Deutsch
EnglishOpening and closing -> Window for your BMW i5 2023-2025
Opening and closing
CONTROLS
The indicator light illuminates for approx.
2 seconds and then continues to flash.
With the vehicle key
▷
After turning off the standby state, an
option to turn off the interior motion sensor
and the tilt alarm sensor will be displayed
on the control display.
Opening windows
Press and hold the button on the vehi-
cle key after unlocking.
The tilt alarm sensor and interior motion sen-
sor are switched off until the vehicle is locked
again.
The windows open for as long as the button
on the vehicle key is pressed.
Closing the windows
Ending the alarm
Unlock the vehicle.
With Comfort Access: press and hold
the button on the vehicle key after lock-
ing.
If the vehicle is unlocked with the integrated
key, the drive-ready state must subsequently
be turned on via the emergency detection of
the vehicle key.
The windows close for as long as the button
on the vehicle key is pressed.
Depending on the vehicle equipment, exterior
mirrors are folded in unless they were folded
in during locking. The exterior mirrors are not
folded in when the hazard warning flashers are
switched on.
Window
General information
When a window is frequently opened to the
same position, this task can be performed by
the BMW Intelligent Personal Assistant. This is
useful if you frequently use the same parking
garage, for example.
On the door handle
Principle
The windows can be closed using the door
handle without operating the vehicle key.
Additional information:
The vehicle key is automatically detected near
the vehicle.
BMW Intelligent Personal Assistant, refer to
page 58.
General information
The function is available with Comfort Access.
Safety information
Depending on national-market version, the
windows can also be closed via the door han-
dle using a compatible smartphone and digital
key.
Warning
When operating the windows, body parts and
objects can be jammed. There is a risk of in-
jury or risk of damage to property. Make sure
that the travel path of the windows is clear
while opening and closing.
Additional information:
BMW Digital Key, refer to page 91.
99
Online Edition for Part no. 01405B37D97 - II/24
Opening and closing
CONTROLS
Functional prerequisites
Functional requirements
▷
Carry the vehicle key with you, for instance
in your pants pocket.
▷
Standby state is switched on.
▷
Drive-ready state is switched on.
▷
Bluetooth must be activated on the smart-
phone to close the window(s) using the dig-
ital key.
The vehicle key or digital key must be inside
the vehicle.
Opening windows
Closing the windows
▷
Press the switch to the resistance
point.
The window opens while the switch
is being held.
▷
Press the switch beyond the resist-
ance point.
The window opens automatically.
Pressing the switch again stops the motion.
Closing the windows
Touch the grooved surface on the door handle
of a closed front door with your finger and hold
it there without grasping the recessed grip.
▷
Pull the switch to the resistance
point.
The window closes while the switch
is being held.
In addition to locking, the windows and glass
sunroof with sun protection will be closed.
▷
Pull the switch beyond the resist-
ance point.
Depending on the vehicle equipment, exterior
mirrors are folded in unless they were folded
in during locking. The exterior mirrors are not
folded in when the hazard warning flashers are
switched on.
The window closes automatically.
Pulling again stops the motion.
Anti-trap mechanism
Inside the vehicle
Principle
The anti-trap mechanism prevents objects or
body parts becoming jammed between the
door frame and window while a window is be-
ing closed.
Overview
General information
If resistance or blockage is detected while a
window is being closed, the closing will be in-
terrupted.
Power windows
100
Online Edition for Part no. 01405B37D97 - II/24
Opening and closing
CONTROLS
Safety information
Overview
Warning
Accessories on the windows such as anten-
nas can impact anti-trap mechanism. There
is a risk of injury. Do not install accessories in
the area of movement of the windows.
Closing without the anti-trap
mechanism
Rear window roller blind button.
In case of danger from the outside or if icing
might prevent normal closing, proceed as fol-
lows:
Operating the side roller blinds
Pull out the side roller sunblind using the loop
and hook it onto the holder.
1. Pull the
switch past the resistance
point and hold it there.
The window closes with limited anti-trap
mechanism. If the closing force exceeds a
specific threshold, closing is interrupted.
Operating the rear roller blind
On the driver’s door
Press the button on the driver's door to
open the rear roller blind if closed or to
close the rear roller blind if open.
2. Pull the
switch past the resistance
point again within approx. 4 seconds and
hold it there.
If the button is pressed again while moving,
the rear roller blind moves in the opposite di-
rection.
The window closes without the anti-trap
mechanism.
System limits
Window roller sunblinds
Safety information
Warning
If you can no longer move the rear roller blind
after pressing the button several times, the
overheating protection has activated. The sys-
tem is disabled for a limited time to prevent
overheating. Let the system cool down.
With closed roller sunblinds and open win-
dows, the roller sunblinds may be strained
while driving due to the air stream. The roller
sunblinds may be damaged and vehicle oc-
cupants may be harmed. There is a risk of
injury. Do not open the windows while driving
if the roller sunblinds are closed.
Safety switch
Principle
The safety switch can be used to prevent chil-
dren, for instance, from opening and closing
101
Online Edition for Part no. 01405B37D97 - II/24
