Deutsch
EnglishEase of use and comfort -> Rear seats for your Peugeot 3008 2016-2023
Ease of use and comfort
Folding from the boot
► Put the backrest 3 in the upright position and
push it firmly to latch it home.
► Check that the red indicator is no longer
visible in the release grip 1.
► Ensure that the outer seat belts were not
trapped during the operation.
Please note: an incorrectly latched
backrest compromises the safety of
passengers in the event of sudden braking or
an accident.
The contents of the boot may be thrown
forward - risk of serious injury!
► Pull the backrest release lever 2 towards you.
The backrest 3 folds fully onto the cushion.
Second row seats
Repositioning the backrests
First check that the outer seat belts are
lying vertically flat alongside the backrest
latching rings.
A. Longitudinal adjustment
B. Seat backrest angle adjustment and folding
C. Folding the backrest from behind and
emergency exit for third row passengers
D. Access to third row seats
Seat adjustment
The three second row seats are independent
and of the same width. Their backrests can be
folded to adapt the boot load space.
50
Ease of use and comfort
Before and while performing the
operation on the seats, check that the
passengers, children in particular, keep their
hands and their feet far from the moving parts
of the seats (hinges, slides, etc.) - risk of
serious injury!
Longitudinal adjustment
► Lift control handle B1 and guide the backrest
backwards or forwards, raising yourself slightly
if needed.
► Release the handle and ensure the backrest
is properly locked on one of the positions offered.
Central seat
3
► Lift control strap B2 and guide the backrest
backwards or forwards, raising yourself slightly
if needed.
Folding from the outside
► Release the strap and ensure the backrest is
properly locked on one of the positions offered.
Flat floor
► Raise control bar A and slide the seat
forwards or backwards.
► Release the bar to lock the seat in position in
one of the notches.
Seat backrest angle adjustment
► Pull handle B1 or strap B2 until the backrest
is fully folded.
► Release the control.
► Gently push the backrest forwards so that
the backrest tilts until it is folded onto the seat
cushion.
Folding the backrests
► Check that the "aircraft" type tables of the
front seats are properly folded.
► Place the second row seats in the maximum
rear position.
Side seats
51
Ease of use and comfort
Folding from the boot
► Straighten the backrest until it locks.
Before unfolding the continuity panels,
check that the 2nd row seats are pulled as
far back as possible.
Before performing any operations on the
rear seats, to avoid damage to the seat
belts, check that the outer seat belts are
properly tensioned. The central seat belt must
be stored in the headlining.
Accessing third row seats
The third row seats are accessed via the second
row side seats.
Continuity panels
When loading, for example, or from the third row
seats:
► Pull strap C to unlock the desired seat and
give the backrest a slight push forwards.
Repositioning the seat
From the outside or from the third row seats:
► Check that the "aircraft" type tables of the
front seats are properly folded up.
► Pull paddle D and guide the backrest
forwards to tilt it and move the seat forwards.
To put the seat back in place:
► Straighten the backrest until the seat locks.
Whatever the initial position of the seat, it is
placed automatically a third of the way along
the longitudinal adjustment range in order to
preserve enough space for passengers in the
third row seats.
Each seat has a continuity panel at the bottom of
the backrest, which, once unfolded:
– allows for a continuous loading surface in the
boot, whatever the position of the seats,
– prevents objects from sliding beneath the 2nd
row seats.
The continuity panels are held against the
backrests with a magnetic fixing element.
These continuity panels are not designed
to support a weight greater than 30 kg.
► Place the continuity panels of the 2nd row
seats back up against the backrests.
52
Ease of use and comfort
If this system fails (paddle D), the third
row passengers can also get out after
having folded the backrest of the second row
seats using strap C.
Do not let children operate the seats
unsupervised.
► Pull one of the straps; the 3 sections of the
corresponding panel fold into concertina form.
When the 3rd row seats are straightened, these
folded concertina panels can be left upright or
flat behind the seats (freeing up the seat well as
a storage space).
3
Positioning the seats
These operations are carried out from the boot
sill.
Third row seats
When there is a seat at the back of the boot, the
removable support is fixed against the front wall
of its housing.
If the seat is removed from the back of the boot
for extra storage space, the removable support
must be installed on the two lugs on the central
wall.
The two third row seats are stored in a retracted
position in the bottom of the boot. Each one is
covered with rigid concertina panels, secured to
the vehicle.
Folding the concertina
panels
Do not let children operate the seats
unsupervised.
Each concertina panel can support a
maximum load of 100 kg with the third
row seats folded away.
With the third row seats removed and the
removable concertina panels supports
installed, the maximum load is limited to
50 kg.
► Remove the load space cover roller.
► Straighten the continuity panels of the 2nd row
seats.
► Fold back the concertina panel and straighten
it vertically.
► Pull the black strap E, located behind the
backrest.
The backrest tilts backwards bringing the seat
cushion with it; the seat locks in the open
position.
53
Ease of use and comfort
The load space cover roller can be stored behind
the backrests of the 3rd row seats.
► Reposition the concertina panels above the
retracted seats.
For more information on the Boot fittings, and
in particular the load space cover roller, refer to
the corresponding section.
Before doing anything to the 3rd row
seats, straighten the continuity panels of
the 2nd row seats.
Do not try to fold back a seat in the 3rd row
without having opened it until the backrest is
fully locked.
Do not leave anything on or underneath the
cushions of the 3rd row seats when they are
being folded.
Storing the seats
► Lift the yellow lever G, located on the right-
hand side, as far upwards as possible to unlock
the seat.
Do not guide strap F when storing the seat -
your fingers may get trapped!
Removing the seats
Removing the right-hand seat first is
recommended in order to facilitate access to the
left-hand seat unlocking control.
► Straighten the continuity panels of the 2nd row
seats.
► Place the head restraints in the low position.
► Check that the seat belts in the 3rd row are
properly stored along the side trims without
being folded or twisted.
► Pull red strap F, located at the bottom of the
backrest.
► While keeping the yellow lever held up as far
as possible, raise the rear part of the seat using
the red strap F.
The seat is unlocked.
► Push the backrest slightly forwards.
The backrest tilts and folds onto the cushion; the
folded seat is stored at the back of its storage
area.
The seat must be in the folded-away position.
These operations must be performed from the
boot sill.
► Fold back the concertina panel.
54
Ease of use and comfort
► While holding it by the sides at the plastic
covers, tilt the seat forwards.
► Simultaneously place both hooks located at
the front of the seat onto the coloured securing
lugs on the right and left at the bottom of the seat
well.
Seat modularity
3
Configuration examples
Check that the front hooks of the seat are
positioned correctly on the two lugs.
If they are not, you must remove the seat and
start the procedure again.
► Once the rear part of the seat has been
raised, take hold of each side of the seat
cushion, at the plastic covers, then bring the seat
towards you, keeping it at the same angle.
Repositioning the seats
These operations must be performed from the
boot sill.
7 seats
5 seats
Transport of
objects
As long as the seat is not in the correct
position, it must be held with both hands
by the sides, keeping it folded.
► Release the rear part of the seat which will
lock in place under its own weight.
The yellow lever G folds back automatically.
► Check in advance that the seat storage well
is empty and that the removable support is
properly secured against the front wall.
If the seat is not perfectly horizontal, do
not press on the backrest and do not try
to unfold it - risk of damaging the mechanism!
Take out the seat and start the operation
again.
6 seats
4 seats
By folding the second row seats and
retracting the third row seats, you obtain
55
