of a flat tire kit.
You may continue driving with a damaged tire
at speeds up to 50 mph/80 km/h.
330
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Continued driving with a flat tire
The tire inflation pressure is reduced when the
tire temperature falls again.
Follow the following when continuing to drive
with a damaged tire:
These circumstances may cause a warning
when temperatures fall very sharply.
1. Avoid sudden braking and steering maneu-
vers.
Following a temperature-related warning, the
target pressures are displayed on the control
display again after a short distance.
2. Do not exceed a speed of
50 mph/80 km/h.
3. Check the tire inflation pressure in all four
tires at the next opportunity.
Sudden tire pressure loss
The system cannot indicate sudden serious
tire damage caused by external circumstances.
Possible distance traveled with a
depressurized tire
Failure performing a reset
The possible distance traveled varies depend-
ing on how the vehicle is loaded and used, e.g.,
speed, road conditions, outside temperature.
The distance traveled may be less but may
also be more if an economical driving style is
used.
Tires with special approval: the system will not
function correctly if a reset was not performed,
for example a flat tire may be indicated al-
though the tire inflation pressures are correct.
Malfunction
If the vehicle is loaded with an average
weight and used under favorable conditions,
the possible distance traveled may be up to
50 miles/80 km.
Message
The yellow warning light flashes and is
then illuminated continuously. A Check
Control message is displayed. It may
Vehicle handling with damaged tires
not be possible to identify tire pressure losses.
Vehicles driven with a damaged tire will han-
dle differently, potentially leading to conditions
such as the following:
Measure
▷
▷
▷
Greater likelihood of skidding of the vehicle.
Longer braking distances.
▷
A wheel without wheel electronics is
mounted: have the wheels checked, if
needed.
Changed self-steering properties.
▷
Fault caused by systems or devices with
the same radio frequency: after leaving the
area of the interference, the system auto-
matically becomes active again.
Modify your driving style. Avoid abrupt steering
or driving over obstacles, for instance curbs or
potholes.
▷
▷
For tires with special approval: the system
was unable to complete the reset. Perform
a system reset again.
System limits
Temperature
The tire inflation pressure depends on the
tire's temperature.
Tire Pressure Monitor malfunction: have
the vehicle checked by an authorized serv-
ice center or another qualified service cen-
ter or repair shop.
Driving or exposure to the sun will increase the
tire temperature, thus increasing the tire infla-
tion pressure.
331
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
vehicle that prevent the TPMS from function-
ing properly. Always check the TPMS malfunc-
tion telltale after replacing one or more tires
or wheels on the vehicle to ensure that the re-
placement or alternate tires and wheels allow
the TPMS to continue to function properly.
Declaration according to NHTSA/
FMVSS 138 Tire Pressure Monitoring
System
Each tire, including the spare (if provided)
should be checked monthly when cold and in-
flated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If the
vehicle has tires of a different size than the
size indicated on the vehicle placard or tire
inflation pressure label, you should determine
the proper tire inflation pressure for those
tires.) As an added safety feature, the vehi-
cle has been equipped with a tire pressure
monitoring system (TPMS) that illuminates a
low tire pressure telltale when one or more
of your tires is significantly under-inflated. Ac-
cordingly, when the low tire pressure telltale
illuminates, you should stop and check your
tires as soon as possible, and inflate them to
the proper pressure. Driving on a significantly
under-inflated tire causes the tire to overheat
and can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life, and
may affect the vehicle's handling and stopping
ability. Please note that the TPMS is not a
substitute for proper tire maintenance, and it
is the driver's responsibility to maintain correct
tire pressure, even if under-inflation has not
reached the level to trigger illumination of the
TPMS low tire pressure telltale. The vehicle
has also been equipped with a TPMS malfunc-
tion indicator to indicate when the system is
not operating properly. The TPMS malfunction
indicator is combined with the low tire pres-
sure telltale. When the system detects a mal-
function, the telltale will flash for approximately
one minute and then remain continuously il-
luminated. This sequence will continue upon
subsequent vehicle start-ups as long as the
malfunction exists. When the malfunction indi-
cator is illuminated, the system may not be
able to detect or signal low tire pressure as
intended. TPMS malfunctions may occur for a
variety of reasons, including the installation of
replacement or alternate tires or wheels on the
Flat tire monitor
Principle
The flat tire monitor detects a tire pressure
loss while driving and issues a warning if the
tire pressure has dropped.
General information
The system detects tire pressure loss on the
basis of rotation speed differences between
the individual wheels while driving.
In the event of a tire pressure loss, the diam-
eter and therefore the rate of rotation of the
corresponding wheel changes. The difference
will be detected and reported as a flat tire.
The system does not measure the actual infla-
tion pressure in the tires.
Functional requirements
The following prerequisites must be met for
the system; otherwise, reliable notification of a
tire pressure loss is not assured:
▷
After a tire or wheel change, an initialization
was performed with the correct tire inflation
pressure.
▷
After the tire pressure was adjusted to a
new value, an initialization was performed.
332
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
Safety information
Status display
The current status of the flat tire monitor can
be displayed, e.g., whether the flat tire monitor
is active.
Warning
A damaged regular tire with low or no tire
inflation pressure impacts handling such as
steering and braking response. Runflat tires
can maintain limited stability. There is a risk
of accident. Do not continue driving if the
vehicle is equipped with normal tires. Follow
the information on runflat tires and continued
driving with these tires.
1. "CAR"
2. "Vehicle status"
3.
"Flat Tire Monitor"
The status is displayed.
Initialization required
An initialization must be performed in the fol-
lowing situations:
Indication of a flat tire
▷
After the tire inflation pressure has been
adjusted.
A yellow warning light is illuminated in
the instrument cluster.
▷
After a tire or wheel change.
In addition, an icon with a Check Control mes-
sage appears on the control display.
Performing initialization
When initializing, the set tire inflation pressures
serve as reference values in order to detect a
flat tire. Initialization is started by confirming
the tire inflation pressures.
Icon
Possible cause
There is a flat tire or a major tire
pressure loss.
Do not initialize the system when driving with
snow chains.
Measure
1. "CAR"
1. Reduce your speed and stop cautiously.
Avoid sudden braking and steering maneu-
vers.
2. "Vehicle status"
3. "Flat Tire Monitor"
2. Check whether the vehicle is fitted with
standard tires or runflat tires.
4. Turn on drive-ready state and do not drive
off.
Runflat tires are labeled with a circular icon
containing the letters RSC marked on the
tire sidewall.
5. Start the initialization with: "Perform reset"
6. Drive off.
The initialization is completed while driving,
which can be interrupted at any time.
Runflat tires, refer to page 319.
The initialization automatically continues when
driving continues.
Actions in the event of a flat tire
Standard tires
1. Identify the damaged tire.
Messages
To do this, check the tire pressure in all four
tires, for instance using the tire pressure
display of a flat tire kit.
General information
When a flat tire is indicated, the Dynamic Sta-
bility Control (DSC) is turned on, if needed.
333
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
When the tire inflation pressure in all four
tires is correct, the flat tire monitor may not
have been initialized. In this case, initialize
the system.
Continued driving with a flat tire
Follow the following when continuing to drive
with a damaged tire:
1. Avoid sudden braking and steering maneu-
vers.
If tire damage cannot be identified, contact
an authorized service center or another
qualified service center or repair shop.
2. Do not exceed a speed of
50 mph/80 km/h.
2. Repair the flat tire, e.g., with a flat tire kit or
by changing the wheel.
3. Check the tire inflation pressure in all four
tires at the next opportunity.
Runflat tires
When the tire inflation pressure in all four
tires is correct, the flat tire monitor may not
have been initialized. In this case, initialize
the system.
Safety information
Warning
Possible distance traveled with a
depressurized tire
The vehicle handles differently when a runflat
tire has insufficient or no tire pressure; for
instance, reduced directional stability when
braking, braking distances are longer and the
self-steering properties will change. There is
a risk of accident, injury, or property damage.
Drive moderately and do not exceed a speed
of 50 mph/80 km/h.
The possible distance traveled varies depend-
ing on how the vehicle is loaded and used, e.g.,
speed, road conditions, outside temperature.
The distance traveled may be less but may
also be more if an economical driving style is
used.
If the vehicle is loaded with an average
weight and used under favorable conditions,
the possible distance traveled may be up to
50 miles/80 km.
Warning
Vibrations or loud noises while driving can
indicate the final failure of a tire. Tire com-
ponents may come loose. There is a risk of
accident, injury, or property damage. Reduce
your speed and stop. Do not continue driving.
Contact an authorized service center or an-
other qualified service center or repair shop.
Vehicle handling with damaged tires
Vehicles driven with a damaged tire will han-
dle differently, potentially leading to conditions
such as the following:
▷
▷
▷
Greater likelihood of skidding of the vehicle.
Longer braking distances.
Changed self-steering properties.
Maximum speed
Modify your driving style. Avoid abrupt steering
or driving over obstacles, for instance curbs or
potholes.
You may continue driving with a damaged tire
at speeds up to 50 mph/80 km/h.
System limits
The system could be delayed or malfunction in
the following situations:
334
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
▷
▷
A natural, even tire pressure loss in all
four tires will not be recognized. Therefore,
check the tire inflation pressure regularly.
Warning
Placing supports, e.g., wooden blocks or sim-
ilar, under the jack may reduce its ability to
bear weight because of the limited height.
The load-carrying capacity of the wooden
blocks may be exceeded and the vehicle may
tip over. There is a risk of injury or danger to
life. Do not place supports under the jack.
Sudden serious tire damage caused by ex-
ternal circumstances cannot be recognized
in advance.
▷
▷
▷
The system has not been initialized.
When driving on a snowy or slippery road.
Sporty driving style: slip on traction wheels,
high lateral acceleration (drifting).
▷
When driving with snow chains.
Warning
The jack, issued by the vehicle manufacturer,
is provided in order to perform a wheel
change in the event of a breakdown. The
jack is not designed for frequent use, e.g.,
changing from summer to winter tires. Using
the jack frequently may cause it to become
jammed or damaged. There is a risk of injury
and risk of damage to property. Only use the
jack to change an emergency or spare wheel
in the event of a breakdown.
Changing wheels/tires
General information
When using runflat tires or a flat tire kit, a
wheel does not always need to be changed
immediately in case of a breakdown when
there is a tire pressure loss due to a flat tire.
If necessary, a suitable wheel change tool, e.g.,
a jack, is available as an accessory from an
authorized service center or another qualified
service center or repair shop.
Warning
The jack may slip on soft, uneven, or slippery
ground, e.g., snow, ice, tiles, etc. There is a
risk of injury. If possible, change the wheel on
a flat, solid, slip-resistant surface.
Safety information
Warning
The jack is only provided for short-term lifting
of the vehicle for wheel changes. Even if all
safety precautions are observed, there is a
risk of the raised vehicle falling if the jack tips
over. There is a risk of injury or danger to life.
When the vehicle is raised with the jack, do
not lie under the vehicle and do not switch on
the drive-ready state.
Warning
The jack is optimized for lifting the vehicle
and for the jacking points on the vehicle only.
There is a risk of injury. Do not lift any other
vehicle or cargo using the jack.
Warning
When the jack is not inserted into the jacking
point provided for this purpose, the vehicle
may be damaged or the jack may slip when
it is being cranked up. There is a risk of injury
335
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
or risk of damage to property. When cranking
up the jack, ensure that it is inserted in the
jacking point next to the wheel well.
On a level surface
Warning
A vehicle that is raised on a jack may fall
off of the jack if lateral forces are exerted on
it. There is a risk of injury and risk of dam-
age to property. While the vehicle is raised,
do not exert lateral effort on the vehicle or
pull abruptly on the vehicle. Have a stuck
wheel removed by an authorized service cen-
ter or another qualified service center or re-
pair shop.
Place chocks or other suitable objects in front
and behind the wheel that is diagonal to the
wheel being changed.
On a slight downhill gradient
NOTICE
Using an impact wrench to loosen or tighten
the wheel lock bolt can damage the wheel
lock bolt. There is a risk of damage to prop-
erty. Only use a lug wrench to loosen and
tighten the wheel lock bolt.
Securing the vehicle against rolling
away
If it is necessary to change a wheel on a slight
downhill gradient, place chocks and other suit-
able objects, e.g., rocks, under the wheels of
the front and rear axles, against the direction
that the vehicle will move.
General information
The vehicle manufacturer recommends to ad-
ditionally secure the vehicle against rolling
away when changing a wheel.
Lug bolt lock
Principle
The wheel lug bolts have a special coding. The
lug bolts can only be released with the adapter
which matches the coding.
Overview
Depending on vehicle equipment, store the lug
bolt lock adapter as follows:
336
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
▷
In the cargo area under the cargo floor
panel.
make sure that they remain outside the
hazardous area such as behind a guardrail.
▷
▷
In the cargo area on the left or right side.
In the cargo area behind a side trim panel.
▷
▷
Depending on the vehicle equipment, get
wheel change tools and, if necessary, the
emergency wheel from the vehicle.
If necessary, set up a warning triangle or
portable hazard warning light at an appro-
priate distance.
▷
▷
Secure the vehicle additionally against roll-
ing away.
Loosen the lug bolts a half turn.
Jacking points
▷
▷
Lug lock bolt, arrow 1.
Adapter, arrow 2.
Unscrewing
1. Attach the adapter to the lug lock bolt.
2. Unscrew the lug lock bolt.
3. Remove the adapter after unscrewing the
lug bolt.
The jacking points are located at the indicated
positions.
Screwing on
1. Attach the adapter to the lug lock bolt. If
necessary, turn the adapter until it fits on
the lug lock bolt.
Jacking up the vehicle
2. Screw on the lug lock bolt. The tightening
torque is 101 lbs ft/140 Nm.
Warning
Hands and fingers can be jammed when us-
ing the jack. There is a risk of injury. Comply
with the described hand position and do not
change this position while using the jack.
3. Remove the adapter and stow it after
screwing on the lug bolt.
Preparing the vehicle
▷
Park the vehicle on solid and non-slip
ground at a safe distance from road traffic.
▷
▷
▷
Turn on the hazard warning system.
Set the parking brake.
Engage a gear or move the selector lever to
position P.
▷
As soon as permitted by the traffic flow,
have all vehicle occupants get out and
337
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
5. Make sure that the car jack foot extends
vertically and is at a right angle beneath the
jacking point.
1. Hold the vehicle jack with one hand, ar-
row 1, and grasp the jack crank handle or
lever with your other hand, arrow 2.
6. Crank the vehicle up until the vehicle jack
has the entire surface on the ground
and the relevant wheel is maximum 1.2 in-
ches/3 cm above ground.
2. Insert the jack into the rectangular recess of
the jacking point closest to the wheel to be
changed.
Mounting a wheel
Mount one emergency wheel only, as required.
1. Unscrew the lug bolts.
2. Remove the wheel.
3. Put the new wheel or emergency wheel on
and screw in at least two lug bolts in a
crosswise pattern until hand-tight.
3. Extend the jack by turning the jack crank
handle or lever clockwise.
When non-original light-alloy wheels of the
vehicle manufacturer are mounted, the ac-
companying lug bolts may have to be used
as well.
4. Hand-tighten the remaining lug bolts and
tighten all lug bolts well in a crosswise pat-
tern.
5. Turn the jack crank handle counterclock-
wise to retract the jack and lower the vehi-
cle.
6. Remove the jack and stow it securely.
4. Take your hand away from the jack as soon
as the jack is under load and continue turn-
ing the jack crank handle or lever with one
hand.
After the wheel change
1. Tighten the lug bolts crosswise. The tight-
ening torque is 101 lbs ft/140 Nm.
2. Stow the faulty wheel in the cargo area, if
necessary.
338
Online Edition for Part no. 01405B381F1 - II/24
Wheels and tires
MOBILITY
3. Check tire inflation pressure at the next op-
portunity and correct as needed.
4. Re-initialize the flat tire monitor or reset the
Tire Pressure Monitor.
5. Check to make sure the lug bolts are tight
with a calibrated torque wrench.
6. Drive to the nearest authorized service cen-
ter or another qualified service center or
repair shop, then have the damaged tire
replaced.
339
Online Edition for Part no. 01405B381F1 - II/24
Engine compartment
MOBILITY
Engine compartment
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
Vehicle features and options
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
Overview
6-cylinder engine
1
Filler neck for washer fluid
Jump-starting, positive battery terminal
Oil filler neck
5
6
7
Coolant reservoir, auxiliary cooling
Jump-starting, negative battery terminal
Vehicle identification number
2
3
4
Coolant reservoir, engine
340
Online Edition for Part no. 01405B381F1 - II/24
Engine compartment
MOBILITY
8-cylinder engine
1
Filler neck for washer fluid
5
6
7
Oil filler neck
2
3
4
Jump-starting, positive battery terminal
Coolant reservoir, engine
Jump-starting, negative battery terminal
Vehicle identification number
Coolant reservoir, auxiliary cooling
Hood
Warning
The engine compartment accommodates
moving components. Certain components in
the engine compartment can also move with
the vehicle switched off, for instance the radi-
ator fan. There is a risk of injury. Do not reach
into the area of moving parts. Keep articles of
clothing and hair away from moving parts.
Safety information
Warning
Improperly executed work in the engine com-
partment can damage components and lead
to a safety hazard. There is a risk of acci-
dent, injury, or property damage. The vehi-
cle manufacturer recommends having work
in the engine compartment performed by an
authorized service center or another qualified
service center or repair shop.
Warning
There are protruding parts, for instance lock-
ing hooks, on the inside of the hood. There
is a risk of injury. If the hood is open, pay
attention to protruding parts and keep clear
of these areas.
341
Online Edition for Part no. 01405B381F1 - II/24
Engine compartment
MOBILITY
Warning
Opening hood
1. Pull lever, arrow 1. Hood is unlocked.
An incorrectly locked hood can open while
driving and restrict visibility. There is a risk
of accident, injury, or property damage. Stop
immediately and correctly close the hood.
Warning
Body parts can be jammed when opening
and closing the hood. There is a risk of in-
jury. Make sure that the area of movement of
hood is clear while opening and closing.
2. After the lever is released, pull the lever
again, arrow 2.
Hood can be opened.
3. Be careful of protruding parts on the hood.
NOTICE
Folded-out wipers can be jammed when the
hood is opened. There is a risk of damage to
property. Make sure that the wipers with the
wiper blades mounted are folded down onto
the windshield before opening the hood.
Closing the hood
NOTICE
When the hood is closed, it must engage on
both sides. Pressing again can damage the
hood. There is a risk of damage to property.
Open the hood again and then close it ener-
getically. Avoid pressing again.
Energetically close the hood from approx.
20 in/50 cm.
The hood must engage on both sides.
342
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
MOBILITY
Operating materials
Safety information
Vehicle features and options
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
Caution
The use of poor-quality fuels may result in
harmful engine deposits or damage. Addi-
tionally, problems relating to drivability, start-
ing and stalling, especially under certain envi-
ronmental conditions such as high ambient
temperature and high altitude, may occur.
If drivability problems are encountered, we
recommend switching to a high quality gaso-
line brand and a higher octane grade — AKI
number — for a few tank fills. To avoid harm-
ful engine deposits, it is highly recommended
to purchase gasoline from Top Tier retailers.
Fuel recommendation
General information
Failure to comply with these recommenda-
tions may result in the need for additional
maintenance.
Depending on the region, many filling stations
sell fuel that has been customized to winter
or summer conditions. Fuel that is available
in winter, for instance helps make a cold start
easier.
Warning
Even small quantities of the wrong fuel or
wrong fuel additives can damage the fuel
system and engine. Furthermore, the cata-
lytic converter can be permanently damaged.
There is a risk of injury and risk of damage to
property. Do not refuel or add the following in
the case of gasoline engines:
Gasoline
General information
For the best fuel efficiency, the gasoline should
be sulfur-free or very low in sulfur content.
Fuels that are marked on the gas pump as
containing metal must not be used.
▷
▷
Leaded gasoline.
Fill up using fuel with a maximum ethanol con-
tent of 10 %, e.g., E10.
Metallic additives, for instance manga-
nese or iron.
To achieve nominal values for mileage and
consumption, follow the specified fuel quality
in the sales literature.
Do not turn on standby after refueling with
the wrong fuel. Contact an authorized service
center or another qualified service center or
repair shop.
When using minimum quality fuel like RON 91
or fuel with an ethanol content of more than
10 % to max. 25 %, knocking noises may oc-
cur and driving and acoustic performance may
change. These have no effect on the engine
service life.
343
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
MOBILITY
NOTICE
Engine oil
Fuel that does not meet the minimum quality
requirements can cause the engine to mal-
function or become damaged. There is a risk
of damage to property. Do not fill with fuel
that does not comply with the minimum qual-
ity.
General information
The engine oil consumption is dependent on
your driving style and driving conditions.
Therefore, regularly check the engine oil level
after refueling by taking a detailed measure-
ment.
The engine oil consumption can increase in
the following situations, for instance:
NOTICE
▷
▷
▷
▷
Sporty driving style.
Incorrect fuels can damage the fuel system
and the engine. There is a risk of damage
to property. Do not use fuels with a higher
ethanol content than recommended. Do not
refuel with fuels containing methanol, e.g. M5
to M100.
Break-in of the engine.
Idle operation of the engine.
With use of engine oil types that are not
recommended.
Different Check Control messages appear on
the control display depending on the engine oil
level.
Recommended gas quality
BMW recommends AKI 91.
M Performance model:
The vehicle manufacturer recommends having
the engine oil changed by an authorized serv-
ice center or another qualified service center
or repair shop. The suitable viscosity grade is
indicated on a sign in the engine compartment.
BMW recommends AKI 93.
Minimum fuel grade
BMW recommends AKI 87.
Safety information
If you use gasoline with this minimum AKI Rat-
ing, the engine may produce knocking sounds
when starting at high external temperatures.
This has no effect on the engine life.
NOTICE
An engine oil level that is too low causes en-
gine damage. There is a risk of damage to
property. Immediately add engine oil.
NOTICE
Too much engine oil can damage the engine
or the catalytic converter. There is a risk of
damage to property. Do not add too much
engine oil. If there is excess engine oil, have
the engine oil level corrected by an author-
ized service center or another qualified serv-
ice center or repair shop.
344
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
System limits
MOBILITY
NOTICE
When making frequent short-distance trips or
using a sporty driving style, it may not be pos-
sible to calculate a measured value. In this
case, the measured value for the last, suffi-
ciently long trip is displayed.
Engine oil that is not changed in timely fash-
ion can cause increased engine wear and
thus engine damage. There is a risk of dam-
age to property. It is recommended that you
do not exceed the service intervals indicated
in the vehicle.
Detailed measurement
Principle
Electronic oil measurement
The engine oil level is checked when the vehi-
cle is stationary and displayed via a scale.
General information
The electronic oil measurement has two
measuring principles:
If the engine oil level is outside its permissible
operating range, a Check Control message is
displayed.
▷
▷
Monitoring.
General information
Detailed measurement.
During the measurement, the idle speed is in-
creased somewhat.
When making frequent short-distance trips or
using a sporty driving style, for instance when
cornering aggressively, regularly perform a de-
tailed measurement.
Functional requirements
▷
▷
Vehicle is parked in a horizontal position.
Monitoring
Selector lever in selector lever position N or
P and accelerator pedal not depressed.
Principle
▷
▷
The drive-ready state is switched on by
pressing the Start/Stop button.
The engine oil level is monitored electronically
while driving and can be shown on the control
display.
The engine is at operating temperature.
If the engine oil level is outside its permissible
operating range, a Check Control message is
displayed.
Performing a detailed measurement
1. "CAR"
2. "Vehicle status"
3.
"Engine oil level"
Functional requirements
4. "Engine oil measurement"
5. "Start measurement"
A current measured value is available after ap-
prox. 30 minutes of normal driving.
The engine oil level is checked and displayed
via a scale.
Displaying the engine oil level
1. "CAR"
2. "Vehicle status"
Adding engine oil
3.
"Engine oil level"
General information
The engine oil level is displayed.
Only add engine oil when the message is dis-
played in the instrument cluster. The top-up
345
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
MOBILITY
quantity is indicated in the message shown on
the control display.
Adding engine oil
1. Opening the hood.
Only add suitable types of engine oil.
Opening, refer to page 342.
2. Open the lid counterclockwise.
Safely park the vehicle and switch off drive-
ready state before adding engine oil.
Take care not to add too much engine oil.
Safety information
Warning
Operating fluids, e.g., oil, grease, coolant,
fuel, may contain harmful ingredients. There
is a risk of injury or danger to life. Follow
the instructions on the containers. Do not
allow operating fluids to come into contact
with your clothing, skin, or eyes. Do not fill
operating fluids into different bottles. Store
operating fluids out of reach of children.
3. Add engine oil.
4. Close the lid.
Engine oil types to add
General information
The engine oil grade is critical for the service
life of the engine.
NOTICE
An engine oil level that is too low causes en-
gine damage. There is a risk of damage to
property. Immediately add engine oil.
Only add with the types of engine oil which are
listed.
Safety information
NOTICE
NOTICE
Too much engine oil can damage the engine
or the catalytic converter. There is a risk of
damage to property. Do not add too much
engine oil. If there is excess engine oil, have
the engine oil level corrected by an author-
ized service center or another qualified serv-
ice center or repair shop.
Oil additives can damage the engine. There
is a risk of damage to property. Do not use oil
additives.
NOTICE
Incorrect engine oil can cause malfunctions
in the engine or damage it. There is a risk
of damage to property. When selecting an
engine oil, make sure that the engine oil has
the correct oil specification.
Overview
The oil filler neck is located in the engine com-
partment.
Additional information:
For an overview, refer to page 340.
346
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
MOBILITY
Suitable engine oil types
When topping up engine oil, the following oil
specification applies:
Coolant
General information
Coolant consists of water and coolant additive.
Gasoline engine
Not all commercially available coolant addi-
tives are suitable for the vehicle. The vehicle
manufacturer recommends using coolant with
the BMW LC-18 specification. Do not mix cool-
ant additives of different colors. Use a 50:50
mixing ratio of water to coolant additive. Infor-
mation on suitable coolant additives can be
provided by an authorized service center or
another qualified service center or repair shop.
BMW Longlife-01 FE.
BMW Longlife-17 FE+.
The BMW Longlife-17 FE+ oil specification is
not suitable for the 50i gasoline engine.
Alternative engine oil types
If an engine oil suitable for continuous use
is not available, up to 1 US quart/liter of an
engine oil with the following oil rating can be
added:
Safety information
Oil specification
API SL.
Warning
With the engine hot and the cooling system
open, coolant can escape and lead to scald-
ing. There is a risk of injury. Only open the
cooling system with the engine cooled down.
API SM.
API SN.
Viscosity grades
Warning
When selecting an engine oil, make sure that
the engine oil has a suitable viscosity grade.
The suitable viscosity grade is indicated on a
sign in the engine compartment.
Additives are harmful and incorrect additives
can damage the engine. There is a risk of
injury and risk of damage to property. Do not
allow additives to come into contact with skin,
eyes or articles of clothing. Use suitable addi-
tives only.
More information about suitable oil specifica-
tions and engine oil viscosity grades can be
requested from an authorized service center or
another qualified service center or repair shop.
NOTICE
Too much water reduces the cooling and an-
tifreeze properties of the coolant. There is a
risk of damage to property. Use a 50:50 mix-
ing ratio of water to coolant additive.
347
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
MOBILITY
6. The coolant is at the correct level if it is be-
Coolant level
tween the minimum and maximum marks
on the filler neck.
General information
Depending on the motorization, there are up to
two coolant reservoirs in the engine compart-
ment. Check and add the coolant levels on a
regular basis.
The coolant reservoir may be overfilled with
coolant when the vehicle is delivered from the
factory or following maintenance and repair
work. The specified coolant level is achieved
with longer operating periods.
7. Close the lid.
The coolant level is indicated using minimum
and maximum marks in the filler neck of the
coolant reservoir.
Adding coolant
1. Let the engine cool down.
2. Turn off the climate control system.
Climate control, refer to page 268.
3. Opening the hood.
Depending on the motorization, the coolant
reservoir is located on the right side or the left
side of the engine compartment.
Additional information:
For an overview, refer to page 340.
Opening, refer to page 342.
4. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres-
sure to dissipate, then open it.
Checking the coolant level
1. Let the engine cool down.
2. Turn off the climate control system.
Climate control, refer to page 268.
3. Opening the hood.
5. Open the coolant reservoir lid.
6. If the coolant is low, slowly add coolant up
to the specified fill level; do not overfill.
Opening, refer to page 342.
7. Close the lid.
4. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres-
sure to dissipate, then open it.
Disposal
Comply with the relevant environmen-
tal protection regulations when dispos-
ing of coolant and coolant additives.
5. Open the coolant reservoir lid.
Washer fluid
General information
All windshield washer jets are supplied from
one tank.
Use a mixture of tap water and windshield
washer concentrate. If desired, a windshield
348
Online Edition for Part no. 01405B381F1 - II/24
Operating materials
MOBILITY
washer concentrate containing antifreeze can
be used.
NOTICE
Recommended minimum fill quantity:
0.2 US gal/1 liter.
Mixing different windshield washer fluid con-
centrates or antifreeze can damage the
washer system. There is a risk of damage
to property. Do not mix different windshield
washer fluid concentrates or antifreeze. Fol-
low the information and mixture ratios pro-
vided on the containers.
Safety information
Warning
Some types of antifreeze can contain harmful
substances and are flammable. There is a
risk of fire and an injury hazard. Follow the in-
structions on the containers. Keep antifreeze
away from ignition sources. Do not fill operat-
ing fluids into different bottles. Store operat-
ing fluids out of reach of children.
Overview
United States: the washer fluid mixture ratio
is regulated by the U.S. EPA and many in-
dividual states; do not exceed the allowable
washer fluid dilution ratio limits that apply.
Follow the usage instructions on the washer
fluid container.
The washer fluid reservoir is located in the en-
gine compartment.
Use of BMW’s Windshield Washer Concen-
trate or the equivalent is recommended.
Malfunction
The use of undiluted windshield washer fluid
concentrate or alcohol-based antifreeze can
lead to incorrect readings at temperatures be-
low +5 ℉/-15 ℃.
Warning
Washer fluid can ignite and catch fire on con-
tact with hot engine parts. There is a risk of
injury or risk of damage to property. Only add
washer fluid when the engine is cooled down.
Next, fully close the lid of the washer fluid
reservoir.
NOTICE
Silicon-containing additives in the washer
fluid for the water-repelling effect on the win-
dows can lead to damage to the car wash.
There is a risk of damage to property. Do
not add silicon-containing additives to the
washer fluid.
349
Online Edition for Part no. 01405B381F1 - II/24
Maintenance
MOBILITY
Maintenance
General information
Information on service notifications can be dis-
played on the control display.
Vehicle features and options
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
Additional information:
Service notifications, refer to page 166.
Service data in the vehicle key
Information on the service notifications is con-
tinuously stored in the vehicle key. An author-
ized service center can read this data out and
suggest a maintenance scope for the vehicle.
Therefore, hand the service advisor the vehicle
key with which the vehicle was driven most
recently.
BMW maintenance system
The maintenance system provides service no-
tifications and thereby provides support in
maintaining road safety and the operational
reliability of the vehicle.
Stationary periods
Stationary periods during which the vehicle
battery was disconnected are taken into ac-
count.
In some cases, scopes and intervals of the
maintenance system may vary according to
the country version. Replacement work, spare
parts, fuels and lubricants, and wear materials
are calculated separately. Further information
is available from an authorized service center
or another qualified service center or repair
shop.
Have any time-dependent maintenance meas-
ures, e.g., replacing operating equipment, per-
formed by an authorized service center or an-
other qualified service center or repair shop.
Maintenance Booklet for US
Models
Condition Based Service
Please consult your Maintenance Booklet for
additional information on the performance of
service and maintenance work.
Principle
Condition Based Service determines the main-
tenance recommendation using sensors and
special algorithms that take into account the
operating conditions of the vehicle.
The manufacturer of the vehicle recommends
that maintenance and repair be performed by
an authorized service center or another quali-
fied service center or repair shop. Records of
regular maintenance and repair work should
be retained.
The system makes it possible to adapt the
maintenance measures to your user profile.
350
Online Edition for Part no. 01405B381F1 - II/24
Maintenance
MOBILITY
Position
Diagnostic socket
General information
Connecting devices to the on-board diagnos-
tics will trigger the alarm system once the vehi-
cle is locked.
Remove devices connected to the diagnostic
socket before locking the vehicle.
Additional information:
Indicator/warning lights, refer to page 155.
There is a diagnostic socket on the driver’s
side for reading out vehicle data.
Safety information
Exhaust emissions
NOTICE
▷
The warning light illuminates:
The socket for Onboard Diagnosis is an in-
tricate component intended to be used in
conjunction with specialized equipment to
check the vehicle’s primary emissions sys-
tem. Improper use of the socket for Onboard
Diagnosis, or contact with the socket for On-
board Diagnosis for other than its intended
purpose, can cause vehicle malfunctions and
creates risks of personal and property dam-
age. As such, it is strongly recommended that
access to the diagnostic socket be limited to
an authorized service center or another quali-
fied service center or repair shop, or other
persons who have specialized training and
equipment and who are able to use the diag-
nostic socket correctly.
Worsening exhaust emissions, e.g.,
due to an incorrectly fitted fuel cap.
Have the vehicle checked as soon
as possible.
▷
The warning light flashes under certain cir-
cumstances:
This indicates that there is excessive misfir-
ing in the engine.
Reduce the vehicle speed and have the ve-
hicle checked immediately; otherwise, se-
rious engine misfiring within a brief pe-
riod can seriously damage emission control
components, in particular the catalytic con-
verter.
Have the vehicle checked by an authorized
service center or another qualified service cen-
ter or repair shop.
351
Online Edition for Part no. 01405B381F1 - II/24
Replacing components
MOBILITY
Replacing components
Vehicle features and options
NOTICE
Folded-out wipers can be jammed when the
hood is opened. There is a risk of damage to
property. Make sure that the wipers with the
wiper blades mounted are folded down onto
the windshield before opening the hood.
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
Replacing the wiper blades
1. To change the wiper blades, bring wipers
into fold-out position.
Fold-out position of the wipers, refer to
page 143.
Onboard vehicle tool kit
2. Lift the wiper off of the windshield and hold.
The onboard vehicle tool kit is located in the
left storage compartment of the cargo area.
3. Press the button, arrow 1, and pull out the
wiper blade, arrow 2.
Wiper blades
Safety information
NOTICE
The window may sustain damage if the wiper
falls onto it without the wiper blade installed.
There is a risk of damage to property. Hold
the wiper firmly when changing the wiper
blade. Do not fold in or switch on the wiper
without a wiper blade installed.
4. Insert the new wiper blade and press it on
until it you hear it snap into the holder.
5. Fold in the wipers.
352
Online Edition for Part no. 01405B381F1 - II/24
Replacing components
MOBILITY
Lights and bulbs
Vehicle battery
General information
Lights and bulbs make an essential contribu-
tion to driving safety.
General information
The battery is maintenance-free.
More information on the battery can be re-
quested from an authorized service center or
another qualified service center or repair shop.
All headlights and lights are made using LED
or laser technology.
In the event of a malfunction, the vehicle man-
ufacturer recommends having an authorized
service center or another qualified service cen-
ter or repair shop perform any necessary work.
Safety information
DANGER
Contact with live components can lead to an
electric shock. There is a risk of injury or dan-
ger to life. Do not touch any components that
are under voltage.
Safety information
Warning
Focused laser light can irritate or perma-
nently damage the retina of the eye. There
is a risk of injury. The vehicle manufacturer
recommends having work on the lighting sys-
tem, including bulb replacement, performed
by an authorized service center or another
qualified service center or repair shop.
Warning
Vehicle batteries that are not recommended
can damage vehicle systems and impair ve-
hicle functions. There is a risk of accident,
injury, or property damage. Only use vehicle
batteries recommended by the vehicle manu-
facturer. For information on suitable vehicle
batteries, contact an authorized service cen-
ter or another qualified service center or re-
pair shop.
Warning
Intense brightness can irritate or damage the
retina of the eye. There is a risk of injury. Do
not look directly into the headlights or other
light sources. Do not remove the LED covers.
Registering the battery to the
vehicle
Headlight glass
The vehicle manufacturer recommends hav-
ing an authorized service center or another
qualified service center or repair shop register
the vehicle battery to the vehicle after the bat-
tery has been changed. Once the battery has
been registered again, all comfort features will
be available without limitation and any Check
Control messages displayed which relate to
comfort features will disappear.
The inside of the headlight glass can fog up
in cool or humid weather. When driving with
the lights switched on, the condensation evap-
orates after a short time. The headlight glass
does not need to be changed.
If, despite driving with the headlights switched
on, moisture such as water droplets increas-
ingly forms in the light, have the headlights
checked.
353
Online Edition for Part no. 01405B381F1 - II/24
Replacing components
MOBILITY
▷
With Memory function: store the positions
again.
Charging the battery
General information
Make sure that the battery is always suffi-
ciently charged to guarantee that the battery
remains usable for its full service life.
▷
▷
Time: update.
Date: update.
Disposing of old batteries
A discharged battery is indicated by a
red indicator light.
Have old batteries disposed of by an
authorized service center or another
qualified service center or repair shop,
or take them to a collection point.
Charge the battery when acceleration is insuffi-
cient.
Maintain the filled battery in an upright position
for transport and storage. Secure the battery
so that it does not tip over during transport.
The following circumstances can have a nega-
tive effect on the performance of the battery:
▷
▷
Frequent short-distance drives.
Stationary periods of more than one month.
Fuses
Safety information
General information
The fuses are located at different places in the
vehicle.
Warning
Battery chargers that charge the vehicle bat-
tery via sockets or cigarette lighters in the ve-
hicle may overload or damage the 12 V elec-
trical system. There is a risk of injury or risk
of damage to property. Only connect battery
chargers for the vehicle battery to the jump-
start terminals in the engine compartment.
Safety information
Warning
Incorrect and repaired fuses can overload
electrical lines and components. There is a
risk of fire. Never attempt to repair a blown
fuse. Do not replace a nonworking fuse with a
substitute of another color or amperage rat-
ing.
Charging the battery
Charge the battery only when the engine is off
and via the jump-start terminals in the engine
compartment.
Additional information:
In the car's interior
The fuses are located in the car's interior in the
front passenger footwell behind a cover.
Jump-start terminals, refer to page 360.
Power interruption
After a power interruption, some equipment
needs to be newly initialized or individual set-
tings updated, for example:
354
Online Edition for Part no. 01405B381F1 - II/24
Replacing components
MOBILITY
Loosen fasteners, arrows, and open cover.
The fuse box is located on the front right.
In the cargo area
The fuses are located in the cargo area on the
right side behind a cover.
Remove the cover.
The fuse box may be located behind the sound
insulation.
Information on the fuse layout as well as the
positions of other fuse boxes is available on
the Internet:
Additional fuse boxes
Additional fuse boxes are located in the vehi-
cle. In the event of a malfunction, contact an
authorized service center or another qualified
service center or repair shop.
Replacing fuses
The vehicle manufacturer recommends having
the fuses replaced by an authorized service
center or another qualified service center or
repair shop.
355
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
Breakdown Assistance
Vehicle features and options Warning triangle
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
The warning triangle is located in the cargo
area.
Hazard warning flashers
Release the hook and loop fastener to remove
it.
First-aid kit
General information
Depending on the vehicle equipment and na-
tional-market version, the vehicle is equipped
with a first-aid kit.
The button is located in the center console.
Some of the articles have a limited service life.
The red light in the button flashes when the
hazard warning flashers are activated.
Check the expiration dates of the contents reg-
ularly and replace any expired items promptly.
Storage
Storage for the first-aid kit is provided in the
left storage compartment of the cargo area.
356
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
Supplementary text messages, refer to
page 155.
BMW Assistance
▷
▷
Via a call with a mobile phone.
Via the BMW app.
Principle
In the event of a breakdown, accident or if you
have any questions about the vehicle, BMW
Assist can be used to contact BMW Group's
customer support.
Functional requirements
▷
Active ConnectedDrive contract, equipment
with intelligent emergency call or BMW
ConnectedDrive services.
General information
The offering depends on the vehicle equip-
ment and the national-market version.
▷
▷
Cellular network reception.
Standby state is switched on.
For more information on this service, the vehi-
cle manufacturer recommends contacting an
authorized service center or the hotline/cus-
tomer support.
Starting BMW Roadside Assistance
manually
If the vehicle is equipped with Teleservices,
support is first offered through Teleservice Di-
agnosis and, where applicable, then through
Teleservice Help.
Starting services
1. "APPS"
2. "Installed apps"
3. "BMW Assist"
4. "Call BMW Assist"
1. "APPS"
2. "Installed apps"
3. "BMW Assist"
5. Follow the instructions on the control dis-
play.
4. "BMW Roadside Assistance"
Follow the displays on the control display.
A voice connection is established.
A voice connection to customer support is be-
ing established.
Teleservice Diagnosis
Teleservice Diagnosis enables the wireless
transmission of detailed vehicle data that is
important for vehicle diagnosis. This data is
transmitted automatically. It may be necessary
to approve this on the control display.
BMW Roadside Assistance
Principle
BMW Group Roadside Assistance can be con-
tacted if assistance is needed in the event of a
breakdown.
Teleservice Help
Depending on the country, Teleservice Help
enables an in-depth diagnosis of the vehicle by
BMW Roadside Assistance via wireless trans-
mission.
General information
In the event of a breakdown, data on the ve-
hicle's condition is transmitted to the BMW
Roadside Assistance.
There are various ways of contacting BMW
Roadside Assistance.
▷
Via a Check Control message.
357
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
You can launch Teleservice Help by requesting
it through BMW Roadside Assistance.
stored Check Control messages for a certain
length of time.
Additional information:
1. Park the vehicle in a safe place.
2. Set the parking brake.
Check Control, refer to page 154.
3. Control display is switched on.
4. Confirm Teleservice Help.
Starting BMW Accident Assistance
manually
BMW Accident Assistance can also be con-
tacted independently of the automatic accident
detection function.
BMW Accident Assistance
1. "APPS"
Principle
2. "Installed apps"
3. "BMW Assist"
BMW Group Accident Assistance can be con-
tacted if assistance is needed in the event of
an accident.
4. "BMW Accident Assistance"
Follow the displays on the control display.
A voice connection is established.
General information
If the vehicle sensors detect a minor to moder-
ately severe accident, which did not deploy any
airbags, a Check Control message appears on
the instrument cluster. In addition, a text mes-
sage appears on the control display.
Emergency Call
Intelligent emergency call
When BMW Accident Assistance is triggered,
data on the vehicle's condition is sent to BMW.
Principle
In case of an emergency, an emergency call
can be triggered automatically by the system
or manually.
Functional requirements
▷
Active ConnectedDrive contract, equipment
with intelligent emergency call or BMW
ConnectedDrive services.
General information
Depending on the vehicle equipment and na-
tional-market version, the vehicle is equipped
with an Assist system.
▷
▷
Cellular network reception.
Standby state is switched on.
Starting BMW Accident Assistance
Only press the SOS button in an emergency.
The Intelligent Assist system establishes a
connection with the BMW Response Center.
If an accident is detected automatically
A text message relating to BMW Accident As-
sistance appears on the control display.
For technical reasons, the emergency call can-
not be guaranteed under unfavorable condi-
tions.
The connection can be established directly:
"Contact accident assistance"
The Check Control message for BMW Accident
Assistance can also be called up from the
358
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
If the situation allows, wait in the vehicle
until the voice connection has been estab-
lished.
Overview
▷
The LED flashes green when a connection
to the BMW Response Center has been es-
tablished.
The BMW Response Center then makes
contact with the occupants of the vehicle
and initiates further steps to help.
Even if you are unable to respond, the
BMW Response Center can take further
steps to help you under certain circumstan-
ces.
SOS button.
For this purpose, data that serves to deter-
mine the necessary rescue measures, for
instance the current position of the vehicle
when it can be determined, is transmitted
to the BMW Response Center.
Functional requirements
▷
▷
▷
Standby state is switched on.
The Assist system is functional.
If the vehicle is equipped with intelligent
emergency call: the integrated SIM card in
the vehicle has been activated.
Even if the BMW Response Center is no
longer heard through the loudspeakers, the
BMW Response Center may still be able to
hear the occupants of the vehicle.
Automatic triggering
When certain prerequisites are met, for in-
stance if the airbags deploy, an emergency call
is automatically initiated immediately after an
accident of corresponding severity. Automatic
Collision Notification is not affected by press-
ing the SOS button.
The BMW Response Center ends the emer-
gency call.
Malfunction
The function of the emergency call may be im-
paired.
The LED in the area of the SOS button flashes
for approximately 30 seconds. A Check Control
message is displayed.
Manual triggering
1. Tap the cover flap.
2. Press and hold the SOS button until the
LED in the area of the button illuminates
green.
An emergency call may be disrupted in the fol-
lowing circumstances, among others:
▷
▷
Extended vehicle idle times.
▷
The LED is illuminated green when an
emergency call has been initiated.
Intense sunlight on vehicle roof.
Have the vehicle checked by an authorized
service center or another qualified service cen-
ter or repair shop.
If a cancel prompt appears on the control
display, the emergency call can be aborted.
359
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
Jump-start terminals
The jump-start terminal in the engine compart-
ment acts as the positive battery terminal.
Jump-starting
General information
A special connection on the body in the engine
compartment acts as the negative battery ter-
minal.
If the battery is discharged, the engine can
be started using the battery of another vehicle
and two jumper cables. Only use jumper ca-
bles with fully insulated clamp handles.
Additional information:
Overview of engine compartment, refer to
page 340.
Safety information
Open the cover of the positive battery terminal.
DANGER
Connecting the cables
Before you begin, switch off all unnecessary
electronic systems/components such as the
radio on the assisting and receiving vehicles.
Contact with live components can lead to an
electric shock. There is a risk of injury or dan-
ger to life. Do not touch any components that
are under voltage.
1. Open the lid of the jump-start terminal.
2. Attach one terminal clamp of the positive
jumper cable to the positive battery termi-
nal, or to the corresponding jump-start ter-
minal of the vehicle providing assistance.
Warning
If the jumper cables are connected in the
incorrect order, spark formation may occur.
There is a risk of injury. Pay attention to the
correct order during connection.
3. Attach the terminal clamp on the other end
of the cable to the positive battery terminal,
or to the corresponding jump-start terminal
of the vehicle to be started.
Warning
4. Attach one terminal clamp of the negative
jumper cable to the negative battery termi-
nal, or to the corresponding engine or body
ground of assisting vehicle.
In the case of body contact between the two
vehicles, a short circuit can occur while jump-
starting. There is a risk of injury or risk of
damage to property. Make sure that no body
contact occurs.
5. Attach the second terminal clamp to the
negative battery terminal, or to the corre-
sponding engine or body ground of the ve-
hicle to be started.
Preparation
1. Check whether the battery of the other ve-
hicle has a voltage of 12 volts. The voltage
information can be found on the battery.
Starting the engine
Never use spray fluids to start the engine.
1. Start the engine of the assisting vehicle and
let it run for several minutes at an increased
idle speed.
2. Switch off the engine of the assisting vehi-
cle.
3. Switch off any electrical components in
both vehicles.
2. Start the engine of the vehicle that is to be
started in the usual way.
360
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
If the first attempt to start the engine is not
Pushing the vehicle
successful, wait a few minutes before mak-
ing another attempt in order to allow the
discharged battery to recharge.
To remove a broken-down vehicle from the
hazard area, it can be pushed for distances
of approx. 328 ft/100 m at a speed of max.
6 mph/10 km/h.
3. Let both engines run for several minutes.
4. Disconnect the jumper cables in the reverse
order.
Additional information:
Rolling or pushing the vehicle, refer to
page 146.
Check the battery and recharge, if needed.
Tow truck
Tow-starting and towing
Safety information
Warning
When towing with Intelligent Safety systems
enabled or Cruise Control switched on, in-
dividual functions may not work correctly.
There is a risk of accident, injury, or property
damage. Switch off all Intelligent Safety sys-
tems and Cruise Control before towing.
Have vehicle transported on a loading platform
or use a tow dolly.
When using a tow dolly, make sure that
none of the wheels touch the ground. This
method should be used for distances of max.
124 miles/200 km. Follow the instructions, as
well as specified loads and speeds, given by
the tow dolly manufacturer.
Steptronic transmission:
transporting the vehicle
General information
The vehicle must be transported on a loading
platform or tow dolly.
Towing other vehicles
Safety information
General information
Switch on the hazard warning system, de-
pending on local regulations.
Warning
If the electrical system has failed, clearly iden-
tify the vehicle being towed by placing a sign or
a warning triangle in the rear window.
The vehicle can become damaged when lift-
ing and securing it.
There is a risk of injury or risk of damage to
property.
▷
▷
Lift the vehicle using suitable means.
Do not lift or secure the vehicle by its
towing eye, body parts, or suspension
parts.
361
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
▷
▷
Do not exceed a towing distance of
3 miles/5 km.
Safety information
When driving off to tow the vehicle, make
sure that the tow rope is taut.
Warning
If the approved gross vehicle weight of the
towing vehicle is lighter than the vehicle to be
towed, the towing eye can tear off or it will
not be possible to control vehicle handling.
There is a risk of accident, injury, or property
damage. Make sure that the gross vehicle
weight of the towing vehicle is heavier than
the vehicle to be towed.
Towing eye
Principle
The towing eye is a device that can be
screwed onto the vehicle in order to, e.g., se-
cure tow cables or tow rods.
General information
NOTICE
If the tow bar or tow rope is attached incor-
rectly, damage to other vehicle parts can oc-
cur. There is a risk of damage to property.
Correctly attach the tow bar or tow rope to
the towing eye.
Tow bar
The towing eyes used should be on the same
side on both vehicles.
The screw-in towing eye should always be car-
ried in the vehicle.
If it is impossible to avoid mounting the tow
bar at an inclination, note the following:
The towing eye can be screwed in at the front
or rear of the vehicle.
▷
▷
Free movement is limited when cornering.
Safety information
The tow bar will generate lateral forces if it
is secured with an inclination.
NOTICE
Tow rope
If the towing eye is not used as intended,
there may be damage to the vehicle or to
the towing eye. There is a risk of damage
to property. Follow the notes on using the
towing eye.
Observe the following notes when using the
tow rope:
▷
▷
▷
▷
Use nylon ropes or straps, which will enable
the vehicle to be towed without jerking.
Make sure the tow rope is not twisted when
fastening.
Storage
Check the attachment of the towing eye
and tow rope in regular intervals.
Depending on vehicle equipment, the towing
eye is stored as follows:
Do not exceed a towing speed of
30 mph/50 km/h.
362
Online Edition for Part no. 01405B381F1 - II/24
Breakdown Assistance
MOBILITY
▷
▷
▷
Under the cargo area floor, in a bag if nec-
essary.
Have the cause of starting issues corrected by
an authorized service center or another quali-
fied service center or repair shop.
On the left or right side of the trunk, possi-
bly in a bag.
Additional information:
Behind a side trim panel in the trunk, possi-
bly in a bag.
Jump-starting, refer to page 360.
Using the towing eye
When using the towing eye, note the following:
▷
▷
Use only the towing eye provided with the
vehicle.
Turn the towing eye at least 5 turns clock-
wise and screw it in as far as it will go. If
necessary, tighten with a suitable object.
▷
▷
▷
After use, unscrew the towing eye counter-
clockwise.
Use the towing eye for towing on paved
roads only.
Avoid lateral loading of the towing eye, for
instance do not lift the vehicle by the towing
eye.
▷
Check the attachment of the towing eye in
regular intervals.
Towing eye thread
Press on the mark on the edge of the cover to
push it out.
Tow-starting
Do not tow-start the vehicle.
Start the engine by jump-starting, if possible.
363
Online Edition for Part no. 01405B381F1 - II/24
Vehicle care
MOBILITY
Vehicle care
Steam-jet cleaner and high
pressure cleaner
Vehicle features and options
This chapter describes all standard, country-
specific, and optional equipment offered with
the series. It also describes features and func-
tions that are not necessarily available in the
vehicle, e.g., due to the selected options or
country versions. This also applies to safety
functions and systems. When using these
functions and systems, the applicable laws
and regulations must be observed.
Safety information
NOTICE
When cleaning with high pressure cleaners,
components can be damaged due to the
pressure or temperatures being too high.
There is a risk of damage to property. Main-
tain sufficient distance and do not spray too
long continuously. Follow the operating in-
structions for the high pressure cleaners.
Washing the vehicle
General information
Regularly remove foreign objects such as
leaves in the area below the windshield when
the hood is raised.
Distances and temperature
▷
Maximum temperature: 140 ℉/60 ℃.
▷
Minimum distance from sensors, cameras,
seals and lights: 12 inches/30 cm.
Wash the vehicle frequently, particularly in win-
ter. Intense contamination and road salt can
damage the vehicle.
Automatic car washes or car
washes
Safety information
Safety information
NOTICE
NOTICE
When washing with an open fuel filler flap,
damage may occur. There is a risk of dam-
age to property. Close the fuel filler flap be-
fore washing. Clean dirt behind the fuel filler
flap with a cloth.
Using a car wash with high pressure washers
may result in water penetration of window
areas. There is a risk of damage to property.
Do not drive into high-pressure car wash sys-
tems.
NOTICE
Improper use of automatic car washes can
cause damage to the vehicle. There is a risk
of damage to property. Follow the following
instructions:
364
Online Edition for Part no. 01405B381F1 - II/24
Vehicle care
MOBILITY
▷
Give preference to cloth car washes or
those that use soft brushes in order to
avoid paint damage.
Turn on drive-ready state.
Additional information:
Drive-ready state, refer to page 41.
▷
▷
Note the permissible vehicle dimensions
for the car wash.
Lights
Do not drive through a car wash with
guide rails higher than 4 in/10 cm to
avoid damage to the body.
Do not rub wet lights dry and do not use
abrasive or acidic cleaning agents or cleaning
agents containing alcohol.
▷
▷
▷
Observe the tire width of the guide rail to
avoid damage to tires and rims.
Soak areas that have been dirtied, for instance
from insects, with auto shampoo and wash off
with water.
Fold in exterior mirrors to avoid damage
to the exterior mirrors.
Thaw ice with de-icing spray; do not use an ice
scraper.
Deactivate the wiper and, if necessary,
rain sensor to avoid damage to the win-
dow wiper system.
After washing the vehicle
▷
Take off all removable attachments, e.g.,
antennas.
After washing the vehicle, apply the brakes
briefly to dry them. Otherwise, their braking
effect may be reduced. The heat generated
while braking dries brake disks and brake pads
and protects them against corrosion.
Driving into a car wash with a
Steptronic transmission
Completely remove all residues on the win-
dows to minimize loss of visibility due to
smearing and to reduce wiper noises and
wiper blade wear.
NOTICE
Selector lever position P is automatically en-
gaged when standby state is switched off.
The wheels are blocked. There is a risk
of damage to property. Do not switch off
standby if the vehicle is meant to coast, e.g.,
in a car wash.
Vehicle care
Vehicle care products
In a car wash, the vehicle must be able to roll
freely.
General information
BMW recommends using vehicle care and
cleaning agents from BMW. Suitable vehicle
care products are available from an authorized
service center or another qualified service cen-
ter or repair shop.
Some car washes do not permit persons in the
vehicle. The vehicle cannot be locked from the
outside when in selector lever position N. A
signal sounds when an attempt is made to lock
the vehicle.
Additional information:
Rolling or pushing the vehicle, refer to
page 146.
Driving out of a car wash
Ensure that the vehicle key is in the car.
365
Online Edition for Part no. 01405B381F1 - II/24
Vehicle care
MOBILITY
Clean light-colored leather more frequently be-
cause contamination on such surfaces is sub-
stantially more visible.
Safety information
Warning
Use leather care products; otherwise, dirt and
grease will gradually break down the protective
coating of the leather surface.
Cleaning agents can contain substances that
are dangerous and harmful to your health.
There is a risk of injury and risk of damage to
property. When cleaning the interior, open the
doors or windows. Only use cleaning agents
that are intended for cleaning the respective
component. Follow the instructions on the
packaging.
Synthetic leather care
Clean synthetic leather regularly with a damp
microfiber cloth or vacuum cleaner.
Otherwise, dust and road grime particles will
rub into pores and folds, causing significant
abrasion and premature degradation of the
surface.
Vehicle paintwork
In case of major soiling, use a moist soft
sponge or microfiber cloth with suitable interior
cleaners.
General information
Regular vehicle care contributes to driving
safety and value retention. Environmental in-
fluences in areas with elevated air pollution or
natural contaminants such as tree resin or pol-
len can affect the vehicle paintwork. Align the
frequency and extent of vehicle care according
to the degree of soiling.
Immediately remove aggressive substances
such as sunscreen to prevent the synthetic
leather from being altered or discolored.
Fabric care
Corrosive substances such as spilled fuel, oil,
grease or bird droppings must be removed
immediately to prevent the finish from being
altered or discolored.
General information
In case of major contaminations such as bev-
erage stains, use a moist soft sponge or micro-
fiber cloth with a suitable interior cleaners.
Immediately remove aggressive substances,
e.g., sunscreen, to prevent alterations or dis-
colorations of the fabric.
Matte paintwork
Only use cleaning and care products suitable
for vehicles with matte paintwork.
Safety information
Leather care
Particles of dust and road grime rub into pores
and folds, causing heavy abrasion and prema-
ture degradation of the leather surface.
NOTICE
Open hook and loop fasteners on articles of
clothing can damage the seat covers and
other cloth upholstery in the vehicle. There is
a risk of damage to property. Ensure that any
Velcro® fasteners are closed.
Remove dust from the leather regularly, using
a cloth or vacuum cleaner.
To guard against discoloration such as from
clothing, clean leather and provide leather care
roughly every two months.
Upholstery material care
Vacuum regularly with a vacuum cleaner.
366
Online Edition for Part no. 01405B381F1 - II/24
Vehicle care
MOBILITY
Clean extensively down to the seams. Avoid
rubbing the material vigorously.
Wiper blades
The wiper blades are cleaned by using the
window washer system.
Textile care
Use a microfiber cloth for cleaning minor con-
tamination.
Avoid cleaning the wiper blades manually, as
this may reduce wiper performance.
Dampen the cloth with water.
Caring for special components
Light-alloy wheels
When cleaning the vehicle, use only neutral rim
cleaners having a pH value from 5 to 9. Do not
use abrasive cleaning agents or steam clean-
ers above 140 ℉/60 ℃. Follow the manufac-
turer's instructions.
Fine wood parts
Clean the fine wood veneer and fine wood
components solely with a moist rag. Then dry
with a soft cloth.
Kenaf
Only treat parts made of Kenaf fibers using
suitable care products.
Plastic components
Corrosive, acidic, or alkaline cleaning agents
can damage the surface of the rims and the
protective layer of adjacent components, e.g.,
the brakes.
NOTICE
Solvent cleaners that contain alcohol or sol-
vents such as lacquer thinners, cold cleaning
agents, fuel and such, can damage plastic
parts. There is a risk of damage to property.
Clean with a microfiber cloth. Dampen the
cloth lightly with water, if needed.
After cleaning, apply the brakes briefly to dry
them. The heat generated while braking dries
brake disks and brake pads and protects them
against corrosion.
Chrome surfaces
Carefully clean Chrome surfaces, especially in
case of exposure to road salt, with plenty of
water and added auto shampoo as needed.
Do not soak the headliner.
Seat belts
Warning
Rubber components
Chemical solvent cleaners can destroy the
fabric of the seat belts and lead to seat belts
no longer having their protective effect. There
is a risk of injury or danger to life. Use only a
mild soap solution for cleaning the seat belts.
Environmental influences can cause surface
contamination of rubber parts and a loss of
gloss. Use only water and suitable cleaning
agents for cleaning.
Treat especially worn rubber parts with rubber
care products at regular intervals. When clean-
ing rubber seals, do not use any silicon-con-
taining vehicle care products in order to avoid
damage or noises.
Dirty belt straps impede the reeling action and
thus should be avoided for safety reasons.
Use only a mild soap solution for cleaning the
installed belt straps.
Seat belts should only be allowed to retract if
they are dry.
367
Online Edition for Part no. 01405B381F1 - II/24
Vehicle care
MOBILITY
▷
▷
▷
Avoid pressure that is too high and do
not use any scratching materials.
Carpets and floor mats
Use a dry, clean antistatic microfiber
cloth for cleaning displays.
Warning
Objects in the driver's footwell can limit the
pedal travel or block a depressed pedal.
There is a risk of accident. Stow objects in the
vehicle such that they are secured and can-
not enter into the driver's footwell. Use floor
mats that are suitable for the vehicle and
can be safely attached to the floor. Do not
use loose floor mats and do not layer several
floor mats. Make sure that there is sufficient
clearance for the pedals. Ensure that the floor
mats are securely fastened again after they
were removed, for instance for cleaning.
Clean the operating elements and, de-
pending on vehicle equipment, the pro-
tective glass of the Head-up display with
a damp microfiber cloth and standard
household dish soap.
Taking the vehicle out of service
When the vehicle is shut down for longer
than three months, special measures must
be taken. For more information, contact an
authorized service center or another qualified
service center or repair shop.
The floor mats can be removed from the inte-
rior for cleaning.
If the floor carpets are very contaminated,
clean with a microfiber cloth and water or a
textile cleaner. To prevent matting of the car-
pet, rub back and forth in the driving direction
only.
Sensors and camera lenses
To clean sensors and camera lenses, use a
cloth moistened with a small amount of glass
detergent.
Displays, operating elements and
protective glass of the Head-
up display
NOTICE
Surfaces can be damaged by improper
cleaning, e.g., by using chemical cleaners, or
from moisture or liquid of any kind. Physical
damage to the material is possible.
368
Online Edition for Part no. 01405B381F1 - II/24
Vehicle care
MOBILITY
369
Online Edition for Part no. 01405B381F1 - II/24
