Deutsch
EnglishSelective Catalytic Reduction System -> Filling the Selective Catalytic Reduction System Tank for your Ford Focus 2018-2025
Selective Catalytic Reduction System
•
Store the AdBlue® at temperatures
FILLING THE SELECTIVE
CATALYTIC REDUCTION
SYSTEM TANK
between -5°C (23°F) and 20°C
(68°F).
•
•
Do not store AdBlue® containers in
your vehicle.
Filling the Selective Catalytic
Reduction System Tank in Cold
Weather
AdBlue® is non-flammable, non-toxic,
colorless and water-soluble.
AdBlue® may freeze when the
temperature is below -11°C (12°F). Your
vehicle has a preheating system which
allows the fluid to operate below -11°C
(12°F). If you overfill the AdBlue® tank and
the fluid freezes, it may cause damage not
covered by the vehicle Warranty.
Note: It may not be possible to fully fill the
AdBlue® tank when the temperature is
below -11°C (12°F).
Note: If the AdBlue® tank is frozen, it could
not correctly display the fluid level or
recognize when you fill the tank. The
AdBlue® level updates when the tank
completely thaws out.
E204215
Filling the Selective Catalytic
Reduction System Tank Using a
Fuel Station Pump
Filling the AdBlue® tank using a fuel
station pump is similar to refueling your
vehicle.
The AdBlue® tank filler pipe is next to the
fuel tank filler pipe and has a blue cap. Fill
the tank using a fluid pump at an AdBlue®
filling station or an AdBlue® container.
1. Fully open the fuel filler door.
E268809
229
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
Selective Catalytic Reduction System
2. Remove the AdBlue® tank filler cap.
3. Fully insert the AdBlue® pump nozzle.
2. Place the spout on to the container and
tighten it until you feel a strong
resistance.
E268809
3. Remove the AdBlue® tank filler cap.
E268817
4. Insert the spout into the AdBlue® tank
filler pipe until the seal on the spout
fully seats.
4. Operate the AdBlue® pump nozzle
within the area shown.
5. Pour the fluid into the tank.
Note: The pump nozzle shuts off when the
Note: The fluid stops flowing when the
tank is full.
tank is full.
5. Slightly raise the AdBlue® pump nozzle
6. Return the container to the vertical
position slightly below the AdBlue®
tank filler pipe.
and then slowly remove it.
6. Replace the AdBlue® tank filler cap.
Turn it clockwise until you feel a strong
resistance and it clicks.
Do not attempt to start the engine if you
have filled the AdBlue® tank with incorrect
fluid. Incorrect fluid use could cause
damage not covered by the vehicle
Warranty. Have your vehicle checked as
soon as possible.
7. Allow any fluid remaining in the spout
to drain back into the container.
8. Remove the spout from the AdBlue®
tank filler pipe.
9. Remove the spout from the AdBlue®
container and replace the cap.
10. Replace the AdBlue® tank filler cap.
Turn it clockwise until you feel a
strong resistance and it clicks.
Do not attempt to start the engine if you
have filled the AdBlue® tank with incorrect
fluid. Incorrect fluid use could cause
damage not covered by the vehicle
Warranty. Have your vehicle checked as
soon as possible.
Filling the Selective Catalytic
Reduction System Tank Using a
Portable Container
Use containers that have a seal on the
spout.
Always follow the manufacturer's
instructions.
1. Remove the fluid container cap.
230
Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing
