Deutsch
EnglishInstrument Panel -> Indicators for your Honda CR-V 2022-2025
Indicators
Parking Brake and
Brake System Indicator
(Red)
SPORT Mode Indicator P. 96
Low Fuel Indicator
P. 96
P. 97
*1
*1
P. 91
P. 92
*1
EV Indicator
P. 94
Anti-lock Brake System
(ABS) Indicator
*1
EV Mode Indicator
P. 94
Parking Brake and
Brake System Indicator
(Amber)
Road Departure
Mitigation (RDM)
Indicator
Supplemental Restraint
System Indicator
P. 97
P. 101
P. 97
P. 98
P. 98
P. 99
P. 100
*1
P. 103
P. 107
P. 102
Automatic Brake Hold
System Indicator
*1
*1
*1
*1
Auto High-Beam
Indicator
P. 93
P. 93
P. 93
P. 94
Collision Mitigation
Braking SystemTM
(CMBSTM) Indicator
Automatic Brake Hold
Indicator
Vehicle Stability AssistTM
(VSA®) System Indicator
Blind spot
information System
Indicator*
Low Oil Pressure
Indicator
Vehicle Stability AssistTM
(VSA®) OFF Indicator
Immobilizer System
Indicator
Security System Alarm
Indicator
Malfunction Indicator
Lamp
P. 101
P. 102
Electric Power Steering
(EPS) System Indicator
12-Volt Battery
Charging System
Indicator
*1
P. 95
Low Tire Pressure/TPMS
Indicator
Adaptive Cruise Control
(ACC) with Low Speed
Follow Indicator
(Amber)
Adaptive Cruise Control
(ACC) with Low Speed
Follow Indicator
(Green)
P. 105
P. 106
Shift Position Indicator
P. 95
P. 95
Turn Signal and Hazard
Warning Indicators
Deceleration Paddle
Selector Indicator
High Beam Indicator
Lights On Indicator
Fog Light Indicator*
P. 100
P. 101
P. 101
Transmission System
Indicator
P. 95
P. 93
P. 93
Lane Keeping Assist
System (LKAS)
Indicator (Amber)
Lane Keeping Assist
System (LKAS)
READY Indicator
*1
P. 106
P. 106
POWER SYSTEM
Indicator
System Message
Indicator
*1
P. 100
P. 102
Seat Belt Reminder
Indicator
P. 96
ECON Mode Indicator
Indicator (Green)
*1: When you set the power mode to ON, these indicators come on to indicate that system checks are being performed. They go off a few seconds later or after the power
system has started. If an indicator does not come on or turn off, there may be a malfunction in the corresponding system. To resolve the issue, follow the instructions in
the owner’s manual.
* Not available on all models
90
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
Comes on when the parking
brake is applied and goes off
when it is released.
Comes on when the brake fluid
level is low.
Comes on while driving - Make sure the
parking brake is released. Check the brake fluid level.
2 What to do when the indicator comes
on while driving P. 654
Comes on along with the Parking
Brake and Brake System Indicator
(Amber) - Immediately stop in a safe place.
Contact a dealer for repair. The brake pedal
becomes harder to operate. Depress the
pedal further than you normally do.
2 If the Brake System Indicator (Red)
Comes On or Blinks at the Same Time
When the Brake System Indicator
●
●
●
Comes on if there is a problem
with the brake system.
The beeper sounds and the
indicator comes on if you drive
with the parking brake applied.
Comes on for about 15 seconds
when you apply the electric
parking brake while the power
mode is in ACCESSORY or
VEHICLE OFF, then goes off.
Stays on for about 15 seconds
when you set the power mode to
VEHICLE OFF while the electric
parking brake is applied, then
goes off.
●
Parking Brake
and Brake
(Amber) Comes On P. 655
●
●
Comes on along with the ABS
indicator - Have your vehicle checked by a dealer.
2 If the Brake System Indicator (Red)
Comes On or Blinks P. 654
Blinks and the Parking Brake and
Brake System Indicator (Amber) comes
on at the same time - There is a problem
with the electric parking brake system. The
parking brake may not be set.
System Indicator
(Red)
(Red)
●
Avoid using the parking brake and have your
vehicle checked by a dealer immediately.
2 If the Brake System Indicator (Red)
Comes On or Blinks at the Same Time
When the Brake System Indicator
(Amber) Comes On P. 655
Continued
91
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
Comes on if there is a problem
with a system related to braking
other than the conventional brake
system.
Comes on if there is a problem
with the cooperative control with
regenerative braking, the electric
servo brake system, or the hill start
assist system.
Comes on while driving - Avoid high
speeds and sudden braking. Take the
vehicle to a dealer immediately.
●
Stays on constantly - Avoid using the
parking brake and have your vehicle
checked by a dealer immediately.
●
Comes on if there is a problem
with the electric parking brake
system or the automatic brake
hold system.
Parking Brake
and Brake
System Indicator
(Amber)
(Amber)
●
●
Comes on if the brake system is
deactivated temporarily after the
12-volt battery has been
Drive a short distance at more than 12
mph (20 km/h). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
disconnected, then re-connected.
●
●
●
●
Comes on if there is a problem
with the radar sensor.
Indicator may come on
temporarily when the Maximum
Load Limit is exceeded.
Make sure the total load is within the
Maximum Load Limit.
2 Maximum Load Limit P. 463
Stays on constantly - Have your vehicle
checked by a dealer.
—
92
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
Comes on when the automatic
brake hold system is on.
Automatic Brake
Hold System
Indicator
2 Automatic Brake Hold P. 555
●
●
Comes on when the automatic
brake hold is activated.
Automatic Brake
Hold Indicator
2 Automatic Brake Hold P. 555
—
●
●
Comes on when the engine oil
pressure is low.
Comes on while driving - Immediately
stop in a safe place.
Low Oil Pressure
Indicator
2 If the Low Oil Pressure Indicator
Comes On P. 652
●
●
Comes on if there is a problem
with the electric vehicle system.
Comes on when the High Voltage
battery temperature becomes
high.
Stays on constantly - Have your vehicle
checked by a dealer immediately.
Power System
Indicator
●
Comes on when the vehicle is
ready to drive.
READY
Indicator
2 Turning on the Power P. 469
Continued
93
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
Comes on when the vehicle is
moved by the motor, and the
engine is not operating.
EV Indicator
—
—
Comes on when the vehicle is in
EV mode.
EV Mode
Indicator
2 SPORT HYBRID i-MMD (intelligent
Multi-Mode Drive) P. 11
●
●
After you have set the power
mode to ON, the vehicle performs
system checks.
Readiness codes are part of the on board
diagnostics for the emissions control
systems.
2 Testing of Readiness Codes P. 673
Comes on while driving - Have your
vehicle checked by a dealer.
However, if the readiness codes
have not been set by that time,
this indicator will blink five times
and then go off.
Comes on if there is a problem
with the emissions control systems
or electric vehicle system.
●
●
Comes on when there is no gasoline in the
fuel tank, and goes off after vehicle is
refueled, power mode is turned on,
vehicle is driven, and the power system is
turned off multiple times. If it does not go
off, have your vehicle checked by a dealer.
Blinks while driving - Stop in a safe
place where there are no flammable
objects. Stop the power system for 10
minutes or more, and wait for it to cool
down. Then, take your vehicle to a dealer.
2 If the Malfunction Indicator Lamp
Comes On or Blinks P. 653
●
●
Malfunction
Indicator Lamp
Blinks when a misfire in the
engine's cylinders is detected.
●
94
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
Comes on when there is a
problem with the charging
system.
Stop in a safe place and have your vehicle
checked by a dealer immediately.
2 If the 12-volt Battery Charging
System Indicator Comes On P. 652
12-volt Battery
Charging
System Indicator
●
●
Indicates the current shift
position.
Shift Position
Indicator
2 Shifting P. 477
—
●
The indicated current shift
position blinks if there is a
problem with the transmission
system.
Avoid sudden start and acceleration, and
stop in a safe place immediately.
Have your vehicle checked by a dealer.
Transmission
System Indicator
●
●
●
The indicated current shift
Set the parking brake when parking.
Have your vehicle checked by a dealer
immediately.
position or all the shift positions
blink if you cannot select (P due
to the transmission system failure.
●
●
Comes on when the paddle
selector is pulled.
Blinks when the deceleration does
not occur while pulling the paddle
selector.
Comes on with M when SPORT
mode is selected and pulling the
paddle selector.
Deceleration
Paddle Selector
Indicator
2 Deceleration Paddle Selector P. 484
—
●
Continued
95
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
Comes on when you press the
SPORT button.
The ambient meter remains lit up in red as
long as sport mode is on.
SPORT Mode
Indicator
2 SPORT Mode P. 483
●
●
Blinks and the beeper sounds for a
few seconds if you are not
wearing a seat belt when you set
the power mode to ON, then the
indicator comes on.
If the front passenger is not
wearing a seat belt, the indicator
comes on a few seconds later.
Blinks while driving if you and/or
the front passenger has not
fastened a seat belt. The beeper
sounds and the indicator blinks at
regular intervals.
The beeper stops and the indicator goes
off when you and the front passenger
fasten their seat belts.
Stays on after you and/or the front
passenger has fastened the seat belt(s)
- A detection error may have occurred in
the sensor. Have your vehicle checked by a
dealer.
●
●
Seat Belt
Reminder
Indicator
2 Seat Belt Reminder P. 49
●
●
●
●
Comes on when the fuel reserve is
running low (approximately 2.1
U.S. gal/8.0 Liter left).
Blinks if there is a problem with
the fuel gauge.
Comes on - Refuel your vehicle as soon as
possible.
Blinks - Have your vehicle checked by a
dealer.
Low Fuel
Indicator
96
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
Comes on if there is a problem
with the ABS.
Stays on constantly - Have your vehicle
checked by a dealer. With this indicator
on, your vehicle still has normal braking
ability but no anti-lock function.
Anti-lock Brake
System (ABS)
Indicator
2 Anti-lock Brake System (ABS) P. 557
●
●
Comes on if a problem with any of
the following is detected:
- Supplemental restraint system
- Side airbag system
Stays on constantly - Have your vehicle
checked by a dealer.
Supplemental
Restraint System
Indicator
- Side curtain airbag system
- Seat belt tensioner
●
●
●
Blinks when VSA® is active.
Comes on if there is a problem with
Stays on constantly - Have your vehicle
checked by a dealer.
2 Vehicle Stability AssistTM (VSA®), aka
Electronic Stability Control (ESC),
System P. 489
the VSA system.
®
Vehicle Stability
AssistTM (VSA®)
System Indicator
●
●
Comes on if the VSA® system is
deactivated temporarily after the
12-volt battery has been
Drive a short distance at more than 12 mph
(20 km/h). The indicator should go off. If it
does not, have your vehicle checked by a
dealer.
disconnected, then re-connected.
Continued
97
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
Comes on when you partially
disable VSA®.
2 VSA® On and Off P. 490
Vehicle Stability
AssistTM (VSA®)
OFF Indicator
●
●
Comes on if the VSA® system is
deactivated temporarily after the
12-volt battery has been
Drive a short distance at more than 12 mph
(20 km/h). The indicator should go off. If it
does not, have your vehicle checked by a
dealer.
disconnected, then re-connected.
●
Comes on if there is a problem
with the EPS System.
Stays on constantly - Have your vehicle
checked by a dealer.
Electric Power
Steering (EPS)
System Indicator
2 If the Electric Power Steering (EPS)
System Indicator Comes On P. 656
98
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
May come on briefly if the power
mode is set to ON and the vehicle
is not moved within 45 seconds,
to indicate the calibration process
is not yet complete.
Comes on and stays on when:
- One or more tires’ pressures are
determined to be significantly
low.
Comes on while driving - Stop in a safe
place, check tire pressures, and inflate the
tire(s) if necessary.
Stays on after the tires are inflated to
the recommended pressures - The
system needs to be calibrated.
●
2 TPMS Calibration P. 494
Low Tire
Pressure/TPMS
Indicator
- The system has not been
calibrated.
●
●
●
●
Blinks for about one minute, and
then stays on if there is a problem
with the TPMS.
Blinks and remains on - Have your
vehicle checked by a dealer.
Comes on if the TPMS is
deactivated temporarily after the
12-volt battery has been
Drive a short distance at more than 12 mph
(20 km/h). The indicator should go off. If it
does not, have your vehicle checked by a
dealer.
disconnected, then reconnected.
Continued
99
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
Comes on along with a beep
when a problem is detected. A
system message on the driver
information interface appears at
the same time.
●
●
While the indicator is on, press the
(display/information) button to see the
message again.
Refer to the Indicators information in this
chapter when a system message appears
on the driver information interface.
Respond to the message accordingly.
The driver information interface does not
return to the normal screen unless the
System Message
Indicator
—
●
warning is canceled, or the
pressed.
button is
●
●
●
Blinks when you operate the turn
signal lever.
Blink along with all turn signals
when you press the hazard
warning button.
Does not blink or blinks rapidly
- Have your vehicle checked by a dealer.
Turn Signal and
Hazard Warning
Indicators
—
—
●
Comes on when the high beam
headlights are on.
High Beam
Indicator
—
100
uuIndicatorsu
Indicator
Name
Lights On
On/Blinking
Explanation
Message
●
●
Comes on when the parking, tail,
and other external lights are on.
2 Light Switches P. 190
—
Indicator
Comes on when the fog lights are
on.
Fog Light
Indicator*
2 Fog Lights* P. 194
—
—
●
●
Comes on when all the operating
conditions of the auto high-beam
are met.
Auto High-Beam
Indicator
2 Auto High-Beam P. 195
●
●
●
Blinks if the immobilizer system
cannot recognize the key
information.
Blinks - You cannot start the power
system. Set the power mode to VEHICLE
OFF, then select the ON mode again.
Repeatedly blinks - The system may be
malfunctioning. Have your vehicle checked
by a dealer.
Do not attempt to alter this system or add
other devices to it. Electrical problems can
occur.
Immobilizer
System Indicator
—
Indicator
* Not available on all models
Continued
101
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
Blinks when the security system
alarm has been set.
Security System
Alarm Indicator
2 Security System Alarm* P. 178
—
Indicator
●
●
●
Comes on when the ECON mode
is on.
ECON Mode
Indicator
2 ECON Mode P. 487
Stays on while the blind spot
information system is turned off.
2 Blind spot information System*
P. 499
●
●
Blind spot
information
System
Indicator*
Comes on when mud, snow, or
ice accumulates in the vicinity of
sensor.
Comes on while driving - Remove the
obstacle in the vicinity of the sensor.
2 Blind spot information System*
P. 499
●
Comes on if there is a problem
with the system.
Comes on while driving - Have your
vehicle checked by a dealer.
* Not available on all models
102
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
●
Comes on if there is a problem
with the RDM system.
Stays on constantly - Have your vehicle
checked by a dealer.
Comes on if the RDM is
deactivated temporarily after the
12-volt battery has been
Drive a short distance at more than 12 mph
(20 km/h). The indicator should go off. If it
does not, have your vehicle checked by a
dealer.
Road Departure
Mitigation
(RDM) Indicator
disconnected, then re-connected.
●
●
Comes on when the RDM system
shuts itself off.
Stays on - The temperature inside the
camera is too high.
Use the climate control system to cool
down the camera.
The system activates when the
temperature inside the camera cools
down.
2 Front Sensor Camera P. 548
Continued
103
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
Comes on when the RDM system
shuts itself off.
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place and wipe the debris
off with a soft cloth.
Have your vehicle checked by a dealer if
the indicator and message come back on
after you cleaned the area around the
camera.
2 Front Sensor Camera P. 548
●
●
Indicator may come on temporarily when
passing through an enclosed space, such
as a tunnel.
The area around the radar sensor is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place and wipe the debris
off with a soft cloth. Indicator may take
some time to go off after the radar sensor
is cleaned.
Road Departure
Mitigation
(RDM) Indicator
●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you cleaned the radar sensor.
2 Radar Sensor P. 550
●
●
●
Indicator may come on
temporarily when the Maximum
Load Limit is exceeded.
Make sure the total load is within the
Maximum Load Limit.
2 Maximum Load Limit P. 463
Stays on constantly - Have your vehicle
checked by a dealer.
—
104
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
●
●
Comes on if there is a problem
with ACC with Low Speed Follow.
Comes on while driving - Have your
vehicle checked by a dealer.
Comes on if the ACC with Low
Speed Follow is deactivated
temporarily after the 12-volt
battery has been disconnected,
then re-connected.
Drive a short distance at more than 12 mph
(20 km/h). The indicator should go off. If it
does not, have your vehicle checked by a
dealer.
Adaptive Cruise
Control (ACC)
with Low Speed
Follow Indicator
(Amber)
●
●
●
●
Comes on if there is a problem
with ACC with Low Speed Follow.
Indicator may come on
temporarily when Maximum Load
Limit is exceeded.
Make sure the total load is within the
Maximum Load Limit.
2 Maximum Load Limit P. 463
Stays on constantly - Have your vehicle
checked by a dealer.
—
●
ACC with Low Speed Follow has
been automatically canceled.
Continued
105
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
Adaptive Cruise
Control (ACC)
with Low Speed
Follow Indicator
(Green)
Comes on when you press the
MAIN button.
2 Adaptive Cruise Control (ACC) with
Low Speed Follow P. 517
—
●
●
●
Lane Keeping
Assist System
(LKAS) Indicator
(Amber)
Comes on if there is a problem
with the LKAS.
Stays on constantly - Have your vehicle
checked by a dealer.
Lane Keeping
Assist System
(LKAS) Indicator
(Green)
Comes on when you press the
MAIN button.
2 Lane Keeping Assist System (LKAS)
—
P. 534
106
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
●
●
Comes on when you deactivate
the CMBSTM. A driver information
interface message appears for five
seconds.
Comes on if there is a problem
with the CMBSTM.
Stays on constantly without the
CMBSTM off - Have your vehicle checked
by a dealer.
2 Collision Mitigation Braking
SystemTM (CMBSTM) P. 506
●
●
Comes on if the CMBSTM is
deactivated temporarily after the
12-volt battery has been
Drive a short distance at more than 12 mph
(20 km/h). The indicator should go off. If it
does not, have your vehicle checked by a
dealer.
●
●
Collision
Mitigation
Braking
SystemTM
(CMBSTM)
Indicator
disconnected, then re-connected.
Comes on when the CMBSTM
shuts itself off.
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place, and wipe it off with
a soft cloth.
●
2 Front Sensor Camera P. 548
●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you cleaned the camera.
Continued
107
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message
Comes on when the CMBSTM
shuts itself off.
Indicator may come on temporarily when
passing through an enclosed space, such
as a tunnel.
●
●
●
The area around the radar sensor is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place, and wipe it off with
a soft cloth. Indicator may take some time
to go off after the radar sensor is cleaned.
Have your vehicle checked by a dealer if
the indicator does not go off even after
you clean the sensor cover.
●
●
Collision
Mitigation
Braking
SystemTM
(CMBSTM)
Indicator
2 Radar Sensor P. 550
Stays on - The temperature inside the
camera is too high. Use the climate control
system to cool down the camera. The
system activates when the temperature
inside the camera cools down.
2 Front Sensor Camera P. 548
●
●
●
Indicator may come on
temporarily when the Maximum
Load Limit is exceeded.
Make sure the total load is within the
Maximum Load Limit.
2 Maximum Load Limit P. 463
Stays on constantly - Have your vehicle
checked by a dealer.
—
108
uuIndicatorsuDriver Information Interface Warning and Information Messages
Driver Information Interface Warning and Information Messages
The following messages appear only on the driver information interface. Press the
again with the system message indicator on.
(display/information) button to see the message
Message
Condition
Explanation
●
●
●
Appears if any door or the tailgate is not completely
closed.
Appears if any door or the tailgate is opened while
driving. The beeper sounds.
Disappears when all doors and the tailgate are
closed.
●
Models with parking sensor system
Check if the area around the sensor(s) is covered with
mud, ice, snow, etc. If the indicator(s) stays on even
after you clean the area, have the system checked by
a dealer.
●
Appears if there is a problem with the parking sensor
system.
●
●
If there is a problem with any of the sensors, the all
sensor indicator(s) comes on in red.
●
Appears if there is a problem with the acoustic vehicle
alerting system.
Have your vehicle checked by a dealer immediately.
●
●
Appears when the scheduled maintenance is due soon.
Consequently, Maintenance Due Now and
Maintenance Past Due follow.
2 Maintenance Minder Messages on the Driver
Information Interface P. 583
Continued
109
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
●
Appears if there is a problem with the shutter grille,
and the radiator coolant temperature is too high.
Power output will be reduced, so you may not be
able to accelerate or maintain your current speed.
Have your vehicle checked by a dealer.
Appears when there is a problem with the 12-volt
battery charging system.
Have your vehicle checked by a dealer.
●
●
●
●
Appears if the automatic brake hold is automatically
canceled while it is in operation.
Immediately depress the brake pedal.
Appears when the engine coolant temperature gets
abnormally high.
2 Overheating P. 649
●
Appears when the engine coolant temperature is near
its upper limit.
Drive slowly to prevent overheating.
110
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
Appears if there is a problem with the cooling system.
Drive slowly to prevent overheating and have your
vehicle checked by a dealer as soon as possible.
●
Appears when you set the power mode to ON without
fastening the driver's seat belt.
Fasten the seat belt properly before you start to drive.
(White)
●
●
●
●
●
Appears when you try to change the transmission
without depressing the brake pedal.
Depress the brake pedal, then change the
transmission.
Appears when you try to change the transmission
without releasing your foot off the accelerator pedal.
Release your foot off the accelerator pedal, then
change the transmission.
●
●
Appears when the (P button is pressed while the
vehicle is moving.
Appears if you put the transmission into (R while the
vehicle is moving forward, or into (D while the vehicle
is reversing.
Make sure that the vehicle comes to a stop before
operating the shift button.
Continued
111
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
Appears if there is a problem with the electric system.
Appears when you set the power mode to OFF while
driving.
Immediately stop in a safe place and set the parking
brake, then restart the power system. If the message
disappears, continue driving.
Continue driving if the message goes off soon after.
If there is a problem with the transmission system,
the transmission indicator system comes on.
2 Transmission System Indicator P. 95
●
●
●
●
●
●
Appears when the automatic brake hold system is
turned off.
2 Automatic Brake Hold P. 555
●
●
Appears when the automatic brake hold button is
pressed without wearing the driver’s seat belt.
Fasten the driver’s seat belt.
2 Automatic Brake Hold P. 555
Appears when the automatic brake hold button is
pressed without depressing the brake pedal while the
automatic brake hold is in operation.
Press the automatic brake hold button with the brake
pedal depressed.
2 Automatic Brake Hold P. 555
Appears when the parking brake is applied
automatically while it is in operation.
2 Automatic Brake Hold P. 555
2 Parking Brake P. 551
112
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
●
●
Appears when the electric parking brake switch is
pressed without depressing the brake pedal while the
electric parking brake is in operation.
Press the electric parking brake switch with the brake
pedal depressed.
2 Parking Brake P. 551
●
Appears when the vehicle is no longer able to run due
to a malfunction.
Immediately stop in a safe place.
●
●
Appears when there is a risk that the vehicle will move
unexpectedly after you have stopped due to a
malfunction with the vehicle.
While the vehicle is stopped, apply the parking brake.
2 Parking Brake P. 551
Have your vehicle checked by a dealer.
●
Appears as soon as a problem is detected in the keyless
access system or push button starting system.
Appears constantly - Have your vehicle checked by
a dealer.
●
●
Appears when you close the door with the power
mode in ON without the keyless remote inside the
vehicle.
Disappears when you bring the keyless remote back
inside the vehicle and close the door.
2 Keyless Remote Reminder P. 188
Continued
113
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
●
●
●
Appears when the keyless remote battery becomes
weak.
2 Replacing the Remote Battery P. 617
Appears when you set the power mode to ACCESSORY
or ON.
2 Turning on the Power P. 469
Appears if you press the POWER button while the
vehicle is moving.
2 Emergency Power System Off P. 646
Appears when the power mode is in ACCESSORY.
—
●
●
Appears after the driver’s door is opened when the
power mode is in ACCESSORY.
Change the power mode to VEHICLE OFF.
2 POWER Button P. 186
Appears if the keyless remote’s battery is too weak to
turn on the power system or the key is not within
operating range to turn on the power system. The
beeper sounds six times.
Bring the back of the keyless remote into contact
with the POWER button.
2 If the Keyless Remote Battery is Weak P. 645
114
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
Appears when you press and hold (N button for more
than two seconds.
Disappears when you set the shift position to a shift
other than (N.
2 If you want to keep the transmission in (N
position [car wash mode] P. 481
●
●
●
Appears when the vehicle is stopped with the driver’s
seat belt unfastened and there is a chance that the
vehicle may roll unintentionally.
Press the (P button before release the brake pedal
when idling, parking or exiting the vehicle.
2 Shift Operation P. 479
●
●
Appears when the power system temperature is high.
Your vehicle has less ability to accelerate and may be
harder to start on an incline.
Park in a safe place, and cool the system down.
2 Overheating P. 649
●
●
●
Appears when the High Voltage battery temperature is
low.
Your vehicle has less ability to accelerate and may be
harder to start on an incline.
Goes off once you start driving as the High Voltage
battery warms up.
●
●
●
Appears after the 12-volt battery charging system
indicator comes on.
Your vehicle has less ability to accelerate and may be
harder to start on an incline.
Contact a dealer immediately.
●
●
Appears when the High Voltage battery temperature is
too low to operate (approx. -22°F [-30°C] or below).
You can start the engine and use the climate control
system to warm up the interior, which will also warm
the High Voltage battery enough for you to drive the
vehicle.
Continued
115
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
Appears when the High Voltage battery and other
system control temperatures are too low to operate
(approx. -40°F [-40°C] or below).
You must wait for an increase in the ambient
temperature or move the vehicle to a warmer
location.
●
●
Consult a dealer if necessary.
Appears if the power system is in diagnostic mode.
You may notice a decrease in available power. Have
your vehicle checked by a dealer.
As a result of diagnostics, the power system indicator
may come on.
●
2 Power System Indicator P. 93
●
●
Appears when you have met following situations and
EV mode is canceled.
EV mode is available once the condition is improved
or the cause that canceled EV mode is cleared.
- Battery Temperature At Limit.
- Battery Charge Too Low.
- Engine Too Cold.
- Cabin Being Heated.
- Speed Too High.
- Hard Acceleration Requested.
●
●
Appears when you depress the accelerator pedal while
the shift position is in (N.
Remove your foot off the accelerator pedal. When
driving, depress the brake pedal and operate the shift
position.
116
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
●
Appears when you put the transmission into (N, then
release the (N button.
2 If you want to keep the transmission in (N
position [car wash mode] P. 481
●
Appears when you repeatedly change the shift position
between (P and other positions in short period.
Take some time before changing the shift position.
Appears if the engine needs to be started when you
press the EV button.
—
●
Appears when you have met following situations and
EV mode has been automatically canceled.
- When the High Voltage battery charge is low.
- When the velocity of your vehicle is high.
- When your vehicle's speed exceeds 25 mph (40 km/h)
before the engine warms up enough.
EV mode is available once the condition is improved
or the cause that canceled EV mode is cleared.
- When depressing the accelerator pedal deeply.
- When driving on a slope.
●
●
Appears when the High Voltage battery is running
extremely low.
Contact a dealer immediately.
Continued
117
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
●
Appears if there is a problem with the automatic
lighting control system.
Appears while driving - Manually turn the lights
on, and have your vehicle checked by a dealer.
Appears if there is a problem with the headlights.
Appears while driving - The headlights may not be
on.
When conditions allow you to drive safely, have your
vehicle checked by a dealer as soon as possible.
●
●
Appears when you unlock and open the driver’s door
while the power system is on by remote engine start.
2 Remote Engine Start P. 471
Appears if the vehicle is being driven in a manner
consistent with drowsy or inattentive driving.
2 Driver Attention Monitor P. 135
●
●
Appears when ACC with Low Speed Follow has been
automatically canceled.
You can resume the set speed after the condition
that caused ACC with Low Speed Follow to cancel
improves. Press the RES/+ button.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
118
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
Appears when the distance between your vehicle and
the vehicle ahead of you is too close while ACC with
Low Speed Follow is in operation.
ACC with Low Speed Follow has been automatically
canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
●
●
●
●
Appears when pressing the –/SET button while the
distance between your vehicle and the vehicle ahead of
you is too close.
ACC with Low Speed Follow cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears when the driver’s seat belt is unfastened while
your vehicle is automatically stopped by ACC with Low
Speed Follow.
ACC with Low Speed Follow has been automatically
canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
●
●
●
●
●
●
Appears when pressing the –/SET button while the
driver’s seat belt is unfastened.
ACC with Low Speed Follow cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears when the speed of the vehicle is too high for
you to set ACC.
Reduce the speed, then set ACC.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears when ACC is canceled due to excessive high
vehicle speed.
Reduce the speed, then reset ACC.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Continued
119
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
●
●
●
Appears when the vehicle ahead of you resumes
driving, after your vehicle has been stopped
automatically by ACC with Low Speed Follow.
Press the RES/+ button or –/SET button or depress
the accelerator pedal.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears if the VSA® or traction control function
operates while ACC with Low Speed Follow is in
operation.
ACC with Low Speed Follow has been automatically
canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears when the shift position is changed to any
position other than (D while ACC with Low Speed
Follow is in operation.
ACC with Low Speed Follow has been automatically
canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
●
●
●
●
Appears when pressing the –/SET button while the
shift position is in any position other than (D.
ACC with Low Speed Follow cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears when the vehicle is stopped on a very steep
slope while ACC with Low Speed Follow is in
operation.
ACC with Low Speed Follow has been automatically
canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
120
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
Appears when pressing the –/SET button while the
vehicle is stopped on a very steep slope.
ACC with Low Speed Follow cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
●
●
Appears when the parking brake is applied
automatically while ACC with Low Speed Follow is in
operation.
ACC with Low Speed Follow has been automatically
canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
2 Parking Brake P. 551
●
●
Appears when pressing the –/SET button while the
parking brake is applied.
ACC with Low Speed Follow cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
2 Parking Brake P. 551
●
●
●
●
Appears when pressing the –/SET button while the
vehicle is moving and the brake pedal is depressed.
ACC with Low Speed Follow cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
Appears if ACC with Low Speed Follow is canceled
while your vehicle is automatically stopped by ACC
with Low Speed Follow.
Immediately depress the brake pedal.
Continued
121
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
Flashes when the system senses a likely collision with a
vehicle in front of you.
Take appropriate action to prevent a collision (apply
the brakes, change lanes, etc.)
2 Adaptive Cruise Control (ACC) with Low Speed
Follow P. 517
2 Collision Mitigation Braking SystemTM (CMBSTM
)
P. 506
●
Lane Keeping Assist System (LKAS)
Keep the vehicle within the lane you are driving.
●
2 Lane Keeping Assist System (LKAS) P. 534
Appears when the vehicle is driving out of a detected
lane. The steering wheel vibrates rapidly.
●
●
Road Departure Mitigation (RDM) System
Keep the vehicle within the lane you are driving.
2 Road Departure Mitigation (RDM) System P. 543
You can change the setting for the road departure
mitigation system. Narrow, Normal, Wide, and
Warning Only can be selected.
●
Appears when the vehicle is driving out of a detected
lane.
When you selected Warning Only
- The steering wheel vibrates rapidly when the vehicle is
drifting out of a detected lane.
2 Customized Features P. 140, 369
When you selected Narrow, Normal or Wide
- The steering wheel vibrates rapidly when the vehicle is
drifting out of a detected lane. The system also steers
the vehicle to help you remain within your driving
lane.
122
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
Road Departure Mitigation (RDM) System
When you selected Narrow
●
Appears when the vehicle is likely to drive out of a
detected lane.
—
The RDM system also steers the vehicle to help you
remain within your driving lane.
●
●
●
●
Blinks when you fail to steer the vehicle. The beeper
sounds simultaneously.
Operate the steering wheel to resume the LKAS.
Appears when the LKAS is in operation, or the LKAS
button is pressed, but there is a problem with a system
related to the LKAS. The LKAS cancels automatically.
The beeper sounds simultaneously if selected by
customization.
If any other system indicators come on, such as the
VSA®, ABS and brake system, take appropriate
action.
2 Indicators P. 90
●
●
●
●
Appears if anything covers the radar sensor cover and
prevents the sensor from detecting a vehicle in front.
May appear when driving in bad weather (rain, snow,
fog, etc.)
When the radar sensor gets dirty, stop your vehicle in
a safe place, and wipe off dirt using a soft cloth. The
message may take some time to go off.
Have your vehicle checked by a dealer if the message
does not disappear even after you clean the sensor
cover.
2 Radar Sensor P. 550
2 Honda Sensing® P. 503
Continued
123
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
Appears if the temperature inside the front sensor
camera is too high and some driver assist systems
cannot be activated.
Use the climate control system to cool down the
camera.
Disappears - The camera has been cooled down
and the systems are activated normally.
2 Front Sensor Camera P. 548
2 Honda Sensing® P. 503
●
●
●
●
Appears if the area around the front sensor camera is
blocked by dirt, mud, etc. and be prevented from
detecting a vehicle in front.
May appear when driving in bad weather (rain, snow,
fog, etc.)
When the front window gets dirty, stop your vehicle
in a safe place, and wipe it off with a soft cloth.
Have your vehicle checked by a dealer if the message
does not disappear even after you cleaned the area
around the camera.
2 Front Sensor Camera P. 548
2 Honda Sensing® P. 503
●
●
●
Appears if there is a problem with the auto high-beam.
Manually operate the headlight switch.
If you are driving with the high beam headlights
when this happens, the headlights are changed to
low beams.
124
uuIndicatorsuDriver Information Interface Warning and Information Messages
Message
Condition
Explanation
●
●
●
Appears if there is a problem with the real time AWD
with intelligent control systemTM.
The engine drives the front wheels only in this state.
Have your vehicle checked by a dealer.
●
Appears when the differential temperature is too high.
Stop in a safe place, change to (P, and idle the
engine until the message disappears. If the message
does not disappear, have your vehicle checked by a
dealer.
2 Real Time AWD with Intelligent Control
SystemTM P. 492
Models with power tailgate
Message
Condition
Explanation
●
●
●
Appears when there is a problem with the power
tailgate system.
Manually open or close the power tailgate.
Have your vehicle checked by a dealer.
Models with color audio system
Message
Condition
Explanation
●
Appears while you are customizing the settings and the
shift position changed out of (P.
2 Customized Features P. 140
125
