Deutsch
EnglishMaintenance -> Engine Oil Check for your Ford Kuga 2019-2025
Maintenance
7. Reinstall the dipstick. Make sure it is
ENGINE OIL DIPSTICK - FULL
HYBRID ELECTRIC VEHICLE
(FHEV), PLUG-IN HYBRID
ELECTRIC VEHICLE (PHEV)
fully seated.
Note: The oil consumption of new engines
reaches its normal level after approximately
5,000 km (3,000 mi).
Adding Engine Oil
WARNING: Do not add engine oil
when the engine is hot. Failure to follow
this instruction could result in personal
injury.
WARNING: Do not remove the filler
cap when the engine is running.
Do not use supplemental engine oil
additives because they are unnecessary
and could lead to engine damage that the
vehicle warranty may not cover.
E250320
A
B
C
Minimum.
Nominal.
Maximum.
1. Clean the area surrounding the engine
oil filler cap before you remove it.
2. Remove the engine oil filler cap.
3. Add engine oil that meets our
ENGINE OIL CHECK
specifications.
4. Reinstall the engine oil filler cap. Turn
it clockwise until you feel a strong
resistance.
Note: Do not add oil further than the
maximum mark. Oil levels above the
maximum mark may cause engine damage.
1. Make sure that your vehicle is on level
ground.
2. Check the oil level before starting the
engine, or switch the engine off and
wait 10 minutes for the oil to drain into
the oil pan.
Note: Immediately soak up any oil spillage
3. Remove the dipstick and wipe it with
with an absorbent cloth.
a clean, lint-free cloth.
4. Reinstall the dipstick and make sure it
is fully seated.
5. Remove the dipstick again to check the
oil level.
Note: If the oil level is between the
maximum and minimum marks, the oil level
is acceptable. Do not add oil.
6. If the oil level is at the minimum mark,
immediately add oil.
371
Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing
Maintenance
OIL CHANGE INDICATOR
Message
Action and description
RESET - 1.5L ECOBOOST™,
FULL HYBRID ELECTRIC
VEHICLE (FHEV), PLUG-IN
HYBRID ELECTRIC VEHICLE
(PHEV)
If the instrument cluster
displays one of the following
messages, repeat the
process.
Not reset
Reset cancelled
Use the information display controls on
the steering wheel to reset the oil change
indicator.
ENGINE COOLANT CHECK
From the main menu scroll to:
Message
Action and description
WARNING: Do not remove the
coolant reservoir cap when the engine is
on or the cooling system is hot. Wait 10
minutes for the cooling system to cool
down. Cover the coolant reservoir cap
with a thick cloth to prevent the
Settings
Press the right arrow button,
then from this menu scroll
to the following message.
Vehicle
settings
Press the right arrow button,
then from this menu scroll
to the following message.
possibility of scalding and slowly remove
the cap. Failure to follow this instruction
could result in personal injury.
Oil life
Press the right arrow button,
then from this menu scroll
to the following message.
WARNING: Do not put coolant in
the windshield washer reservoir. If
sprayed on the windshield, coolant could
make it difficult to see through the
windshield.
Hold OK to Press and hold the OK
reset
button until the instrument
cluster displays the
following message.
WARNING: To reduce the risk of
personal injury, make sure the engine is
cool before unscrewing the coolant
pressure relief cap. The cooling system
is under pressure. Steam and hot liquid
can come out forcefully when you loosen
the cap slightly.
Reset successful
When the oil change indic-
ator resets the instrument
cluster displays 100%.
Remaining oil life
{##0}%
WARNING: Do not add coolant
further than the MAX mark.
When the engine is cold, check the
concentration and level of the coolant at
the intervals listed in the scheduled
maintenance information.
372
Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing
