Deutsch
EnglishStarting and Stopping the Engine -> Ignition Switch for your Ford Fiesta 2017-2023
Starting and Stopping the Engine
GENERAL INFORMATION
IGNITION SWITCH
WARNING: Extended idling at high
engine speeds can produce very high
temperatures in the engine and exhaust
system, creating the risk of fire or other
damage.
WARNING: Do not park, idle or
drive your vehicle on dry grass or other
dry ground cover. The emission system
heats up the engine compartment and
exhaust system, creating the risk of fire.
WARNING: Do not start the engine
in a closed garage or in other enclosed
areas. Exhaust fumes can be toxic.
Always open the garage door before you
start the engine.
E247596
WARNING: Exhaust leaks may
result in entry of harmful and potentially
lethal fumes into the passenger
Note: Make sure the key is clean before
inserting it into any lock cylinder.
compartment. If you smell exhaust
fumes inside your vehicle, have your
vehicle inspected immediately. Do not
drive if you smell exhaust fumes.
Note: Do not leave the key in the ignition
for an extended period of time when the
engine is not running. This is to prevent the
vehicle battery from losing charge.
Switching the Ignition Off
Turn the key to position 0.
If you disconnect the battery, your vehicle
may exhibit some unusual driving
characteristics for approximately 8 km
(5 mi) after you reconnect it. This is
because the engine management system
must realign itself with the engine. You
can disregard any unusual driving
Switching the Ignition to
Accessory Mode
Turn the key to position I. Electrical
accessories, for example the radio, operate
without the engine running.
characteristics during this period.
The powertrain control system meets all
Canadian interference-causing equipment
standard requirements regulating the
impulse electrical field or radio noise.
When you start the engine, avoid pressing
the accelerator pedal before and during
operation. Only use the accelerator pedal
when you have difficulty starting the
engine.
Switching the Ignition On
Turn the key to position II. All electrical
circuits and accessories are operational
and the warning lamps and indicators
illuminate.
123
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
Starting and Stopping the Engine
Starting the Engine
Starting The Engine - Vehicles with
Manual Transmission (If Equipped)
Turn the key to position III. Release the
key when the engine starts.
1. Fully press the clutch pedal.
2. Press the push button ignition switch.
PUSH BUTTON IGNITION
SWITCH
Note: If you release the clutch pedal during
engine starting, the engine stops cranking.
Starting The Engine - Vehicles with
Switching the Ignition On to
Automatic Transmission (If Equipped)
Accessory Mode
1. Fully press the brake pedal.
2. Shift into park (P).
3. Press the push button ignition switch.
Note: If you release the brake pedal during
engine starting, the engine stops cranking.
Vehicles with a Diesel Engine(If
Equipped)
Note: The engine does not crank until the
glow plug indicator turns off. This may take
several seconds in extremely cold
conditions.
E144447
Press the push button ignition switch once
without your foot on the brake or clutch
pedal. It is on the instrument panel near
the steering wheel. All electrical circuits
and accessories are operational and the
warning lamps and indicators illuminate.
Press the push button ignition switch again
without your foot on the brake or clutch
pedal to switch the ignition off.
Note: The system may not function if the
passive key is close to metal objects or
electronic devices, for example keys or a cell
phone.
Note: The ignition turns off if you leave your
vehicle unattended. This is to prevent the
vehicle battery from losing charge.
Failure to Start - Vehicles with
Manual Transmission (If Equipped)
The system does not function if:
•
The passive key frequencies are
jammed.
•
The key battery has no charge.
If you are unable to start the engine, do the
following:
1. Insert the passive key into the backup
position. See Passive Key Backup
Position (page 44).
2. With the passive key in this position,
you can use the push button ignition
switch to switch the ignition on and
start the engine.
If the engine does not crank after you fully
press the clutch pedal and press the push
button ignition switch, do the following:
Note: A valid passive key must be inside
your vehicle to switch the ignition on and
start the engine.
124
Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing
