Deutsch
EnglishStarting and driving -> HomeLink for your Volvo XC60 2017-2026
STARTING AND DRIVING
HomeLink® is delivered integrated in the rear-
view mirror. The HomeLink® panel consists of
three programmable buttons and an indicator
light in the mirror.
HomeLink®*23
||
WARNING
HomeLink®24 is a programmable remote con-
trol, integrated in the vehicle electrical sys-
tem, that can control up to three different
devices (e.g. garage door opener, alarm sys-
tem, outdoor and indoor lighting) and thereby
replace the remote controls for these.
No person or object should be behind the
tow truck when the vehicle is lifted onto
the bed of the truck.
For more information about HomeLink®,
1-800-355-3515.
The towing eyelet is only intended for tow-
ing on roads, and must not be used to pull
vehicles from ditches or any similar pur-
pose involving severe strain. Call a tow
truck for professional assistance.
Save the original remote controls for future
programming (e.g. for use in another vehicle).
It is also advisable to delete the button pro-
gramming if the vehicle is sold.
General
Related information
•
•
•
Note that the vehicle must always be
towed with the wheels rolling forward.
Related information
Attaching and removing the towing eyelet
(p. 439)
•
The illustration is generic – the design may vary.
Button 1
Button 2
Button 3
Indicator light
23
24
Certain markets only.
HomeLink and the HomeLink house symbol are registered trademarks of Gentex Corporation.
442
* Option/accessory.
STARTING AND DRIVING
Programming HomeLink®*25
Follow these instructions to program
HomeLink®, reset all programming, or pro-
gram individual buttons.
1. Point the remote control at the
HomeLink® button to be programmed and
hold it about 2-8 cm (1-3 inches) from the
button. Do not obstruct the HomeLink®
indicator light.
3. Do not release the buttons until the indica-
tor light has stopped flashing slowly
(about once a second) and either flashes
quickly (about 10 times a second) or
glows steadily.
> If the indicator light glows steadily:
Indication that programming is com-
plete. Press the programmed button
twice to activate.
Note: Some remote controls are more
effective at programming HomeLink® from
a distance of about 15-20 cm (6-12
inches). Keep this in mind if you experi-
ence any programming difficulties.
In some vehicles, the ignition must be on
or in the "accessory position" before
HomeLink® can be programmed or used. It
can be a good idea to put new batteries in
the remote control being replaced by
HomeLink® for faster programming and
better radio signal transmission. The
HomeLink® buttons should be reset before
programming.
If the indicator light flashes quickly:
The device being programmed with
HomeLink® may have a security func-
tion that requires an extra step. Try
pressing the programmed button twice
to see whether the programming
works. Otherwise, continue with the
following steps.
2. Press and hold both the remote control
button and the HomeLink® button to be
programmed.
WARNING
While HomeLink® is being programmed,
the garage door or gate being programmed
may be activated. Make sure that no one is
near the door or gate during programming.
When programming a garage door opener,
it is advised to park outside of the garage.
25
Certain markets only.
}}
* Option/accessory. 443
STARTING AND DRIVING
||
1–800–355–3515.
Related information
•
•
•
Programming individual buttons
To program an individual HomeLink® button:
1. Press and hold the desired button for
about 20 seconds.
When the indicator light on HomeLink®
starts flashing slowly, it is possible to pro-
gram as usual.
2.
4. Locate the "training" button26 on the
receiver for the e.g. garage door opener. It
is usually located near the antenna bracket
on the receiver.
Note: If the button you are reprogram-
ming does not program with a new
device, it will return to the previously
saved programming.
5. Press and release the "training" button
once. Programming must be completed
within 30 seconds after pressing the but-
ton.
Resetting the HomeLink® buttons
It is only possible to reset all HomeLink® but-
tons at once. It is not possible to reset individ-
ual buttons. Individual buttons can only be
reprogrammed.
Press and release the HomeLink® button
to be programmed. Repeat the press/
hold/release sequence a second time. For
some receivers, the sequence may need to
be repeated a third time.
6.
–
Press and hold the outer buttons (1 and 3)
on HomeLink® for about 10 seconds.
> When the indicator light goes from a
steady glow to flashing, the buttons
have been reset and are ready for
reprogramming.
> Programming is now completed and
the garage door, gate, etc. should now
be activated when the programmed
button is pressed.
If you experience any difficulties programming,
please contact HomeLink® at:
26
The name and color of the button varies depending on the manufacturer.
444
* Option/accessory.
STARTING AND DRIVING
Using HomeLink®*27
Type approval for HomeLink®*28
WARNING
Once HomeLink® is programmed, it can be
used instead of the separate remote controls.
Press and hold the programming button. The
garage door, gate, alarm system, etc. will be
activated (this may take several seconds). If
the button is held down for more than 20 sec-
onds, reprogramming will begin. The indicator
light will glow steadily or flash when the but-
ton has been pressed. The original remote
controls may be used concurrently with
HomeLink® if desired.
•
•
If you use HomeLink® to open a garage
door or gate, be sure no one is near the
gate or door while it is in motion.
FCC (USA) and IC (Canada)
This device complies with FCC rules part 15
and Industry Canada RSS-210. Operation is
subject to the following two conditions: (1)
This device may not cause harmful interfer-
ence, and (2) This device must accept any
interference that may be received including
interference that may cause undesired opera-
tion.
Do not use HomeLink® with any
garage door opener that lacks safety
stop and reverse features as required
by US federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982). A
garage door that cannot detect an
object - signaling the door to stop and
reverse - does not meet current U.S.
federal safety standards. For more
information, contact HomeLink at:
WARNING
The transmitter has been tested and com-
plies with FCC and IC rules. Changes or
modifications not expressly approved by
the party responsible for compliance could
void the user's authority to operate the
device.29
When the ignition is switched off,
HomeLink® will be active for at least
7 minutes.
Related information
•
•
•
Type approval for EU
HomeLink® cannot be used if the vehicle is
locked and the alarm is armed* from the
outside.
Gentex Corporation hereby declares that
HomeLink® Model UAHL5 complies with the
Radio equipment directive 2014/53/EU.
Wavelengths within which the radio equip-
ment operates:
433.05MHz-434.79MHz <10mW E.R.P.
868.00MHz-868.60MHz <25mW E.R.P.
•
•
27
Certain markets only.
Certain markets only.
28
29
The term "IC:" before the certification/registration number only signifies that Industry Canada technical specifications were met.
}}
* Option/accessory. 445
STARTING AND DRIVING
||
868.70MHz-868.20MHz <25mW E.R.P.
869.40MHz-869.65MHz <25mW E.R.P.
869.70MHz-870.00MHz <25mW E.R.P.
•
•
•
Activating and deactivating the
Compass*
An integrated compass30 in the upper right
corner of the rearview mirror shows the
direction the vehicle is traveling.
compass*
An integrated compass31 in the upper right
corner of the rearview mirror shows the
direction the vehicle is traveling.
Certificate holder address: Gentex Corpora-
tion, 600 North Centennial Street, Zeeland MI
49464, USA
The compass is automatically activated when
the vehicle is started.
For further details, search for support informa-
To deactivate/activate the compass manually:
–
Use a paper clip or similar object to press
the button on the bottom of the mirror.
Related information
•
> If the compass is deactivated when the
vehicle is switched off, it will not be
activated the next time the vehicle is
started. The compass will then need to
be activated manually.
Rearview mirror with compass.
Related information
Eight different compass directions are shown
with the abbreviations: N (north), NE (north-
east), E (east), SE (southeast), S (south), SW
(southwest), W (west) and NW (northwest).
•
Calibrating the compass* (p. 447)
•
Related information
•
Calibrating the compass* (p. 447)
•
30
31
Rearview mirror with compass is available as an option only on certain markets and models.
Rearview mirror with compass is available as an option only on certain markets and models.
446
* Option/accessory.
