Deutsch
EnglishStarting and driving -> HomeLink? for your Volvo XC40 2018-2026
STARTING AND DRIVING
HomeLink® is supplied built-in to the interior
rearview mirror. The HomeLink® panel con-
sists of three programmable buttons and one
indicator lamp in the mirror glass.
HomeLink®*33
HomeLink®34 is a programmable remote con-
trol, integrated in the car's electrical system,
which can remotely control up to three differ-
ent devices (e.g. garage door opener, alarm
system, outdoor and indoor lighting) and
thereby replace the remote controls for them.
Note that the car must always be transpor-
ted with the wheels rolling forward.
For more information about HomeLink®, visit
Related information
Fitting and removing the towing eye
(p. 459)
•
00 8000 466 354 65 (or the toll number
+49 6838 907 277)35
.
General
Save the original remote controls for future
programming (e.g. when changing to another
car or for use in another vehicle).
The programming for the buttons should
be deleted when the car is sold.
Related information
•
•
•
The figure is schematic - the version may vary.
Button 1
Button 2
Button 3
Indicator lamp
33
34
35
Applies to certain markets.
HomeLink and the HomeLink house symbol are registered trademarks of Gentex Corporation.
Note that the toll-free number may not be available depending on operator.
* Option/accessory. 461
STARTING AND DRIVING
Programming HomeLink®*36
Follow these instructions to program
HomeLink®, reset all programming or repro-
gram individual buttons.
1. Aim the remote control towards the
HomeLink® button to be programmed and
hold it approx. 2-8 cm (approx. 1-3 inches)
from the button. Do not obstruct the indi-
cator lamp on HomeLink®.
3. Do not release the buttons until the indica-
tor lamp has switched from flashing
slowly (approx. once per second) to either
flashing quickly (approx. 10 times per sec-
ond) or illuminating with a constant glow.
> If the indicator lamp illuminates with
a constant glow: Indication that the
programming has finished. Press the
programmed button twice to activate.
Note: The ability of some remote controls
to program HomeLink® is improved at a
distance of approx. 15-20 cm (approx.
6-12 inches). Bear this in mind if problems
occur with the programming.
In certain vehicles the ignition must be
switched on or in "accessory position"
before HomeLink® can be programmed or
used. If possible, fit new batteries in the
remote control that shall be replaced by
HomeLink® for faster programming and
improved transmission of the radio signal.
The HomeLink® buttons should be reset
before programming.
If the indicator lamp flashes quickly:
The device to be programmed to
HomeLink® may have a security func-
tion that requires extra steps. Test by
pressing the programmed button twice
to see whether the programming is
working. Otherwise, continue with the
following steps.
2. Press and hold depressed both the button
on the remote control and the button to be
reprogrammed on HomeLink®.
WARNING
While programming HomeLink®, the
garage door or gate being programmed
may activate. For this reason, make sure
that nobody is in the vicinity of the door or
gate while programming is in progress. The
car should be outside the garage while a
garage door opener is being programmed.
36
Applies to certain markets.
462
* Option/accessory.
STARTING AND DRIVING
call 00 8000 466 354 65 (or the toll number
+49 6838 907 277)38
Related information
.
•
•
•
Reprogramming individual buttons
To reprogram an individual HomeLink® button,
proceed as follows:
1. Press the desired button and hold it
depressed for approx. 20 seconds.
Once the indicator lamp on HomeLink®
starts to flash slowly, programming can
continue as normal.
2.
4. Locate programming button37 on the
receiver for the garage door or similar. It is
normally located close to the antenna's
bracket on the receiver.
Note: If the button to be reprogrammed is
not programmed with a new unit, it will
resume the previously saved program-
ming.
5. Depress and release the receiver's pro-
gramming button once. The programming
must be completed within 30 seconds of
the button being depressed.
Resetting the HomeLink® buttons
It is only possible to reset all of the HomeLink®
buttons at the same time, not each button
individually. Individual buttons can only be
reprogrammed.
6. Press and release the button on
HomeLink® that you want to program.
Repeat the sequence of pressing/holding/
releasing a second time and, depending
on the receiver model, even a third time.
–
Press and hold depressed the outer but-
tons (1 and 3) on HomeLink® for approx.
10 seconds.
> Programming is now be complete and
the garage door, gate or similar should
now be activated when the pro-
> When the indicator lamp changes over
from a constant glow to starting to
flash, the buttons are reset and ready to
be reprogrammed.
grammed button is depressed.
In the event of programming problems, con-
tact HomeLink® at www.HomeLink.com, or
37
Button designation and colour varies between manufacturers.
Note that the toll-free number may not be available depending on operator.
38
* Option/accessory. 463
STARTING AND DRIVING
Using HomeLink®*39
Type approval for HomeLink®*40
WARNING
When HomeLink® is fully programmed it can
be used in place of the separate original
remote controls.
•
•
If HomeLink® is used to control a
garage door or gate, ensure that
nobody is near the door or gate while it
is in motion.
Do not use HomeLink® for any garage
door that does not have safety stop
and safety reverse.
Type approval for EU
Gentex Corporation hereby declares that
HomeLink® Model UAHL5 complies with the
Radio equipment directive 2014/53/EU.
Depress the programmed button. The garage
door, gate, alarm system or similar is activated
(may take a few seconds). If the button is
depressed for more than 20 seconds then the
reprogramming is started. The indicator lamp
illuminates or flashes when the button has
been depressed. Naturally the original remote
controls can still be used in parallel with
HomeLink® if required.
Wavelength within which the radio equipment
functions:
433.05MHz-434.79MHz <10mW E.R.P.
868.00MHz-868.60MHz <25mW E.R.P.
868.70MHz-868.20MHz <25mW E.R.P.
869.40MHz-869.65MHz <25mW E.R.P.
869.70MHz-870.00MHz <25mW E.R.P.
•
•
•
•
•
Related information
•
•
•
Certificate holder address: Gentex Corpora-
tion, 600 North Centennial Street, Zeeland MI
49464, USA
When the ignition has been switched off,
HomeLink® works for at least 7 minutes.
For more information, search support informa-
HomeLink® cannot be used if the car is
locked and the alarm is armed* from the
outside.
Related information
•
39
Applies to certain markets.
Applies to certain markets.
40
464
* Option/accessory.
STARTING AND DRIVING
Compass*
Activating and deactivating the
Calibrating the compass*
compass*
The upper right-hand corner of the rearview
mirror has an integrated display that shows
the compass direction41 in which the front of
the car is pointing.
The earth is divided into 15 magnetic zones.
The compass43 should be calibrated if the car
is moved between several magnetic zones.
The upper right-hand corner of the rearview
mirror has an integrated display that shows
the compass direction42 in which the front of
the car is pointing.
1. Stop the car in a large open area free from
steel structures and high-voltage power
lines.
The compass is activated automatically when
the car is started.
2. Start the car and switch off all electrical
equipment (air conditioning, wipers, etc.)
and ensure that all doors are closed.
To deactivate/activate the compass manually:
–
Depress the button on the underside of
the rearview mirror using e.g. a paper clip.
> If the compass is deactivated when the
car is switched off, it will not be acti-
vated the next time the car is started. In
this case, the compass needs to be
activated manually.
Calibration may fail or not start at all if
electrical equipment is not switched off.
3. Hold the button on the underside of the
rearview mirror depressed for
Rearview mirror with compass.
Related information
approx. 3 seconds (use a paper clip, for
example). The number for the current
magnetic zone is shown.
Eight different compass directions are shown
by their English abbreviations: N (north), NE
(north east), E (east), SE (south east), S
(south), SW (south west), W (west) and NW
(north west).
•
•
Related information
•
•
41
A rearview mirror with a compass is available as an option on certain markets and models only.
A rearview mirror with a compass is available as an option on certain markets and models only.
A rearview mirror with a compass is available as an option on certain markets and models only.
42
43
}}
* Option/accessory. 465
STARTING AND DRIVING
||
7. Cars with heated windscreen*: If the
character C is shown in the display when
the heated windscreen is activated, per-
form the calibration in accordance with
point 6 above with the heated windscreen
activated.
8. Repeat the above procedure as necessary.
Related information
•
•
Magnetic zones.
4. Press the button repeatedly until the
required magnetic zone (1–15) is shown.
See the map of magnetic zones for the
compass.
5. Wait until the display returns to showing
the character C, or hold the button on the
underside of the rearview mirror
depressed for approx. 6 seconds until the
character C is shown.
6. Drive slowly in a circle at a speed of no
more than 10 km/h (6 mph) until a com-
pass direction is shown in the display,
indicating that calibration is complete.
Then drive a further 2 circles to fine-tune
calibration.
466
* Option/accessory.
SOUND, MEDIA AND INTERNET
