Deutsch
EnglishCONTROLS -> Driving for your BMW X1 2022-2025
Driving
CONTROLS
Driving
Driving off
To drive off with the vehicle, proceed as fol-
lows:
Vehicle features and options
This chapter describes model-specific equip-
ment, systems, and functions that are currently
available, or may become available in the fu-
ture, even if they are not present in the vehicle.
1. Depress the brake pedal.
2. Press the Start/Stop button.
Drive-ready state is turned on.
Additional information:
3. Engage the desired selector lever position,
e.g., D or R.
Vehicle equipment, refer to page 8.
4. Release the parking brake.
Start/Stop button
5. To drive off, release the brake pedal and
press the accelerator pedal.
Principle
The Start/Stop button is used to turn vehicle
operating states on/off.
Auto Start/Stop function
Principle
Overview
The Auto Start/Stop function helps save fuel.
The system switches off the engine during a
stop, for instance in traffic jam or at traffic
lights. Drive-ready state remains on despite
the engine being stopped. The engine starts
automatically for driving off.
The Auto Start/Stop function switches to
standby state whenever the engine is started
using the Start/Stop button.
The function is activated at low speeds.
The Start/Stop button is located on the
center console.
Engine stop
Turning on the drive-ready state
Functional requirements
Drive-ready state turns on when the brake
pedal is pressed while pushing the Start/Stop
button.
When stopping, the engine switches off auto-
matically if the following requirements are met:
▷
▷
Selector lever is in selector lever position D.
Pushing the Start/Stop button again will turn
off drive-ready state and turn on standby state.
The brake pedal remains depressed while
the vehicle is at a standstill, or the vehicle is
held by Automatic Hold.
Additional information:
▷
▷
Drive-ready state, refer to page 41.
Standby state, refer to page 41.
▷
The driver's seat belt is buckled, or the driv-
er's door is closed.
120
Driving
CONTROLS
▷
▷
▷
▷
▷
▷
▷
At higher elevations.
The hood is unlocked.
Manual engine stop
If the engine does not shut off automatically
when the vehicle is stopped, the engine can be
shut off manually as follows:
Hill Descent Control is activated.
For stop-and-go traffic.
▷
By quickly depressing the brake pedal from
its current position.
Selector lever position is S, L, or R.
After reversing.
▷
By engaging selector lever position P.
If a traffic situation is detected that is likely
to have a very short stop time, e.g., stop-
ping at a stop sign.
When all functional preconditions are fulfilled,
the engine switches off.
Automatic climate control with engine
switched off
Starting the engine
The automatic climate control system's air flow
is reduced when the engine is switched off.
Functional requirements
When driving off, the engine starts automati-
cally if the following requirements are met:
Display in the instrument cluster
▷
▷
By releasing the brake pedal.
The READY indicator on the
instrument cluster shows that
the Auto Start/Stop function is
ready to start the engine auto-
matically.
If the accelerator pedal is pressed when
Automatic Hold is activated.
Driving off with the Auto Start/Stop
function
To drive off, accelerate normally after starting
the engine.
Functional limitations
The engine does not switch off automatically in
situations like the following:
Safety mode
If one of the following conditions is met, the
engine will not start automatically after it has
been stopped automatically:
▷
▷
In case of a steep downhill grade.
Brake pedal was not depressed hard
enough.
▷
▷
▷
▷
When the ambient temperature is high and
automatic climate control is switched on.
▷
The driver’s seat belt is unbuckled, and the
driver’s door is open.
Vehicle interior has not yet been heated or
cooled as desired.
▷
The hood has been unlocked.
Some indicator lights illuminate for a varied
length of time.
Condensation is about to form on windows
and automatic climate control is on.
The engine can only be started using the Start/
Stop button.
Engine or other components are not at op-
erating temperature.
System limits
Even if driving off was not intended, the deac-
tivated engine starts up automatically in the
following situations:
▷
▷
Engine cooling is required.
Without Mild Hybrid technology: The
wheels are at a sharp angle or the steering
wheel is being turned.
▷
Vehicle battery is deeply discharged.
121
Driving
CONTROLS
▷
▷
▷
▷
When the vehicle interior is excessively
warm, and the air conditioning is on.
Switching off the vehicle during an
automatic engine stop
If the engine stops automatically, the vehicle
can be parked safely, for example to leave it.
When the vehicle interior is excessively
cool, and the heating is on.
Condensation is about to form on windows
and automatic climate control is on.
1. Press the Start/Stop button.
▷
▷
▷
Drive-ready state is switched off.
Standby state is switched on.
Without mild hybrid technology:
In case of a steering operation.
Selector lever position P is engaged au-
tomatically.
▷
When changing the selector lever position
from D or P to R.
2. Engage the parking brake.
▷
▷
If the vehicle battery is deeply discharged.
When starting an oil level measurement.
Automatic deactivation
In certain situations, the Auto Start/Stop func-
tion is deactivated automatically for safety rea-
sons, for instance if no driver is detected.
Deactivating the system manually
Principle
In certain driving situations, e.g., traffic jams,
it may be helpful to deactivate Auto Start/
Stop manually. The engine will then no longer
switch off automatically.
Malfunction
Auto Start/Stop no longer shuts off the engine
automatically in the event of a malfunction. A
Check Control message is displayed on the
instrument cluster. You may continue driving.
Have the vehicle checked by an authorized
service center or another qualified service cen-
ter or repair shop.
If this function is deactivated while the engine
is being stopped automatically, the engine will
start.
Via iDrive
1. To manually activate Auto Start/Stop, go
through the menu as follows: Apps menu /
"Vehicle" / "Driving settings" / "Drivetrain
and chassis" / "Activate Auto Start/Stop".
Steptronic transmission
Principle
2. Select the desired setting.
The Steptronic transmission is the vehicle's
automatic transmission. The shift paddles can
be used to shift gear manually as necessary.
Via selector lever position or drive
mode
The Auto Start/Stop function is deactivated in
the following situations:
Safety information
▷
▷
▷
When selector lever position S is engaged.
When selector lever position L is engaged.
Warning
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of accident,
injury, and property damage. Before leaving
your vehicle, secure it against rolling away,
e.g., by applying the parking brake.
If SPORT or SPORT PLUS driving mode is
selected in My Modes.
122
Driving
CONTROLS
P is engaged automatically
Selector lever positions
Selector lever position P engages automati-
cally in situations like the following:
Gear position D
In selector lever position D, all gears for for-
ward travel are shifted automatically.
▷
After drive-ready state is switched off, if
selector lever position R, D, S, or L is en-
gaged.
The vehicle drives off slowly when the brake
pedal is released.
▷
▷
After standby state is switched off, if selec-
tor lever position N is engaged.
Additional information:
The driver's seat belt is unbuckled and the
driver's door is opened while the vehicle is
stationary and selector lever position D, S,
L, or R is engaged.
Automatic Hold, refer to page 132.
With shift paddles: S for SPORT
program
Selector lever position S is the gear position
used for sportier driving.
The vehicle may begin to move if selector lever
position P is not engaged and the parking
brake is not applied before leaving the vehicle.
The vehicle drives off slowly when the brake
pedal is released.
Additional information:
Parking brake, refer to page 130.
R reverse gear
To reverse, engage selector lever position R.
Only engage reverse gear when the vehicle is
stationary.
Engaging selector lever positions
General information
If a gear position or reverse gear is engaged,
the vehicle will move if the brake pedal is not
pressed when driving off.
The vehicle drives off slowly when the brake
pedal is released.
In certain situations, e.g., to rock free on snow,
it is possible to shift between reverse gear and
gear position D without pressing the brake.
N Neutral
To push the vehicle or have it coast without
using the drive system, engage selector lever
position N, e.g., in car washes.
Functional requirements
To change from selector lever position P to an-
other selector lever position, drive-ready state
must be on and the brake pedal must be de-
pressed.
Without shift paddles: L for LOW mode
In selector lever position L, the transmission
continues to shift automatically, but generally
with lower gears.
Selection lever position P cannot be disen-
gaged until all technical prerequisites are met.
The vehicle drives off slowly when the brake
pedal is released.
Engaging a selector lever position
To engage the selector lever position, proceed
as follows:
Parking position P
General information
In selector lever position P, the drive is blocked
by the transmission, e.g., to park the vehicle.
1. Fasten the driver’s seat belt.
2. Tilt or pull the selector lever in the desired
direction, past the resistance point as nec-
123
Driving
CONTROLS
essary. The selector lever automatically re-
turns to the center position when released.
if the vehicle is meant to coast, e.g., in a car
wash.
To engage selector lever position N, proceed
as follows:
1. Depress the brake pedal.
2. Switch on drive-ready state.
3. If necessary, loosen the belt.
4. If necessary, open the door.
5. Engage selector lever position N.
6. Switch off drive-ready state.
Engaging selector lever position P
In this way, standby state remains switched
on, and a Check Control message is dis-
played.
The vehicle can roll.
The parking brake is engaged automatically
after approx. 35 minutes.
If the system is not operational, you may not
be able to change the selector lever position.
If necessary, release the transmission lock
electronically.
To engage selector lever position P,
press the parking brake button on the
center console.
Additional information:
Electronic unlocking of the transmission lock,
refer to page 125.
The parking brake is applied and the transmis-
sion lock is engaged.
Kickdown
The maximum driving performance is achieved
with kickdown.
Rolling or pushing the vehicle
Step on the accelerator pedal beyond the re-
sistance point at the full throttle position.
Principle
In some situations, the vehicle is supposed to
coast without power for a short distance, e.g.,
in a car wash or when being pushed.
Without shift paddles: LOW mode
Principle
Engaging selector lever position N
LOW mode is recommended to increase the
engine braking effect, e.g., on steep downhill
gradients.
NOTICE
Selector lever position P is automatically en-
gaged when standby state is switched off.
The wheels are blocked. There is a risk of
property damage. Do not switch off standby
124
Driving
CONTROLS
General information
Activating the Sport program
In LOW mode, the transmission continues
shifting automatically, but generally in lower
gears than in selector lever position D.
LOW mode can therefore also be used to ac-
celerate more quickly.
LOW mode can also be used to rock the ve-
hicle free in snow. To do so, shift between re-
verse gear and gear position D without press-
ing the brake.
To activate the Sport program, pull the selector
lever from selector lever position D to D/S.
Enabling LOW mode
The engaged gear is displayed in the instru-
ment cluster, for instance S1.
The sport program of the transmission is acti-
vated.
Ending the Sport program
To cancel the Sport program, move the selec-
tor lever to D/S.
D is displayed in the instrument cluster.
To activate LOW mode, pull the selector lever
from selector lever position D to D/L.
Displays in the instrument cluster
The engaged gear is displayed in the instru-
ment cluster, for instance L1.
The selector lever position, for
example, P, is shown on the in-
strument cluster.
The transmission's LOW mode is enabled.
Exiting LOW mode
To exit LOW mode, pull the selector lever to
D/L.
Electronic unlocking of the
transmission lock
D is displayed in the instrument cluster.
With shift paddles: S program
Principle
The S program's shift points and shift times
are designed for sportier handling. The trans-
mission, for instance shifts up later and the
shifting times are shorter.
General information
To maneuver the vehicle out of a hazardous
area, release the transmission lock electroni-
cally.
Before unlocking the transmission lock, secure
the vehicle against rolling away, for instance
with a wheel chock.
125
Driving
CONTROLS
▷
▷
Pull and hold the right shift paddle until D is
displayed in the instrument cluster.
Engaging selector lever position N
To engage selector lever position N, proceed
as follows:
In addition to the pulled right shift paddle,
pull the left shift paddle.
1. Quickly push the Start/Stop button three
times without pressing the brake.
Continuous manual mode
In Sport program S, pulling a shift paddle
switches to manual mode M.
2. Depress the brake pedal.
3. Within 30 seconds, push the selector lever
into position N until position N is shown on
the selector lever.
The engaged gear is displayed in the instru-
ment cluster, for instance M1.
An appropriate Check Control message is
displayed.
It is possible to switch into automatic mode:
▷
▷
▷
Pull and hold the right shift paddle until S is
displayed on the instrument cluster.
4. Maneuver the vehicle from the hazardous
area and secure it against rolling away.
In addition to the pulled right shift paddle,
pull the left shift paddle.
Shift paddles
Pull the selector lever to D/S.
If M2 is set manually when the vehicle is sta-
tionary, the transmission no longer shifts down
to M1.
Principle
The shift paddles on the steering wheel are
used to change gears manually.
Shifting
General information
Shifting
The vehicle only shifts at suitable RPM and
road speeds.
Even in manual mode, the transmission shifts
automatically in certain situations, e.g., when
speed limits are reached.
▷
▷
To upshift, pull the right shift paddle.
To downshift, pull the left shift paddle.
Temporary manual mode
In selector lever position D, pulling a shift pad-
dle switches into manual mode temporarily.
The selected gear is shown briefly on the
instrument cluster, then the current gear is
shown again.
The engaged gear is also displayed in the in-
strument cluster, for instance D1.
After conservative driving in manual mode
without acceleration or shifting via the shift
paddles for a certain amount of time, the
transmission switches back to automatic
mode.
It is possible to switch into automatic mode:
126
Driving
CONTROLS
Do not use Launch Control when breaking in
the vehicle.
Advanced mode
General information
Additional information:
Depending on vehicle equipment, the Step-
tronic transmission offers an advanced mode
with adapted shift characteristics.
Break-in, refer to page 304.
Functional requirement
▷
Automatic downshift to lowest possible
gear.
Launch Control can be used when the engine
is at operating temperature. The engine is at
operating temperature after an uninterrupted
trip of at least 6 miles/10 km.
To have the Steptronic transmission auto-
matically shift down to the lowest possible
gear, pull and hold the left shift paddle.
Driving off with Launch Control
There is no downshifting for kickdown.
To drive off with Launch Control, proceed as
follows:
▷
Automatic upshifting is prevented in
manual mode.
In manual mode, the Steptronic transmis-
sion does not shift up automatically when
speed limits are reached.
1. Switch on drive-ready state.
2. Engage forward gear.
3.
Press the My Modes button on the
center console.
Enabling advanced mode
Advanced mode turns on in the following sit-
uations, for example:
4. Enable the driving dynamics setting:
"SPORT PLUS".
▷
▷
The transmission is in manual mode.
5. With the left foot, press down forcefully on
the brake.
"SPORT PLUS": Settings for drive system
in Sport Mode from My Modes.
6. Press the accelerator pedal all the way
down and hold.
Steptronic Sport
transmission: Launch
Control
Launch Control information is displayed in
the instrument cluster.
7. The starting engine speed adjusts. Wait
briefly until the engine speed is constant.
Keep the accelerator pedal in this position.
Principle
8. Release the brake within a few seconds of
the Launch Control information illuminating.
Launch Control ensures optimum acceleration
on roads with good traction and with dry ambi-
ent conditions.
The vehicle accelerates.
Upshifting is performed automatically.
Launch Control stays on as long as the
Launch Control information is displayed
and the accelerator pedal is not released.
General information
Using Launch Control causes premature com-
ponent wear since this function represents a
very heavy load for the vehicle.
Additional information:
Setting for increased driving dynamics, refer to
page 209.
Do not turn the steering wheel when driving off
with Launch Control.
127
Driving
CONTROLS
Repeated use during a trip
Display in the instrument cluster
After Launch Control has been used, the trans-
mission must cool down for a short time before
Launch Control can be used again. Launch
Control adjusts to the surrounding conditions
when used again.
After using Launch Control
To support driving stability, reactivate Dynamic
Stability Control as soon as possible.
▷
▷
▷
Arrow 1: The SPORT BOOST function is ac-
tive.
Sport Boost function
Arrow 2: Countdown, the SPORT BOOST
function is active.
Principle
Arrow 3: The SPORT BOOST function is
used for maximum acceleration.
The SPORT BOOST function can be used for
upcoming acceleration, for example.
This function is operated with the shift paddles
on the steering wheel.
Using the function
1. SPORT BOOST: Pull and hold the left shift
paddle until this display appears, arrow 1.
The system prepares the vehicle.
▷
▷
The function is active.
Overview
A countdown is displayed on the instru-
ment cluster, arrow 2.
2. Before the countdown changes to 0, press
the accelerator pedal.
▷
▷
The vehicle accelerates.
BOOST: This display is shown on the
instrument cluster, arrow 3.
The countdown can be restarted, for example
if the function cannot be used immediately.
The shift paddles are located on the steering
wheel.
To restart the countdown, pull and hold the left
shift paddle again until the countdown is reset.
Stopping the function
The SPORT BOOST function is automatically
interrupted if the countdown has reached 0
or if the function was used in the acceleration
process.
128
Driving
CONTROLS
Deactivating the function
Displays in the instrument cluster
SPORT BOOST: Pull and hold the right shift
paddle until this display goes out.
If applicable, the driving mode
selected is displayed on the in-
strument cluster.
My Modes
My Modes in detail
Principle
My Modes are used to adjust vehicle handling
and customize the overall experience in the
interior.
General information
Various My Modes are available depending on
vehicle equipment.
The vehicle can be adapted depending on the
situation using the various My Modes.
Some My Modes affect vehicle handling. As
such, these are also referred to as drive
modes.
General information
This affects the following systems, depending
on vehicle equipment:
Personal Mode
Personal Mode is a drive mode that provides
comfort-related settings.
▷
▷
▷
▷
▷
▷
▷
Drive system.
Steering.
Suspension.
Sport Mode
Sport Mode is a drive mode that provides in-
creased vehicle agility.
Cruise control.
Display on the instrument cluster.
Comfort functions in vehicle interior.
BMW IconicSounds.
Individual settings, e.g., for the driving dynam-
ics, chassis, and drive system, can be config-
ured as needed.
"SPORT PLUS": Under Driving Dynamics, this
setting deactivates Dynamic Stability Control,
thus limiting driving stability.
Overview
Additional information:
▷
Dynamic Stability Control, refer to
page 208.
▷
Setting for increased driving dynamics, re-
fer to page 209.
Efficient Mode
Efficient Mode is a drive mode that provides
consumption-optimized tuning and an antici-
patory display.
My Modes button on the center con-
sole.
129
Driving
CONTROLS
Additional information:
4. "Start mode"
▷
Efficient mode, refer to page 322.
5. Select the desired mode.
More My Modes
Depending on the vehicle equipment, more My
Modes are available that change the ambiance
in the vehicle interior:
Drive-off assistant
Principle
▷
▷
▷
▷
Expressive Mode.
Digital Art Mode.
Relax Mode.
On inclines, in selector lever position D, L, S, or
R, this system prevents the vehicle from rolling
opposite the set driving direction and provides
drive-off support.
Silent Mode.
Driving off
Engage a gear position and step on the accel-
erator pedal to drive off.
Selecting My Modes
To select My Modes, proceed as follows:
The parking brake is released automatically.
Depending on the load and driving situation or
when a trailer is used, the vehicle may roll back
slightly.
1.
Press the My Modes button on the
center console.
2. Select the desired mode.
If necessary, activate Automatic Hold.
Additional information.
Configuring My Modes
Some My Modes can be configured individu-
ally.
Automatic Hold, refer to page 132.
Parking brake
1.
Press the My Modes button on the
center console.
2. Select the desired mode.
3. Select the settings icon.
Principle
The parking brake is used to prevent the vehi-
cle from rolling away when it is parked.
4. Select the desired settings.
Safety information
Changing the start mode
Some My Modes can be set as the start mode.
Warning
The set start mode activates when drive-ready
state is turned on.
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of accident,
injury, and property damage. Before leaving
the vehicle, secure the vehicle against rolling
away.
1.
Press the My Modes button on the
center console.
2. Select the desired mode.
In order to ensure that the vehicle is secured
against rolling away, follow the following:
3.
Select the settings icon.
130
Driving
CONTROLS
▷
▷
Set the parking brake.
Setting the parking brake
Automatic transmission: Make sure that
selector lever position P is engaged.
With a stationary vehicle
▷
▷
On uphill grades or on downhill slopes,
turn the front wheels in the direction of
the curb.
To engage the parking brake, press
the parking brake button on the center
console.
On uphill grades or on downhill slopes,
also secure the vehicle, for instance with
a wheel chock.
The LED illuminates.
The indicator light for the parking brake
illuminates red.
The parking brake is engaged and
transmission lock is engaged.
Warning
Unattended children or animals in the vehicle
can cause the vehicle to move and endanger
themselves and traffic, for example, due to
the following actions:
While driving
Using the parking brake while driving serves as
emergency braking.
▷
▷
▷
Establishing standby.
To brake the vehicle, press and hold
the parking brake button on the center
console. The vehicle brakes hard for as
long as the button is pressed.
Releasing the parking brake.
Opening and closing the doors or win-
dows.
▷
▷
Engaging selector lever position N.
Using vehicle equipment.
The indicator light for the parking brake
illuminates red, a signal sounds, and
the brake lights illuminate.
There is a risk of accident, injury, and prop-
erty damage. Do not leave children or ani-
mals unattended in the vehicle. Take the ve-
hicle key with you when exiting and lock the
vehicle.
A Check Control message is displayed.
The parking brake is engaged and the trans-
mission lock is set when the vehicle is station-
ary.
Overview
Engaging the parking brake
automatically
In some situations, the parking brake is en-
gaged automatically, e.g., through Automatic
Hold.
To apply the parking brake automatically when
drive-ready state is turned off, configure the
system as follows:
1. Go through the menu as follows: Apps
menu / "Vehicle" / "Driving settings" /
The parking brake button is located on
the center console.
131
Driving
CONTROLS
"Drivetrain and chassis" / "Apply parking
brake".
A Check Control message is displayed.
After getting out of the vehicle, secure it to pre-
vent it from rolling away, using a wheel chock,
for example.
2. Select the desired setting.
In selector lever position N, the parking brake
does not engage automatically.
After a power interruption
To reestablish parking brake operability after
a power interruption, an initialization may be
required.
Releasing the parking brake
Releasing the parking brake manually
To release the parking brake manually, pro-
ceed as follows:
1. Activate standby state.
1. Switch on drive-ready state.
2.
3.
Press the parking brake button on
the center console.
2.
Push the parking brake button on
the center console while pressing the brake
pedal.
Press the parking brake button
again after 2 seconds.
The LED and the indicator light go out.
The parking brake is released.
The Check Control messages for the park-
ing brake go out.
The transmission lock remains engaged
until a gear position is selected.
Function-related noises are normal.
The indicator light for the parking brake
indicates that the parking brake is
ready for operation again.
Releasing the parking brake
automatically
The parking brake is released automatically
when you drive off.
Automatic Hold
The LED and the indicator light go out.
Principle
Using the parking brake via iDrive
Automatic Hold provides assistance by auto-
matically applying and releasing the brake,
e.g., when driving off on inclines or in stop-
and-go traffic.
The parking brake can be engaged or disen-
gaged via iDrive. Additional information is also
displayed.
1. To operate the parking brake via iDrive, go
through the menu as follows. Apps menu /
"Vehicle" / "Driving settings" / "Drivetrain
and chassis" / "Apply parking brake".
When a gear position is engaged, the vehicle
is automatically held in place when it is station-
ary.
2. Select the desired setting.
General information
The parking brake engages automatically if the
following requirements are met:
Malfunction
If the parking brake fails or malfunctions, se-
cure the vehicle so that it does not roll away
before you exit.
132
Driving
CONTROLS
▷
▷
If drive-ready state is turned off.
There is a risk of accident, injury, and prop-
erty damage. Do not leave children or ani-
mals unattended in the vehicle. Take the ve-
hicle key with you when exiting and lock the
vehicle.
The driver’s door is open for more than one
second and no pedal is pressed during this
time.
▷
If the parking brake is used to brake the
vehicle to a stop while driving.
In selector lever position N, Automatic Hold is
temporarily deactivated.
Overview
Safety information
Warning
An unsecured vehicle can begin to move and
possibly roll away. There is a risk of accident,
injury, and property damage. Before leaving
the vehicle, secure the vehicle against rolling
away.
The Automatic Hold button is located
on the center console.
In order to ensure that the vehicle is secured
against rolling away, follow the following:
▷
▷
Set the parking brake.
Activating Automatic Hold
To activate Automatic Hold, proceed as fol-
lows:
Automatic transmission: Make sure that
selector lever position P is engaged.
▷
▷
On uphill grades or on downhill slopes,
turn the front wheels in the direction of
the curb.
1. Switch on drive-ready state.
On uphill grades or on downhill slopes,
also secure the vehicle, for instance with
a wheel chock.
2.
Press the Automatic Hold button on
the center console.
The LED illuminates.
The indicator light for Automatic Hold
illuminates green.
Warning
Automatic Hold is activated.
Unattended children or animals in the vehicle
can cause the vehicle to move and endanger
themselves and traffic, for example, due to
the following actions:
Automatic Hold holding the vehicle
If Automatic Hold is activated and the driver’s
door is closed, the vehicle is automatically se-
cured to prevent it from rolling away after stop-
ping.
▷
▷
▷
Establishing standby.
Releasing the parking brake.
Opening and closing the doors or win-
dows.
As soon as Automatic Hold secures the
vehicle to prevent it from rolling away,
▷
▷
Engaging selector lever position N.
Using vehicle equipment.
133
Driving
CONTROLS
the indicator light for the parking brake illumi-
nates green.
Automatic parking brake application
The parking brake is automatically set if drive-
ready state is switched off while the vehicle is
being held by Automatic Hold or if the vehicle
is exited.
The indicator light for the parking brake
changes from green to red.
The parking brake is not set automatically if
the drive-ready state was switched off while
the vehicle was coasting. Automatic Hold is
temporarily deactivated in this case.
Driving off
Press the accelerator pedal to drive off.
The brake is released automatically and the
indicator light of the parking brake is no longer
illuminated.
The vehicle may roll back slightly when driving
off, depending on the load and driving situation
or when towing a trailer.
Use the parking brake as needed to prevent
the vehicle from rolling back when driving off.
Deactivate Automatic Hold
To deactivate Automatic Hold, proceed as fol-
lows:
Press the Automatic Hold button on the
center console.
The LED goes out.
The indicator light for Automatic Hold
goes out.
Automatic Hold is deactivated.
If the vehicle is being held by Automatic Hold,
also press the brake pedal when deactivating.
134
